Categories that include the terms: ANGLE and BRASS
|
Materials |  |
Angle - Brass (Relevance 10/10)
|
Fasteners | |
Joints - Ball and Socket - Right Angle (Relevance 7/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Nuts - Hexagonal - Brass (Relevance 7/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 7/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Screws - Machine - Brass (Relevance 7/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Brass - Countersunk Head (Relevance 7/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Wood - Brass (Relevance 7/10)
Brass wood screws for models
|
Socket Set Screws - Brass Tipped (Relevance 7/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Threaded Rod - Allthread - Brass (Relevance 7/10)
UNC - UNF - METRIC brass.
|
Gearboxes | |
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 7/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 7/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 7/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 7/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Polished or Raw Brass (Relevance 7/10)
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes
|
Materials | |
Bar - H Section - Brass (Relevance 7/10)
|
Bar - I Beam - Brass (Relevance 7/10)
|
Channel - Brass (Relevance 7/10)
For general hobby applications.
|
Hexagonal Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
|
Rectangular Bar - Brass (Relevance 7/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Rod - Round - Brass (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Square Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
|
Tube - Hexagonal - Brass (Relevance 7/10)
Hexagonal hollow tubing.
|
Tube - Rectangular - Brass (Relevance 7/10)
Rectangular hollow tubing.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Brass (Relevance 7/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Square - Brass (Relevance 7/10)
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Streamline - Brass (Relevance 7/10)
Streamline Brass Tubing.
Teardrop shaped soft brass tubing Enables easier bending Great for tight applications
|
Shim | |
Shim and Foil - Brass (Relevance 7/10)
Brass shim sheet. Very thin foil to thick sizes. Also one assortment pack listed.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes strips, sheets and rolls.
|
Spacers | |
Spacers - Hex - Threaded - Brass (Relevance 7/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Round - Through Bore - Brass (Relevance 7/10)
Shaft spacers - Brass
|
Universal Joints | |
Universal Joints - Plastic with Brass Inserts - Ondrives (Relevance 7/10)
Cross Piece and Inserts: Brass CZ121 Chromate and passivate finish. Body - Black Acetal Max Speed: 1000 Rpm. Temp. Range: -20 Deg C to +60 Deg C. Backlash Free up to 1000,000,000 Turns.
|
Washers | |
Washers - Flat - Brass - Commercial (Relevance 7/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Brass - Precision (Relevance 7/10)
Precision Tolerances. Laminated brass shim washers.
|
Gears and Gearing | |
Gears - Mitre - 24 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 32 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 48 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass, carbon steel and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Brass and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.6 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 32 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 48 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.4 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.5 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.75 (Relevance 3/10)
20 Degree Pressure Angle. Brass and stainless steel.
Metallic.
|
Gears - Racks - Module 0.8 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 64 Pitch (Relevance 3/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.15 (Relevance 3/10)
PCD = No. of Teeth x 0.150mm. 20 Degree Pressure Angle. Brass.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.25 (Relevance 3/10)
PCD = No. of Teeth x 0.250mm. 20 Degree Pressure Angle. Brass and carbon steel.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.4 (Relevance 3/10)
PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 (Relevance 3/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.75 (Relevance 3/10)
PCD = No. of Teeth x 0.750mm. 20 Degree Pressure Angle. Brass.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.8 (Relevance 3/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 3/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Materials | |
Balsa Wood - Rectangle (Relevance 3/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Triangle (Relevance 3/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Model Kit Accessories | |
Model Kit Abrasives (Relevance 3/10)
For a professional finish
|
Clutches and Brakes | |
Clutches - Slip - Inline (Relevance 1/10)
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
|
Couplings | |
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Fasteners | |
Inserts - Expansion (Relevance 1/10)
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
|
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Thumb - Plain (Relevance 1/10)
Brass, steel, aluminum and stainless and nylon.
|
Gears and Gearing | |
Gears - Bevel - 24 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 32 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 48 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.8 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 3 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Internal - 24 Pitch (Relevance 1/10)
Various materials including 2024-T4 Aluminum, 303 stainless steel and brass.
|
Gears - Mitre - 16 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 20 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Unhardened Steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Zinc die cast and steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 20 Degree (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 64 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 72 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 96 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 120 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - Flexible (Relevance 1/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Gears - Racks - Module 1.25 (Relevance 1/10)
20 Degree Pressure Angle. Acetal.
Plastic.
