Categories that include the terms: BEARINGS and ONE and WAY and SPRAG and STANDARD
|
Bearings - Clutch |  |
Bearings - One Way - Sprag - Standard (Relevance 10/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Bearings - Specialty | |
Bearings - One Way - Roller (Relevance 9/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Batteries | |
Batteries - Standard (Relevance 4/10)
The Venom standard non-rechargeable battery range includes AA, AAA, C, D and 9V non-rechargeable.
Bulk packs and single cards
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 4/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Ball - Single Row - Radial - Economy (Relevance 4/10)
Taiwanese Hobby Bearings - Inexpensive Option. The type you find at most hobby shops.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Flanged (Relevance 4/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 4/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - High Speed Cage (Relevance 4/10)
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
Bearings in this listing have various types of high speed cages. Speed ratings range from 20 percent to 80 percent increase on standard cage types. Please contact us for a data sheet on the specific size you require.
|
Skate Bearings (Relevance 4/10)
Bearings for use with skates and skate boards.
|
Bearings - Grooved | |
Bearings - U Groove Profile OD (Relevance 4/10)
Special OD Bearings.
Contact us for tolerances.
|
Bearings - V Groove Profile OD (Relevance 4/10)
Special OD Bearings.
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Inner Rings (Relevance 4/10)
Hardened sleeves for needle roller bearings.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 4/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ceramic Hybrid (Relevance 4/10)
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
|
Bearings - Ceramic Si3N4 (Relevance 4/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 4/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Unground (Relevance 4/10)
Unground bearings used in trolleys, prams and wheel barrow wheels
|
Model Jet Turbine Bearings (Relevance 4/10)
Bearings developed specifically for use in Model Jet turbines.
These bearings are designed for high speeds usually between 80,000 and 120,000 RPM in short runs. Speeds over 120,000 are often obtainable. Testing is required. High Temperature up to 300 Degrees Celsius. Bearing Type R in the tables indicates Radial (refer our main bearings category).
|
Bearings - Thrust | |
Bearings - Thrust - Ball (Relevance 4/10)
3 Piece Thrust Bearings, Shielded and Unshielded.
|
Bearings - Thrust - Roller (Relevance 4/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Lazy Susan Bearings (Relevance 4/10)
One unit construction for maximum stability and quiet running.
Centre opening allows for a centre post if required.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 4/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 4/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 4/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 4/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 4/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 4/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 4/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 4/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 4/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 4/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 4/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Housings - Bearing - Pillow Block - Miniature (Relevance 4/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Dental Products | |
Bearings - Dental Applications (Relevance 4/10)
See Dental Handpiece Bearings and Orings for applications by model.
This listing is the basic features of various bearings for dental applications. Please contact us for a dental application list. See - Dental Handpiece Bearings and Orings for applications by model.
|
Fasteners | |
Pins - Taper - Imperial - Standard (Relevance 4/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Socket Set Screws - Cup Point - Standard (Relevance 4/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels (Relevance 4/10)
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Single Assembly (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Single Assembly - Circlip Retained (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Square - Miniature (Relevance 4/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Die Cast (Relevance 4/10)
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
|
Housings - Bearing - Blocks - Frelon Lined (Relevance 4/10)
Self aligning. Open or closed. Precision or standard. For rotating and linear motion.
|
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 4/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 4/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Housings - Bearing - Flanged - Square - W300 (Relevance 4/10)
With integral self aligning plain bearing.
Housing : Igumid G. Ball : Highly wear resistant Iglidur W300.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - Offset - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - Round - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - Square - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Pillow Block - Cast Iron (Relevance 4/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Pillow Block - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Paint | |
Paints - Standard Spray - Tamiya (Relevance 4/10)
Cans of spray paint suitable for painting static models.
