Categories that include the terms: BUSHES and PLASTIC and HOBBY
|
Plain Bearings |  |
Bushes - Plastic - Hobby (Relevance 10/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Hobby Condensed Selection | |
Hobby Gears - Worm and Wheel 40 : 1 Plastic (Relevance 9/10)
Popular Hobby Set
1 start 40 tooth gear.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 9/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Plastic - Ertalyte TX (Relevance 9/10)
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
|
Bushes - Plastic - Iglidur G - Flanged (Relevance 9/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Iglidur G - Unflanged (Relevance 9/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Natural Nylon - Unflanged (Relevance 9/10)
Nominal clearance on ID. Nominal oversize on OD for push-fit in housing. Pricing is highly quantity dependant. Please enquire.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 9/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 9/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushings - Spherical - Plastic (Relevance 9/10)
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
|
Balls | |
Balls - Bored - Plastic (Relevance 5/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Batteries | |
Batteries - Hobby - Lipo (Relevance 5/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom, Hacker. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - NiMH (Relevance 5/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - Nicad (Relevance 5/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Fasteners | |
Joints - Clevis - Plastic (Relevance 5/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Nuts - Dome - Nylon (Relevance 5/10)
Natural Nylon.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 5/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 5/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 5/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 5/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Screws - Hex Head - Plastic (Relevance 5/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Self Tapping - For Plastics (Relevance 5/10)
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics Be sure to select correct screw for hard or soft plastic threadcutting
|
Socket Set Screws - Acetal Tipped (Relevance 5/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Nylon Tipped (Relevance 5/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Threaded Rod - Allthread - Plastic (Relevance 5/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Gearmotors | |
Gearmotors - Basic - Hobby Kits (Relevance 5/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gears and Gearing | |
Gears - Spur - Module 0.5 - Hobby - Economy (Relevance 5/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle - POM Plastic
Plastic Only Inexpensive for hobby and toy use No locking mechanisms
|
Hobby Accessories | |
Accessories - Hobby - Body Clips (Relevance 5/10)
Large and small body clips. Fluoro or standard. Plastic coated or anodised. Range of colours. Bent and straight.
|
Accessories - Hobby - General (Relevance 5/10)
General hobby supplies
Velcro Strip - ESC Fans - Heat Shrink - Motor Cooling Stands - Spring Dyno Camera Eye - Tuning Mat - Frequency Keys
|
Hobby Condensed Selection | |
Hobby Gears - Spur - 48DP (Relevance 5/10)
A small selection of popular 48DP Plastic/ Metal Pinion and Spur gears
See main listings under Gears for sizes not listed here To work out the pitch diameter of a 48DP spur gear, divide multiply the no of teeth by 0.52917.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 5/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Insert Bearings and Housings | |
Bearings - For Plastic Housings (Relevance 5/10)
Ideal for wet conditions. Includes Acetal and Stainless grades 316 and 440C
Load and speed calculations are for reference only. Testing is recommended.
|
Materials | |
Rod - Round - Acetal (Relevance 5/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Plain Bearings | |
Bushes - Aluminium - Frelon Lined (Relevance 5/10)
Self lubricating - Replaces oilite or plastic bearings.
SLIP FIT: Housing bore should be OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be OD -0.000/+0.010. Use freezing method for press fit assembly - freeze bearing to -18 Deg C for 30 minutes. Body: Aluminium. Lining: Frelon.
|
Bushes - Bronze - Sintered - Flanged (Relevance 5/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 5/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Solid - C92300 (Relevance 5/10)
Solid Precision C93200 bronze bushes.
ID Tolerance : -0.0254 / +0.0254 OD Tolerance : +0.0762 LENGTH Tolerance : -0.127 / +0.127. Composition (Approx.) : Copper 83%, Tin 6.7%, Zinc 3%, Lead 7% and small traces of Aluminum, Antimony, Iron, Nickel, Phosphorus, Silcon and Sulpher.
|
Bushes - Bronze - Solid - LG2 (Relevance 5/10)
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Spherical - Sintered (Relevance 5/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Bushes - Steel - PTFE Lined - Split (Relevance 5/10)
Similar style to Glacier™ bushes.
|
Remote Control Aircraft | |
Foam Plane Kits Electric - Hobby Zone (Relevance 5/10)
Foam Plane Kits Electric - Hobby Zone
This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands Include: Super Cub LP
|
Roller Chain and Sprockets | |
Chain - Roller - Plastic - Simplex (Relevance 5/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 5/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 5/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 5/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 5/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 5/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 5/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Rollers | |
Rollers - Nylon Tyre (Relevance 5/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Shaft and Shafting | |
Shafting - Ground - Hobby (Relevance 5/10)
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc Not recommended for use with precision steel or stainless steel bearings Some sizes have special features such as serrations or small barbs (noted in description). Unground ends Ideal for axles in robotic applications and educational projects
|
Shim | |
Shim - Plastic (Relevance 5/10)
Easy to cut - colour coded - plastic shim sheets.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester.
|
Spacers | |
Spacers - Round - Hobby (Relevance 5/10)
Inexpensive nylon spacers for hobby applications
|
Spacers - Round - Through Bore - Nylon (Relevance 5/10)
Shaft spacers - Nylon
|
Splined Shafts and Bushes | |
Splined Shafts (Relevance 5/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Stepper Motors | |
Motors - Stepper - Basic Hobby (Relevance 5/10)
Small light weight stepper motor for your hobby or light duty projects
|
Storage | |
Parts Boxes - Clear Plastic (Relevance 5/10)
Fischer Plastics clear compartmented parts boxes with flip lids.
