Categories that include the terms: BEARINGS and NEEDLE and ROLLER and SHELL and TYPE
|
Bearings - Needle Roller |  |
Bearings - Needle Roller - Cage Type (Relevance 10/10)
Cage and Rollers.
|
Bearings - Needle Roller - Shell Type (Relevance 10/10)
Light Weight. Compact Design.
|
Bearings - Needle Roller - Inner Rings (Relevance 9/10)
Hardened sleeves for needle roller bearings.
|
Bearings - Needle Roller - Machined - With Inner Ring (Relevance 8/10)
|
Bearings - Needle Roller - Machined - Without Inner Ring (Relevance 8/10)
|
Bearings and Housings | |
Bearings - Press - Needle Roller - Flange Mounted (Relevance 8/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Specialty | |
Bearings - One Way - Roller (Relevance 6/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 6/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 6/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Rollers | |
Bearings - Pressure Roller - With Urethane OD (Relevance 6/10)
Bearings with Urethane Tyre on OD for applications requiring frictional movement.
For applications including paper and card dispensing and rolling (eg ATM Machines).
|
Bearings - Specialty | |
Bearings - Automotive - Tapered Roller (Relevance 5/10)
|
Cam Followers | |
Cam Followers - Roller Type - Urethane Covered (Relevance 5/10)
Urethane tyred cam followers for noise reduction, reduced wear and non marking
|
Rollers | |
Rollers - Idler - With Sintered Bearing (Relevance 5/10)
|
Batteries | |
Batteries - Coin Type (Relevance 4/10)
Coin type batteries to suit watches, clocks, computers and other equipment. Lithium, Silver Oxide and Alkaline
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 4/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Ball - Single Row - Radial - Economy (Relevance 4/10)
Taiwanese Hobby Bearings - Inexpensive Option. The type you find at most hobby shops.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Flanged (Relevance 4/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 4/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - High Speed Cage (Relevance 4/10)
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
Bearings in this listing have various types of high speed cages. Speed ratings range from 20 percent to 80 percent increase on standard cage types. Please contact us for a data sheet on the specific size you require.
|
Skate Bearings (Relevance 4/10)
Bearings for use with skates and skate boards.
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 4/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Bearings - Grooved | |
Bearings - U Groove Profile OD (Relevance 4/10)
Special OD Bearings.
Contact us for tolerances.
|
Bearings - V Groove Profile OD (Relevance 4/10)
Special OD Bearings.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 4/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ceramic Hybrid (Relevance 4/10)
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
|
Bearings - Unground (Relevance 4/10)
Unground bearings used in trolleys, prams and wheel barrow wheels
|
Model Jet Turbine Bearings (Relevance 4/10)
Bearings developed specifically for use in Model Jet turbines.
These bearings are designed for high speeds usually between 80,000 and 120,000 RPM in short runs. Speeds over 120,000 are often obtainable. Testing is required. High Temperature up to 300 Degrees Celsius. Bearing Type R in the tables indicates Radial (refer our main bearings category).
|
Bearings - Thrust | |
Bearings - Thrust - Ball (Relevance 4/10)
3 Piece Thrust Bearings, Shielded and Unshielded.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 4/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 4/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 4/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 4/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 4/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 4/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 4/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 4/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 4/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 4/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Housings - Bearing - Pillow Block - Miniature (Relevance 4/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 4/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Dental Products | |
Bearings - Dental Applications (Relevance 4/10)
See Dental Handpiece Bearings and Orings for applications by model.
This listing is the basic features of various bearings for dental applications. Please contact us for a dental application list. See - Dental Handpiece Bearings and Orings for applications by model.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels (Relevance 4/10)
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
|
Dual Vee - Guide Wheels - Studded (Relevance 4/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Dual Vee - Tracks with Mounting Holes (Relevance 4/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 4/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Single Assembly (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Single Assembly - Circlip Retained (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Square - Miniature (Relevance 4/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Die Cast (Relevance 4/10)
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
|
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 4/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 4/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Housings - Bearing - Flanged - Square - W300 (Relevance 4/10)
With integral self aligning plain bearing.
Housing : Igumid G. Ball : Highly wear resistant Iglidur W300.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - Offset - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - Round - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - Square - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Pillow Block - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Pillow Block - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Housing - Base Type (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 4/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Plain Bearings | |
Bushes - Aluminium - Frelon Lined (Relevance 4/10)
Self lubricating - Replaces oilite or plastic bearings.
SLIP FIT: Housing bore should be OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be OD -0.000/+0.010. Use freezing method for press fit assembly - freeze bearing to -18 Deg C for 30 minutes. Body: Aluminium. Lining: Frelon.
|
Roller Chain and Sprockets | |
Sprockets - Idler (Relevance 4/10)
Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 4/10)
|
Rollers - Idler - With Aluminium Sleeve (Relevance 4/10)
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
|
Rollers - Nylon Tyre (Relevance 4/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Rollers - Steel (Relevance 4/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Rollers - Track - With Inner Race (Relevance 4/10)
|
Rollers - Urethane Feed - With Hub (Relevance 4/10)
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter Sleeve - Aluminium
|
Rollers - Yoke - Cam (Relevance 4/10)
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking
Polycoated shore 80A cast urethane cover
|
Bearings - Specialty | |
Bearings - Ceramic Si3N4 (Relevance 3/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 3/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Pivot - Flanged (Relevance 3/10)
|
Bearings - Pivot - With Inner Ring (Relevance 3/10)
Note! Minimum quantities apply to production of these items.
|
Bearings - Pivot - Without Inner Ring (Relevance 3/10)
Note! Minimum quantities apply to production of these items.
|
Bearings - Thrust | |
Bearings - Thrust - Ball - Banded (Relevance 3/10)
|
Bearings - Thrust - Plastic - Self Seating (Relevance 3/10)
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
|
Lazy Susan Bearings (Relevance 3/10)
One unit construction for maximum stability and quiet running.