Tamiya spray colours provide an impressive finish to static models. When painting figures with a brush, it can be difficult to get paint into creases such as on faces and fabric. Using spray paint is a sure way to get a smooth, even finish. They are also extremely useful for painting large surfaces. Each can contains 100ml of paint, which is enough to fully cover 2 or 3, 1/24 scale sized car bodies. The paint is a synthetic lacquer that cures in a short period of time. Tamiya spray paints are not affected by acrylic or enamel paints. Therefore, following the painting of the entire assembly, details can be added or picked out using enamel and/or acrylic paints. By combining three different paints, the decoration of plastic models will become simpler and more effective.
|
Plain Bearings | |
Bushes - Aluminium - Frelon Lined (Relevance 4/10)
Self lubricating - Replaces oilite or plastic bearings.
SLIP FIT: Housing bore should be OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be OD -0.000/+0.010. Use freezing method for press fit assembly - freeze bearing to -18 Deg C for 30 minutes. Body: Aluminium. Lining: Frelon.
|
Rollers | |
Bearings - Pressure Roller - With Urethane OD (Relevance 4/10)
Bearings with Urethane Tyre on OD for applications requiring frictional movement.
For applications including paper and card dispensing and rolling (eg ATM Machines).
|
Springs | |
Springs - Compression - Standard (Relevance 4/10)
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Cage Type (Relevance 3/10)
Cage and Rollers.
|
Bearings - Needle Roller - Machined - With Inner Ring (Relevance 3/10)
|
Bearings - Needle Roller - Machined - Without Inner Ring (Relevance 3/10)
|
Bearings - Needle Roller - Shell Type (Relevance 3/10)
Light Weight. Compact Design.
|
Bearings - Specialty | |
Bearings - Automotive - Tapered Roller (Relevance 3/10)
|
Bearings - Pivot - Flanged (Relevance 3/10)
|
Bearings - Pivot - With Inner Ring (Relevance 3/10)
Note! Minimum quantities apply to production of these items.
|
Bearings - Pivot - Without Inner Ring (Relevance 3/10)
Note! Minimum quantities apply to production of these items.
|
Bearings - Thrust | |
Bearings - Thrust - Ball - Banded (Relevance 3/10)
|
Bearings - Thrust - Plastic - Self Seating (Relevance 3/10)
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
|
Bearings and Housings | |
Bearings - Press - Sintered Bronze (Relevance 3/10)
Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress.
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 3/10)
Stainless steel ball type cam followers.
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 3/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Castors - Plate - General Purpose - Ball Bearing - Light Medium Duty (Relevance 3/10)
|
Clamping and Locking | |
Collars - Shaft - Standard (Relevance 3/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Couplings | |
Couplings - Helical - Standard (Relevance 3/10)
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Fasteners | |
Pins - Dowel - Standard - Hardened Steel (Relevance 3/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 3/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels - Studded (Relevance 3/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Dual Vee - Tracks with Mounting Holes (Relevance 3/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 3/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Hobby Accessories | |
Propellers - Plane - Electric - Standard (Relevance 3/10)
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Thermoplastic (Relevance 3/10)
Iglide L280 / Igus W300 Ball with Thermoplatic Body.
Maintenance Free, Lightweight, Self-Lubricating. Compensates for alignment errors. Temperature Range -40 deg C to +130 deg C. Max. Static Tensile Strength is Long Term. Info for Short Term also available.
|
Insert Bearings and Housings | |
Bearings - For Cast Iron Housings (Relevance 3/10)
With spherical OD for use with cast iron flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.
|
Bearings - For Plastic Housings (Relevance 3/10)
Ideal for wet conditions. Includes Acetal and Stainless grades 316 and 440C
Load and speed calculations are for reference only. Testing is recommended.
|
Bearings - For Pressed Metal Housings (Relevance 3/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 3/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Carriage Assembly (Relevance 3/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 3/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 3/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 3/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Materials | |
Rod - Round - Bronze - LG2 (Standard) (Relevance 3/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 3/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 3/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Sintered - Flanged (Relevance 3/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 3/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Solid - C92300 (Relevance 3/10)
Solid Precision C93200 bronze bushes.