Plastic hinged lid. Quality catch to secure contents. Ideal for storing small parts.
|
Parts Boxes - Grey Plastic (Relevance 5/10)
Fischer Plastics grey parts boxes with adjustable dividers and open top.
Open top. Fits most standard shelving. Ideal for storing small parts. Dividers can be removed, added or adjusted. Comes with dividers to make number of compartments shown - but additional dividers can be purchased.
|
Tools | |
Hobby Tools - General (Relevance 5/10)
Flywheel Rench, Allen Key Set, Socket Driver Se, 4-way cross wrench, pioin stocker, ball end pliers, side cutters, long nose pliers, flat nose pliers, pinion storage, hobby scissors and body reamer.
See main listings for sizes not shown here.
|
Universal Joints | |
Universal Joints - Plastic (Relevance 5/10)
Acetal with or without steel inserts.
|
Wheels | |
Wheels - Hobby - General (Relevance 5/10)
Includes wheels for robots and general hobby applications
Also see tracks for Robotic applications
|
Balls | |
Balls - Acetal (Relevance 4/10)
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
|
Balls - Nylon (Relevance 4/10)
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
|
Batteries | |
Batteries - Hobby - Kick Start (Relevance 4/10)
Kick start battery for your glow plugs.
|
Batteries - Hobby - Lead Acid (Relevance 4/10)
All types of Lead Acid Battery
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Thrust | |
Bearings - Thrust - Plastic - Self Seating (Relevance 4/10)
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 4/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Books and DVD | |
Books - Hobby - General (Relevance 4/10)
Tips and tricks, maintenance and how-to guides.
|
Books - Hobby - Mousetrap Vehicles (Relevance 4/10)
Tips and tricks and how-to guides for Mousetrap powered cars and boats
|
Books - Hobby - RC Car and Truck (Relevance 4/10)
Tips and tricks, maintenance and how-to guides.
|
Books - Hobby - RC Planes (Relevance 4/10)
Tips and tricks, maintenance and how-to guides.
|
Hobby DVD (Relevance 4/10)
Note! DVD's are formatted for Zone 4 Australasia.
|
Fasteners | |
Bushings - Panel (Relevance 4/10)
|
Nuts - Hexagonal - Nylon (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Nylon (Relevance 4/10)
|
Roll Pins - Hobby (Relevance 4/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Screws - Machine - Nylon (Relevance 4/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - Nylon - Countersunk Head (Relevance 4/10)
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Socket - Cap - Nylon (Relevance 4/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 4/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Plastic with Knurl (Relevance 4/10)
Brass threaded insert Knurled circumference to assist with grip
|
Knobs - Pointer - Aluminium and Plastic (Relevance 4/10)
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
|
Knobs - Star - Female - Plastic (Relevance 4/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Knobs - Star - Male - Plastic (Relevance 4/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Hobby Accessories | |
Accessories - Servo Programmer - Digital HFP20 (Relevance 4/10)
Servo programmer-tester for Hitec digital servos
|
Crystals - Remote Control (Relevance 4/10)
|
Dubro Accessories Listed by Description (Relevance 4/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Glow Plugs (Relevance 4/10)
Real McCoy, OS glow plugs and Super Tiger
|
Glow Starter Kits (Relevance 4/10)
Starter pack. Fuel Bottel, 4 in 1 spanner, glow starter and charger
|
Glow Starters (Relevance 4/10)
|
Gyros - Hobby (Relevance 4/10)
Hitec and more
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Leads and Connectors - Hobby (Relevance 4/10)
Adaptor leads for batteries, battery chargers, servos and receivers including Tamiya, Deans and Losi plugs.
Includes Deans and T Connectors
|
Propeller Hubs (Relevance 4/10)
|
Propellers - Boat (Relevance 4/10)
|
Propellers - Plane - Electric - Folding (Relevance 4/10)
|
Propellers - Plane - Electric - Slow Fly (Relevance 4/10)
|
Propellers - Plane - Electric - Standard (Relevance 4/10)
|
Propellers - Plane - Nitro - 2 Blade (Relevance 4/10)
|
Propellers - Plane - Nitro - 3 Blade (Relevance 4/10)
|
Propellers - Plane - Nitro - 4 Blade (Relevance 4/10)
|
Receivers and Accessories (Relevance 4/10)
Receivers for Radio Control Equipment - Spektrum and Futaba
|
Speed Controllers - Aircraft (Relevance 4/10)
|
Speed Controllers - Car and Buggy (Relevance 4/10)
|
Speed Controllers - Marine (Relevance 4/10)
|
Spinners - 2 Blade (Relevance 4/10)
Spinners for aircraft propellers
|
Spinners - 3 Blade (Relevance 4/10)
Spinners for aircraft propellers
|
Tape - Double Sided (Relevance 4/10)
Double Sided Foam Tape
|
Tape - Glass Fibre (Relevance 4/10)
Hinge tape and other uses
|
Wire - Silicone (Relevance 4/10)
Silicone Wire in various colours and gauges
|
Hobby Condensed Selection | |
Hobby Gears - Spur - Module 0.4 (Relevance 4/10)
A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.