|
Gears - Racks - Module 1.5 (Relevance 1/10)
20 Degree Pressure Angle. Carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 2 (Relevance 1/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 3 (Relevance 1/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - 16 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 16 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 - Hobby - Economy (Relevance 1/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle - POM Plastic
Plastic Only Inexpensive for hobby and toy use No locking mechanisms
|
Gears - Spur - Module 0.7 (Relevance 1/10)
PCD = No. of Teeth x 0.700mm. 20 Degree Pressure Angle. Acetal.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.25 (Relevance 1/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.5 (Relevance 1/10)
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2 (Relevance 1/10)
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2.5 (Relevance 1/10)
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 3 (Relevance 1/10)
PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears and Gearing - Antibacklash | |
Gears - Spur - Antibacklash - 32 Pitch (Relevance 1/10)
Steel - Stainless Steel - Aluminium - 20 Degree Pressure Angle.
|
Gears and Gearing - Matched Sets | |
Gears - Bevel - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets. For 90 degree angle power transfer.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. See Gears - Mitre for 1:1 ratios.
|
Gears - Mitre - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets - 1:1 Ratio. Stainless steel and aluminium.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90 degree angle.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Plastic with Knurl (Relevance 1/10)
Brass threaded insert Knurled circumference to assist with grip
|
Knobs - Lever (Relevance 1/10)
Lever knobs with moulded female threads, ideal for direct attachment to operating levers. Plastic (high grade gloss black phenolic) with Steel insert. Temperature Range: -30°C to +140°C. All knobs are fitted with a brass female insert.
|
Knobs - Pointer - Aluminium and Plastic (Relevance 1/10)
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
|
Hinges | |
Hinges - Flexi-Hinge - Precision (Relevance 1/10)
Double and Single Ended - Limited Angle Rotary Applications.
Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature.
|
Hobby Condensed Selection | |
Hobby Gears - Spur - Module 0.4 (Relevance 1/10)
A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.
|
Hobby Gears - Spur - Module 0.5 (Relevance 1/10)
A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.
|
Ladder Chain and Sprockets | |
Chain - Ladder - 3.750mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 4.242mm Pitch - Size 21 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 4.699mm Pitch - Size 19 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 6.350mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
Chain - Ladder - 7.264mm Pitch - Size 18 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 9.525mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
|
Levers | |
Levers - Control Handles - Flat (Relevance 1/10)
Steel Parts: Quality class 5.8. Ball Knob: Black duroplastic FS31 / Surface Finish: Black oxide. Can be used for simpler clamping applications and switching operations. If necessary there must be enough space to turn the handle through an angle of 360°. The star drive hole model is designed to allow turning in steps of 45°.
|
Mounts and Vibration Control | |
Adjusters - Tilt (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25° from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.
|
Dampeners - Bushings - Silicone (Relevance 1/10)
Protects fragile subjects from micro-vibrations and light shocks.
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
|
Mounts - Cylindrical - Square (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
|
Mounts - Square (Relevance 1/10)
Fastener may be steel, brass or zinc plated. Natural rubber isolator.
|
Suspension Units - Rubber - Square - Insert Type (Relevance 1/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Pulleys | |
Pulleys - Flat Belt (Relevance 1/10)
Polycarbonate pulleys for flat belts 6mm or 6.35mm wide.
Aluminium Knurled Inserts. Gold Iridite Brass Knurled Inserts. Set Screw Locking.
|
Pulleys - U Groove - Plastic (Relevance 1/10)
Acetal Body with Brass Insert.
|
Spacers | |
Spacers - Round - Threaded (Relevance 1/10)
Brass or 303 Stainless Steel
|
Storage | |
Enclosures - Plastic ABS (Relevance 1/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Made with ABS Material, moulded in dark grey. Bosses on internal base allow fixing of PCBs horizontally, or connection of terminals, etc. The lid and base incorporate a tongue and groove sealing system with a neoprene gasket. Lid fixing screws are M4 stainless steel (non-metallic) into threaded brass inserts. Designed to IP65 of IEC529 and NEMS 4 (dust and hoseproof).
|
Wheels | |
Wheels - Drive - Friction (Relevance 1/10)
O-Ring tyre - Acetal body - Brass bore insert.
Brass Bore Insert. Acetal Body. Set Screw Locking. Buna N O-Ring Tyre - 70 Durometer. Bore tolerance +0.025/-0.000.
|
Worms and Worm Gears | |
Worm Gears - 24 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 1) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 2) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 2) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 3) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
25 Degree Pressure Angle - 15.95 Degree Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 2) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 6) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
25 Degree Pressure Angle - 14.2 Degree Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 64 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.5 (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.18 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
|
