Categories that include the terms: BALLS and STAINLESS and STEEL and 440C and GRADE
|
Balls |  |
Balls - Stainless Steel - 304 Grade (Relevance 10/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 10/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 10/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 10/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 9/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 9/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Balls | |
Balls - Bored - Steel (Relevance 6/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 6/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Fasteners | |
Nuts - Cap - Stainless Steel (Relevance 6/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 6/10)
Stainless Steel.
|
Nuts - Wing - Stainless Steel (Relevance 6/10)
304 and 316 Stainless Wing Nuts
|
Pins - Dowel - Standard - Stainless Steel (Relevance 6/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 6/10)
304 and 420 grades DIN1481.
|
Screws - Machine - Stainless Steel (Relevance 6/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 6/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 6/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 6/10)
301 S11/S22 Stainless Steel.
|
Snaprings - Internal - Stainless Steel (Relevance 6/10)
301 S11/S22 Stainless Steel.
|
Shim | |
Shim and Foil - Stainless Steel (Relevance 6/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Spacers | |
Spacers - Round - Through Bore - Stainless Steel (Relevance 6/10)
Shaft spacers - Stainless Steel
|
Washers | |
Washers - Cup - Stainless Steel (Relevance 6/10)
For countersunk screws.
Stainless Steel cup washers.
|
Balls | |
Balls - Chrome Steel (Relevance 5/10)
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
|
Fasteners | |
Nuts - Hexagonal - Half - Stainless Steel (Relevance 5/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 5/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 5/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Pins - Clevis - Stainless Steel 304 (Relevance 5/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 5/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Stainless Steel (Relevance 5/10)
Split pins.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 5/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Stainless Steel (Relevance 5/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Linear Motion Bearings | |
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 5/10)
For running on shafts fixed at the ends.
|
Materials | |
Rod - Round - Stainless Steel (Relevance 5/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Tube - Round - Stainless Steel (Relevance 5/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 5/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 5/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 5/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 5/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 5/10)
|
Spacers | |
Spacers - Hex - Threaded - Stainless Steel (Relevance 5/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Washers | |
Washers - Disc Spring - Stainless Steel (Relevance 5/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Stainless Steel - Commercial (Relevance 5/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 5/10)
Precision Tolerances.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 5/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 5/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Balls | |
Balls - Bored - Plastic (Relevance 4/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Ruby - Synthetic (Relevance 4/10)
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
|
Balls - Sapphire - Synthetic (Relevance 4/10)
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
|
Balls - Tungsten Carbide (Relevance 4/10)
Extreme hardness and wear resistance.
Tolerances available on request. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Economy (Relevance 4/10)
Taiwanese Hobby Bearings - Inexpensive Option. The type you find at most hobby shops.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Flanged (Relevance 4/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 4/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Specialty | |
Bearings - Acetal - with Glass Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 4/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Fasteners | |
Joints - Ball and Socket - Right Angle (Relevance 4/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Joints - Clevis - Steel (Relevance 4/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Nuts - Dome - Steel (Relevance 4/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Titanium - CP Grade 1 (Relevance 4/10)
METRIC. CP Grade 1.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Hex Head - Titanium Grade 1 (Relevance 4/10)
Fully threaded hex head screws (DIN933)
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Din 933.
|
Screws - Machine - Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Cap - Alloy Steel (Relevance 4/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Stainless (Relevance 4/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Socket Set Screws - Flat Ball Tip (Relevance 4/10)
Grub screws with a rotating flat tip. The ball can rotate up to 9 Deg. to fasten the object securely.
|
Socket Set Screws - Rolling Ball Tip (Relevance 4/10)
Rolling ball tip for locating into a hole
|
Studs - Ball - Threaded (Relevance 4/10)
Zinc Plated Steel DIN 71803 Form C Surface Hardened to 55 HRC (Ball (D1) Only - Thread is Not Hardened)
|
Threaded Rod - Allthread - Steel (Relevance 4/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Polished or Raw Brass (Relevance 4/10)
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Single Assembly (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Single Assembly - Circlip Retained (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Square - Miniature (Relevance 4/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Insert Bearings and Housings | |
Bearings - For Pressed Metal Housings (Relevance 4/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Housing - Base Type (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Housing - Flanged (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 4/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Screws - Ball - Economy - Rolled - Nut Only (Relevance 4/10)
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
|
Screws - Ball - Economy - Rolled - Screw Only (Relevance 4/10)
Match with nut. Accuracy T7 50µm/300mm.
