Categories that include the terms: BUSHES and PLASTIC and IGLIDUR and G and UNFLANGED
|
Plain Bearings |  |
Bushes - Plastic - Iglidur G - Flanged (Relevance 10/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Iglidur G - Unflanged (Relevance 10/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Natural Nylon - Unflanged (Relevance 9/10)
Nominal clearance on ID. Nominal oversize on OD for push-fit in housing. Pricing is highly quantity dependant. Please enquire.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 9/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 6/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Plastic - Ertalyte TX (Relevance 6/10)
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
|
Bushes - Plastic - Hobby (Relevance 6/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 6/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushings - Spherical - Plastic (Relevance 6/10)
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
|
Splined Shafts and Bushes | |
Splined Bushes - Unflanged (Relevance 6/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Balls | |
Balls - Acetal (Relevance 4/10)
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
|
Balls - Bored - Plastic (Relevance 4/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Nylon (Relevance 4/10)
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 4/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 4/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Thrust | |
Bearings - Thrust - Plastic - Self Seating (Relevance 4/10)
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 4/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Fasteners | |
Bushings - Panel (Relevance 4/10)
|
Joints - Clevis - Plastic (Relevance 4/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Nuts - Dome - Nylon (Relevance 4/10)
Natural Nylon.
|
Nuts - Hexagonal - Nylon (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 4/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 4/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Nylon (Relevance 4/10)
|
Screws - Hex Head - Plastic (Relevance 4/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Self Tapping - For Plastics (Relevance 4/10)
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics Be sure to select correct screw for hard or soft plastic threadcutting
|
Socket Set Screws - Acetal Tipped (Relevance 4/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Nylon Tipped (Relevance 4/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Threaded Rod - Allthread - Plastic (Relevance 4/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Handles and Knobs | |
Knobs - Star - Female - Plastic (Relevance 4/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Knobs - Star - Male - Plastic (Relevance 4/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Hobby Condensed Selection | |
Hobby Gears - Worm and Wheel 40 : 1 Plastic (Relevance 4/10)
Popular Hobby Set
1 start 40 tooth gear.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 4/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Insert Bearings and Housings | |
Bearings - For Plastic Housings (Relevance 4/10)
Ideal for wet conditions. Includes Acetal and Stainless grades 316 and 440C
Load and speed calculations are for reference only. Testing is recommended.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Pillow Block - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 4/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Materials | |
Rod - Round - Acetal (Relevance 4/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Nylon (Relevance 4/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Mounts and Vibration Control | |
Dampeners - Bushings - Silicone (Relevance 4/10)
Protects fragile subjects from micro-vibrations and light shocks.
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
|
Plain Bearings | |
Bushes - Aluminium - Frelon Lined (Relevance 4/10)
Self lubricating - Replaces oilite or plastic bearings.
SLIP FIT: Housing bore should be OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be OD -0.000/+0.010. Use freezing method for press fit assembly - freeze bearing to -18 Deg C for 30 minutes. Body: Aluminium. Lining: Frelon.
|
Bushes - Bronze - Hobby (Relevance 4/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Sintered - Flanged (Relevance 4/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Solid - C92300 (Relevance 4/10)
Solid Precision C93200 bronze bushes.
ID Tolerance : -0.0254 / +0.0254 OD Tolerance : +0.0762 LENGTH Tolerance : -0.127 / +0.127. Composition (Approx.) : Copper 83%, Tin 6.7%, Zinc 3%, Lead 7% and small traces of Aluminum, Antimony, Iron, Nickel, Phosphorus, Silcon and Sulpher.
|
Bushes - Bronze - Solid - LG2 (Relevance 4/10)
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Spherical - Sintered (Relevance 4/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Bushes - Steel - PTFE Lined - Split (Relevance 4/10)
Similar style to Glacier™ bushes.
|
Bushings - Spherical - Steel (Relevance 4/10)
Steel
Compensates for axial loads and misalignment.
|
Pulleys | |
Pulleys - U Groove - Plastic (Relevance 4/10)
Acetal Body with Brass Insert.