ID Tolerance : -0.0254 / +0.0254 OD Tolerance : +0.0762 LENGTH Tolerance : -0.127 / +0.127. Composition (Approx.) : Copper 83%, Tin 6.7%, Zinc 3%, Lead 7% and small traces of Aluminum, Antimony, Iron, Nickel, Phosphorus, Silcon and Sulpher.
|
Bushes - Bronze - Solid - LG2 (Relevance 3/10)
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Spherical - Sintered (Relevance 3/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Bushes - Plastic - Ertalyte TX (Relevance 3/10)
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
|
Bushes - Plastic - Hobby (Relevance 3/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Plastic - Iglidur G - Flanged (Relevance 3/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Iglidur G - Unflanged (Relevance 3/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Natural Nylon - Unflanged (Relevance 3/10)
Nominal clearance on ID. Nominal oversize on OD for push-fit in housing. Pricing is highly quantity dependant. Please enquire.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 3/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 3/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Steel - PTFE Lined - Split (Relevance 3/10)
Similar style to Glacier™ bushes.
|
Bushings - Spherical - Plastic (Relevance 3/10)
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
|
Bushings - Spherical - Steel (Relevance 3/10)
Steel
Compensates for axial loads and misalignment.
|
Retaining Rings and Clips | |
Circlips - External - Basic (Standard) (Relevance 3/10)
Imperial and metric DIN471 / N1400 / D1460.
|
Rollers | |
Rollers - Idler - With Sintered Bearing (Relevance 3/10)
|
Adhesives and Sealants | |
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Retaining Compounds (Relevance 1/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Stainless Steel - 316L Grade (Relevance 1/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Belts | |
Belts - Timing - 2.032mm Pitch - MXL (Relevance 1/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.073mm Pitch - 40DP (Relevance 1/10)
Standard Series Timing Belts 2.072mm or 0.08016 inch pitch.
Pitch (P) - 2.073mm (0.0816 inch). Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 1/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 9.525mm Pitch - L (Relevance 1/10)
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Pitch (P) - 9.525mm (0.200 inch). Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
|
Books and DVD | |
Books - Engineering (Relevance 1/10)
Machinery handbook contains standards, materials and other general engineering information.
|
Clamping and Locking | |
Rings - Tolerance (Relevance 1/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Cleaning | |
Cleaning Products - Miscellaneous (Relevance 1/10)
Products related to bearing and power transmission work. No overseas sales.
Some items in this category are marked as only available for collection.
|
Couplings | |
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Electrical | |
Power Supplies (Relevance 1/10)
24 V DC.
Standard : 24V DC Output, 110V AC input. Available on special order : 12V DC Output, 220/230V AC input.
|
Fasteners | |
Joints - Ball and Socket - Right Angle (Relevance 1/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Machine - PEEK - Pan Head (Relevance 1/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Socket Set Screws - Cone Point (Relevance 1/10)
Cone point grub screws
|
Yoke Ends - Blank (Relevance 1/10)
Linkage Connectors with blank ends - no hole
Drop forged steel machined to SAE standards Also see clevis joints
|
Yoke Ends - Threaded (Relevance 1/10)
Linkage Connectors
Drop forged steel machined to SAE standards Also see clevis joints
|
Gearboxes | |
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 1/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 1/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 1/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 1/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 1/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - DC - Size 20 Low Cost (Relevance 1/10)
20mm Gearhead Body Diameter. Low cost. 70 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 27 Low Cost (Relevance 1/10)
27mm Gearhead Body Diameter. Low cost. 36 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 37/350 Low Cost (Relevance 1/10)
37mm Gearhead Body Diameter. Low cost. 160 RPM Output Speed. One model only. Reversible.
|
Handles and Knobs | |
Knobs - Ball - Knock On - Phenolic (Relevance 1/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Hobby Accessories | |
Accessories - Hobby - Body Clips (Relevance 1/10)
Large and small body clips. Fluoro or standard. Plastic coated or anodised. Range of colours. Bent and straight.
|
Wire - Silicone (Relevance 1/10)
Silicone Wire in various colours and gauges
|
Ladder Chain and Sprockets | |
Chain - Ladder - 6.350mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
|