Centre opening allows for a centre post if required.
|
Bearings and Housings | |
Bearings - Press - Sintered Bronze (Relevance 3/10)
Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress.
|
Castors | |
Castors - Plate - General Purpose - Ball Bearing - Light Medium Duty (Relevance 3/10)
|
Clamping and Locking | |
Collars - Shaft - Clamp Type (Relevance 3/10)
|
Shaftloc-tm Simple Type M (Relevance 3/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Couplings | |
Couplings - Jaw Type - With Polyurethane Spider (Relevance 3/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Couplings - Jaw Type - With Rubber Spider (Relevance 3/10)
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Couplings - Slit Type (Relevance 3/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Handles and Knobs | |
Knobs - Pointer - 18T Spline Type (Relevance 3/10)
Push on suits 18 tooth splined 6.35mm (1/4 inch) shaft.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Frelon Lined (Relevance 3/10)
Self aligning. Open or closed. Precision or standard. For rotating and linear motion.
|
Housings - Bearing - Blocks - Thermoplastic (Relevance 3/10)
Iglide L280 / Igus W300 Ball with Thermoplatic Body.
Maintenance Free, Lightweight, Self-Lubricating. Compensates for alignment errors. Temperature Range -40 deg C to +130 deg C. Max. Static Tensile Strength is Long Term. Info for Short Term also available.
|
Insert Bearings and Housings | |
Bearings - For Cast Iron Housings (Relevance 3/10)
With spherical OD for use with cast iron flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.
|
Bearings - For Plastic Housings (Relevance 3/10)
Ideal for wet conditions. Includes Acetal and Stainless grades 316 and 440C
Load and speed calculations are for reference only. Testing is recommended.
|
Bearings - For Pressed Metal Housings (Relevance 3/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Bush Type (Relevance 3/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Linear Motion Bearings | |
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Carriage Assembly (Relevance 3/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 3/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 3/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Mounts and Vibration Control | |
Mounts - Leveling - Base Type - Round (Relevance 3/10)
For loads of 45 to 5350 kg.
|
Suspension Units - Rubber - Square - Insert Type (Relevance 3/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 3/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Sintered - Flanged (Relevance 3/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 3/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Solid - C92300 (Relevance 3/10)
Solid Precision C93200 bronze bushes.
ID Tolerance : -0.0254 / +0.0254 OD Tolerance : +0.0762 LENGTH Tolerance : -0.127 / +0.127. Composition (Approx.) : Copper 83%, Tin 6.7%, Zinc 3%, Lead 7% and small traces of Aluminum, Antimony, Iron, Nickel, Phosphorus, Silcon and Sulpher.
|
Bushes - Bronze - Solid - LG2 (Relevance 3/10)
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Spherical - Sintered (Relevance 3/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Bushes - Plastic - Ertalyte TX (Relevance 3/10)
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
|
Bushes - Plastic - Hobby (Relevance 3/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Plastic - Iglidur G - Flanged (Relevance 3/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Iglidur G - Unflanged (Relevance 3/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Natural Nylon - Unflanged (Relevance 3/10)
Nominal clearance on ID. Nominal oversize on OD for push-fit in housing. Pricing is highly quantity dependant. Please enquire.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 3/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 3/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Steel - PTFE Lined - Split (Relevance 3/10)
Similar style to Glacier™ bushes.
|
Bushings - Spherical - Plastic (Relevance 3/10)
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
|
Bushings - Spherical - Steel (Relevance 3/10)
Steel
Compensates for axial loads and misalignment.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 3/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 3/10)
High tensile steel.
|
Chain - Roller - Metal - Simplex (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Plastic - Simplex (Relevance 3/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 3/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 3/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 3/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 3/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Storage | |
Parts Boxes - Tilt Type (Relevance 3/10)
Tilt pak plastic carry box with 4 self locking drawers
Can be joined togetherto make a double sided case Freestanding or mountable 4 self locking drawers each with 4 compartments
|
Washers | |
Washers - Flat - Commercial - All Types (Relevance 3/10)
Includes all materials listed in other commercial washer categories.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Precision - All Types (Relevance 3/10)
Includes all materials listed in other precision washer categories.
|
Adhesives and Sealants | |
Retaining Compounds (Relevance 1/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Batteries | |
Batteries - Hobby - Lead Acid (Relevance 1/10)
All types of Lead Acid Battery
|
Batteries - Hobby - Lipo (Relevance 1/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom, Hacker. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - NiMH (Relevance 1/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - Nicad (Relevance 1/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Belts | |
Belt Tension Tester (Relevance 1/10)
For testing the tension on assembled timing belts, vee belts, flat belts etc.
Gauges for testing all types of belts when assembled for correct tension.
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 1/10)
Stainless steel ball type cam followers.
|
Castors | |
Castors - Black Rubber (Relevance 1/10)
Black rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
|