|
Reels | |
Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 4/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Rod Ends | |
Rod Ends - Plastic (Relevance 4/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Roller Chain and Sprockets | |
Chain - Roller - Plastic - Simplex (Relevance 4/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Rollers | |
Rollers - Nylon Tyre (Relevance 4/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Shim | |
Shim - Plastic (Relevance 4/10)
Easy to cut - colour coded - plastic shim sheets.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester.
|
Spacers | |
Spacers - Round - Through Bore - Nylon (Relevance 4/10)
Shaft spacers - Nylon
|
Splined Shafts and Bushes | |
Splined Shafts (Relevance 4/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Storage | |
Enclosures - Plastic ABS (Relevance 4/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Made with ABS Material, moulded in dark grey. Bosses on internal base allow fixing of PCBs horizontally, or connection of terminals, etc. The lid and base incorporate a tongue and groove sealing system with a neoprene gasket. Lid fixing screws are M4 stainless steel (non-metallic) into threaded brass inserts. Designed to IP65 of IEC529 and NEMS 4 (dust and hoseproof).
|
Parts Boxes - Clear Plastic (Relevance 4/10)
Fischer Plastics clear compartmented parts boxes with flip lids.
Plastic hinged lid. Quality catch to secure contents. Ideal for storing small parts.
|
Parts Boxes - Grey Plastic (Relevance 4/10)
Fischer Plastics grey parts boxes with adjustable dividers and open top.
Open top. Fits most standard shelving. Ideal for storing small parts. Dividers can be removed, added or adjusted. Comes with dividers to make number of compartments shown - but additional dividers can be purchased.
|
Universal Joints | |
Universal Joints - Plastic (Relevance 4/10)
Acetal with or without steel inserts.
|
Universal Joints - Plastic with Brass Inserts - Ondrives (Relevance 4/10)
Cross Piece and Inserts: Brass CZ121 Chromate and passivate finish. Body - Black Acetal Max Speed: 1000 Rpm. Temp. Range: -20 Deg C to +60 Deg C. Backlash Free up to 1000,000,000 Turns.
|
Washers | |
Washers - Disc Spring - Plastic (Relevance 4/10)
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
|
Worms and Worm Gears | |
Worm Gears - 24 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 2) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 2) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 4/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 2) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 2) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 4/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Adhesives and Sealants | |
Retaining Compounds (Relevance 3/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Super Bonders (Relevance 3/10)
Mercury, ZAP, Molytec, Loctite, Pacer, Pro Seal. Cyanoacrylate adhesives for quick bonding. Products for foam Kicker, wood, metals, rubber and plastics.
Some items in this category are marked as only available for collection.
|
Bearings | |
Bearings - High Speed Cage (Relevance 3/10)
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
Bearings in this listing have various types of high speed cages. Speed ratings range from 20 percent to 80 percent increase on standard cage types. Please contact us for a data sheet on the specific size you require.
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 3/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 3/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 3/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Fasteners | |
Screws - Machine - Nylon (Relevance 3/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - Nylon - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Socket - Cap - Nylon (Relevance 3/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Gearmotors | |
Gearmotors - Basic - Hobby Kits (Relevance 3/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gears and Gearing | |
Gears - Mitre - 16 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 24 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 32 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 48 Pitch (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass, carbon steel and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Brass and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.6 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 32 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 48 Pitch - 14.5 Degree (Relevance 3/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Flexible (Relevance 3/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Gears - Racks - Flexible - Guide Rails (Relevance 3/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Gears - Racks - Module 0.4 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.5 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.8 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1.25 (Relevance 3/10)
20 Degree Pressure Angle. Acetal.
Plastic.
|
Gears - Racks - Module 1.5 (Relevance 3/10)
20 Degree Pressure Angle. Carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 2 (Relevance 3/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 3 (Relevance 3/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - 16 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 16 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 3/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 64 Pitch (Relevance 3/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 3/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.4 (Relevance 3/10)
PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 (Relevance 3/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 - Hobby - Economy (Relevance 3/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle - POM Plastic
Plastic Only Inexpensive for hobby and toy use No locking mechanisms
|
Gears - Spur - Module 0.7 (Relevance 3/10)
PCD = No. of Teeth x 0.700mm. 20 Degree Pressure Angle. Acetal.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.8 (Relevance 3/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 3/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.25 (Relevance 3/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.5 (Relevance 3/10)
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
|