Longer lengths available on request (up to 5600mm). Steel Cf53 or Cf60 induction hardened and polished. Running trach hardened to 60 HRC. Profile: Gothic type rolled. Accuracy T7 50µm/300mm.
|
Screws - Ball - Thomson Saginaw (Relevance 4/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Drive Systems - Leadscrew | |
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 4/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Materials | |
Hexagonal Bar - 303 Stainless (Relevance 4/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Square Bar - 303 Stainless (Relevance 4/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Wire - Steel - Spring - Music Wire (Relevance 4/10)
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
|
Plain Bearings | |
Bushings - Spherical - Steel (Relevance 4/10)
Steel
Compensates for axial loads and misalignment.
|
Pulleys | |
Pulleys - U Groove - Steel (Relevance 4/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 4/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - PTFE Lined (Relevance 4/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 4/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 4/10)
High tensile steel.
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 4/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Rollers | |
Rollers - Steel (Relevance 4/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 4/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Shim | |
Shim and Foil - Steel (Relevance 4/10)
Shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Silver Steel | |
Shafting - Ground - Precision (Relevance 4/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Spacers | |
Spacers - Round - Through Bore - Steel (Relevance 4/10)
Shaft spacers - Steel
|
Springs | |
Plungers - Spring - Smooth (Relevance 4/10)
Stainless Steel or Plastic - No Thread.
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
|
Universal Joints | |
Universal Joints - Steel (Relevance 4/10)
Steel - Cast Zinc - Stainless Steel.
|
Washers | |
Washers - Flat - Carbon Spring Steel - Precision (Relevance 4/10)
Flat Carbon Spring Steel Washers.
|
Washers - Flat - Mild Steel (Relevance 4/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Titanium - CP Grade 1 (Relevance 4/10)
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Balls | |
Balls - Acetal (Relevance 3/10)
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
|
Balls - Acrylic (Relevance 3/10)
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically +/- 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
|
Balls - Ceramic - Silicon Nitride (Relevance 3/10)
Outstanding wear resistance. Good thermal and chemical resistance.
High hardness. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.
|
Balls - Nylon (Relevance 3/10)
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
|
Balls - PTFE (Relevance 3/10)
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 Deg C. Unpolished. Specific Gravity: 2.3.
|
Balls - Phosphor Bronze (Relevance 3/10)
Specific Gravity 8.4
|
Balls - Polypropylene (Relevance 3/10)
Excellent for liquid level float applications.
Tolerance and spherecity: up to and including 25.4mm diameter = +/-0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.
|
Bearings - Thrust | |
Bearings - Thrust - Ball (Relevance 3/10)
3 Piece Thrust Bearings, Shielded and Unshielded.
|
Bearings - Thrust - Ball - Banded (Relevance 3/10)
|
Bearings and Housings | |
Housings - Bearing - Pillow Block - Miniature (Relevance 3/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 3/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Heavy Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Screw Stem (Relevance 3/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Castors - Plate - General Purpose - Ball Bearing - Light Medium Duty (Relevance 3/10)
|
Fasteners | |
Joints - Ball and Socket - In-line (Relevance 3/10)
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 3/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Steel (Relevance 3/10)
Zinc Plated Wing Nuts
|
Pins - Dowel - Standard - Hardened Steel (Relevance 3/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Screws - Hex Head - Steel (Relevance 3/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Machine - Steel - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Alloy Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Handles and Knobs | |
Knobs - Ball - Knock On - Phenolic (Relevance 3/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Knobs - Ball - Threaded - Phenolic (Relevance 3/10)
Moulded from black or red phenolic resin.
Light Weight. Thermal insulating. Non corrosive.
|
Knobs - Ball - Threaded - Phenolic with Shank (Relevance 3/10)
|
Knobs - Ball - Threaded - Plastic with Knurl (Relevance 3/10)
Brass threaded insert Knurled circumference to assist with grip
|
Knobs - Ball - Threaded - Polished Aluminium (Relevance 3/10)
DIN319 Tapped aluminium
Polished with a flash chrome finish
|
Keys and Keysteel | |
Keys - Gib Head - Steel (Relevance 3/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Keys - Woodruff (Relevance 3/10)
Stainless steel and carbon steel
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Diameter (Relevance 3/10)
16mm Diameter with pitches 2.5 to 20mm. Machined or unmachined ends. Nuts sold seperately.
Material : Cf53 induction hardened to HRC 62 (=/- 2). Pitch accuracy : <= 0.1mm / 300mm ISO class 7. Nuts sold seperately.
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 3/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Materials | |
Hexagonal Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Square Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Plain Bearings | |
Bushes - Steel - PTFE Lined - Split (Relevance 3/10)
Similar style to Glacier™ bushes.
|
Reels | |
Reels - Spring Powered - Base Mounted - Steel (Relevance 3/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 3/10)
Includes Miniature Sizes.
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 3/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Spacers | |
Spacers - Hex - Threaded - Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Springs | |
Plungers - Spring - Threaded (Relevance 3/10)
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
|
Washers | |
Washers - Disc Spring - Carbon Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Lock - External Tooth - Spring Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
|