|
Hobby Gears - Spur - Module 0.5 (Relevance 4/10)
A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.
|
Hobby Washers - Precision Shim (Relevance 4/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Pillow Block - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 4/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Materials | |
Rod - Round - Nylon (Relevance 4/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Motors - Hobby | |
Motors - Hobby - Brushed (Relevance 4/10)
|
Motors - Hobby - Brushless (Relevance 4/10)
|
Motors - Hobby - Brushless Packages (Relevance 4/10)
Brushless Systems including Motor and Electronic Speed Controller
|
Motors - Hobby - Rock Crawler (Relevance 4/10)
For slow moving rock crawlers. Motors only - speed controllers not included.
|
Motors - Hobby - Robotic - Appliances | |
Motors - DC 6mm Diameter (Relevance 4/10)
Our smallest motors at an affordable price.
Various models 10000 to 30000 rpm Low starting voltage of <0.8V Rated Voltage 1.3V 100 hours / 100000 turns mechanical life Less than 43 dB Mechanical Noise Level
|
Motors - DC 12.3X24.4 mm (Relevance 4/10)
M-300C Series 0.5 to 6 VDC - 1820 to 2700 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx. 22 grams.
|
Motors - DC 16.6X32.0 mm (Relevance 4/10)
M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 18.9X18.0X9.5 mm (Relevance 4/10)
M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams.
|
Motors - DC 20.0X25.0 mm (Relevance 4/10)
1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts
|
Motors - DC 23.6X25.0 mm (Relevance 4/10)
1.5 to 4.5 VDC - 12,500 RPM unloaded at 4.5 volts
|
Motors - DC 25.0X21.0 mm (Relevance 4/10)
M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 25.0x20.1X15.1 mm (Relevance 4/10)
M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X23.8 mm (Relevance 4/10)
M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X24.2X18.3 mm (Relevance 4/10)
MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 27.6X51.0 mm (Relevance 4/10)
Compact, high torque and reliable 16,200 RPM unloaded at 6 volts
|
Motors - DC 30.5X24.2 mm (Relevance 4/10)
M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 30.5X24.2X18.3 mm (Relevance 4/10)
MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 36.0X71.0 mm (Relevance 4/10)
High power, high speed 11,800 RPM unloaded at 12 volts
|
Motors - DC 42.0X78.0 mm (Relevance 4/10)
High power, high speed 18,800 to 20,000 RPM unloaded 6 volts to 12 volts
|
Motors - DC 42.0X85.0 mm (Relevance 4/10)
High power, high speed 9,700 RPM unloaded at 12 volts
|
Mounts and Vibration Control | |
Dampeners - Bushings - Silicone (Relevance 4/10)
Protects fragile subjects from micro-vibrations and light shocks.
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
|
Plain Bearings | |
Bushings - Spherical - Steel (Relevance 4/10)
Steel
Compensates for axial loads and misalignment.
|
Pulleys | |
Pulleys - U Groove - Plastic (Relevance 4/10)
Acetal Body with Brass Insert.
|
Reels | |
Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 4/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Remote Control Aircraft | |
Micro Foam Plane - Hobby Zone (Relevance 4/10)
Indoor and Outdoor
Brands Include: Champ
|
Rod Ends | |
Rod Ends - Plastic (Relevance 4/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Servo Motors | |
Servomotors - Hobby - General (Relevance 4/10)
For cars, planes, boats and helicopters. JR, Spektrum, Futaba and Hitec
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Spacers | |
Spacers - Hex - Threaded - Nylon (Relevance 4/10)
Threaded Hex Spacers.
|
Splined Shafts and Bushes | |
Splined Bushes - Unflanged (Relevance 4/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Storage | |
Enclosures - Plastic ABS (Relevance 4/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Made with ABS Material, moulded in dark grey. Bosses on internal base allow fixing of PCBs horizontally, or connection of terminals, etc. The lid and base incorporate a tongue and groove sealing system with a neoprene gasket. Lid fixing screws are M4 stainless steel (non-metallic) into threaded brass inserts. Designed to IP65 of IEC529 and NEMS 4 (dust and hoseproof).
|
Universal Joints | |
Universal Joints - Plastic with Brass Inserts - Ondrives (Relevance 4/10)
Cross Piece and Inserts: Brass CZ121 Chromate and passivate finish. Body - Black Acetal Max Speed: 1000 Rpm. Temp. Range: -20 Deg C to +60 Deg C. Backlash Free up to 1000,000,000 Turns.
|
|
