Categories that include the term: ACETAL
|
Balls |  |
Balls - Acetal (Relevance 10/10)
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
|
Balls - Nylon (Relevance 10/10)
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 10/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 10/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 10/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Fasteners | |
Nuts - Dome - Nylon (Relevance 10/10)
Natural Nylon.
|
Nuts - Hexagonal - Nylon (Relevance 10/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 10/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 10/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 10/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 10/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 10/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Nylon (Relevance 10/10)
|
Screws - Machine - Nylon (Relevance 10/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - Nylon - Countersunk Head (Relevance 10/10)
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Socket - Cap - Nylon (Relevance 10/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Socket Set Screws - Acetal Tipped (Relevance 10/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Nylon Tipped (Relevance 10/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 10/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Materials | |
Rod - Round - Acetal (Relevance 10/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Nylon (Relevance 10/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Plain Bearings | |
Bushes - Plastic - Natural Nylon - Unflanged (Relevance 10/10)
Nominal clearance on ID. Nominal oversize on OD for push-fit in housing. Pricing is highly quantity dependant. Please enquire.
|
Rollers | |
Rollers - Nylon Tyre (Relevance 10/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Spacers | |
Spacers - Hex - Threaded - Nylon (Relevance 10/10)
Threaded Hex Spacers.
|
Spacers - Round - Through Bore - Nylon (Relevance 10/10)
Shaft spacers - Nylon
|
Washers | |
Washers - Flat - Nylon (Relevance 10/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Shoulder - Nylon (Relevance 10/10)
|
Balls | |
Balls - Bored - Plastic (Relevance 3/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Bearings | |
Bearings - High Speed Cage (Relevance 3/10)
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
Bearings in this listing have various types of high speed cages. Speed ratings range from 20 percent to 80 percent increase on standard cage types. Please contact us for a data sheet on the specific size you require.
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 3/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 3/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 3/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Fasteners | |
Screws - Hex Head - Plastic (Relevance 3/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Thumb - Plain (Relevance 3/10)
Brass, steel, aluminum and stainless and nylon.
|
Threaded Rod - Allthread - Plastic (Relevance 3/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Gears and Gearing | |
Gears - Mitre - 16 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 24 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 32 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 48 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass, carbon steel and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Brass and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.6 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 32 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 48 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Flexible (Relevance 3/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Gears - Racks - Flexible - Guide Rails (Relevance 3/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Gears - Racks - Module 0.4 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.5 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.8 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1.25 (Relevance 3/10)
20 Degree Pressure Angle. Acetal.
Plastic.
|
Gears - Racks - Module 1.5 (Relevance 3/10)
20 Degree Pressure Angle. Carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 2 (Relevance 3/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 3 (Relevance 3/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - 16 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 16 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 64 Pitch (Relevance 3/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 3/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.4 (Relevance 3/10)
PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 (Relevance 3/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.7 (Relevance 3/10)
PCD = No. of Teeth x 0.700mm. 20 Degree Pressure Angle. Acetal.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.8 (Relevance 3/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 3/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.25 (Relevance 3/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.5 (Relevance 3/10)
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2 (Relevance 3/10)
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2.5 (Relevance 3/10)
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 3 (Relevance 3/10)
PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Insert Bearings and Housings | |
Bearings - For Plastic Housings (Relevance 3/10)
Ideal for wet conditions. Includes Acetal and Stainless grades 316 and 440C
Load and speed calculations are for reference only. Testing is recommended.
|
Roller Chain and Sprockets | |
Chain - Roller - Plastic - Simplex (Relevance 3/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 3/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Spacers - Round - Hobby (Relevance 3/10)
Inexpensive nylon spacers for hobby applications
|
Universal Joints | |
Universal Joints - Plastic (Relevance 3/10)
Acetal with or without steel inserts.
|
Wheels | |
Wheels - Drive - Friction (Relevance 3/10)
O-Ring tyre - Acetal body - Brass bore insert.
Brass Bore Insert. Acetal Body. Set Screw Locking. Buna N O-Ring Tyre - 70 Durometer. Bore tolerance +0.025/-0.000.
|
Bearings - Specialty | |
Bearings - Ceramic Si3N4 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Handles and Knobs | |
Knobs - Thumb - For Cap Screws (Relevance 1/10)
Four Types and four colours to fit onto Socket Head Cap Screws.
To fit Socket Head Cap Screws (Order Separately - See link at base of listing below). Choice of 4 Colours. Choice of 4 styles. Made From Acetal Resin.
|
Hobby Accessories | |
Gyros - Hobby (Relevance 1/10)
Hitec and more
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Plain Bearings | |
Bushes - Plastic - Hobby (Relevance 1/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 1/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 1/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Pulleys | |
Pulleys - U Groove - Plastic (Relevance 1/10)
Acetal Body with Brass Insert.
|
Rope and Cable | |
Cable - Miniature - Coated (Relevance 1/10)
Lengths will be supplied continuous to a maximum of 3mtrs (ie, 10 x 300mm supplied as 3mtr length)
Recommended that nylon coating is stripped prior to swaging. Sold per length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum.
|
Servo Motors | |
Servomotors - Hobbies Robotics (Relevance 1/10)
Hitec and more
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Servomotors - Hobby - General (Relevance 1/10)
For cars, planes, boats and helicopters. JR, Spektrum, Futaba and Hitec
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Springs | |
Spring Assemblies - Bracket - RINO (Relevance 1/10)
Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.
|
Universal Joints | |
Universal Joints - Plastic with Brass Inserts - Ondrives (Relevance 1/10)
Cross Piece and Inserts: Brass CZ121 Chromate and passivate finish. Body - Black Acetal Max Speed: 1000 Rpm. Temp. Range: -20 Deg C to +60 Deg C. Backlash Free up to 1000,000,000 Turns.
|
|
