Categories that include the terms: BUSHES and STEEL and PTFE and LINED and SPLIT
|
Plain Bearings |  |
Bushes - Steel - PTFE Lined - Split (Relevance 10/10)
Similar style to Glacier™ bushes.
|
Rod Ends | |
Rod Ends - Steel - PTFE Lined (Relevance 8/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Plain Bearings | |
Bushings - Spherical - Steel (Relevance 6/10)
Steel
Compensates for axial loads and misalignment.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 6/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Plain Bearings | |
Bushes - Aluminium - Frelon Lined (Relevance 5/10)
Self lubricating - Replaces oilite or plastic bearings.
SLIP FIT: Housing bore should be OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be OD -0.000/+0.010. Use freezing method for press fit assembly - freeze bearing to -18 Deg C for 30 minutes. Body: Aluminium. Lining: Frelon.
|
Balls | |
Balls - Bored - Steel (Relevance 4/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Balls - Chrome Steel (Relevance 4/10)
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
|
Balls - Stainless Steel - 316L Grade (Relevance 4/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 4/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 4/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Clamping and Locking | |
Clamps - Gear - Split (Relevance 4/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Fasteners | |
Joints - Clevis - Steel (Relevance 4/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Nuts - Cap - Stainless Steel (Relevance 4/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 4/10)
Stainless Steel.
|
Nuts - Dome - Steel (Relevance 4/10)
Mild Steel, chrome and zinc plated
|
Pins - Cotter - Stainless Steel (Relevance 4/10)
Split pins.
|
Screws - Machine - Stainless Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Cap - Alloy Steel (Relevance 4/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Threaded Rod - Allthread - Steel (Relevance 4/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Insert Bearings and Housings | |
Bearings - For Pressed Metal Housings (Relevance 4/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Linear Drive Systems - Leadscrew | |
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Materials | |
Wire - Steel - Spring - Music Wire (Relevance 4/10)
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 4/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Sintered - Flanged (Relevance 4/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 4/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Solid - C92300 (Relevance 4/10)
Solid Precision C93200 bronze bushes.
ID Tolerance : -0.0254 / +0.0254 OD Tolerance : +0.0762 LENGTH Tolerance : -0.127 / +0.127. Composition (Approx.) : Copper 83%, Tin 6.7%, Zinc 3%, Lead 7% and small traces of Aluminum, Antimony, Iron, Nickel, Phosphorus, Silcon and Sulpher.
|
Bushes - Bronze - Solid - LG2 (Relevance 4/10)
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Spherical - Sintered (Relevance 4/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 4/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 4/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Pulleys | |
Pulleys - U Groove - Steel (Relevance 4/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 4/10)
301 S11/S22 Stainless Steel.
|
Snaprings - Internal - Stainless Steel (Relevance 4/10)
301 S11/S22 Stainless Steel.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 4/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 4/10)
High tensile steel.
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 4/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Rollers | |
Rollers - Steel (Relevance 4/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Shim | |
Shim and Foil - Steel (Relevance 4/10)
Shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Silver Steel | |
Shafting - Ground - Precision (Relevance 4/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Spacers | |
Spacers - Round - Through Bore - Stainless Steel (Relevance 4/10)
Shaft spacers - Stainless Steel
|
Spacers - Round - Through Bore - Steel (Relevance 4/10)
Shaft spacers - Steel
|
Splined Shafts and Bushes | |
Splined Bushes - Unflanged (Relevance 4/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Splined Shafts (Relevance 4/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Universal Joints | |
Universal Joints - Steel (Relevance 4/10)
Steel - Cast Zinc - Stainless Steel.
|
Washers | |
Washers - Cup - Stainless Steel (Relevance 4/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 4/10)
Flat Carbon Spring Steel Washers.
|
Balls | |
Balls - PTFE (Relevance 3/10)
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 Deg C. Unpolished. Specific Gravity: 2.3.
|
Balls - Stainless Steel - 304 Grade (Relevance 3/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 3/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Fasteners | |
Bushings - Panel (Relevance 3/10)
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 3/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 3/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Stainless Steel (Relevance 3/10)
304 and 316 Stainless Wing Nuts
|
Nuts - Wing - Steel (Relevance 3/10)
Zinc Plated Wing Nuts
|
Pins - Clevis - Stainless Steel 304 (Relevance 3/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 3/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Dowel - Standard - Hardened Steel (Relevance 3/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 3/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 3/10)
304 and 420 grades DIN1481.
|
Screws - Hex Head - Steel (Relevance 3/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Alloy Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Frelon Lined (Relevance 3/10)
Self aligning. Open or closed. Precision or standard. For rotating and linear motion.
|
Keys and Keysteel | |
Keys - Gib Head - Steel (Relevance 3/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Keys - Woodruff (Relevance 3/10)
Stainless steel and carbon steel
|
Linear Motion Bearings | |
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 3/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Materials | |
Hexagonal Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rod - Round - PTFE (Relevance 3/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Stainless Steel (Relevance 3/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Square Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Tube - Round - Stainless Steel (Relevance 3/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Mounts and Vibration Control | |
Dampeners - Bushings - Silicone (Relevance 3/10)
Protects fragile subjects from micro-vibrations and light shocks.
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
|
Plain Bearings | |
Bushes - Plastic - Ertalyte TX (Relevance 3/10)
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
|
Bushes - Plastic - Hobby (Relevance 3/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Plastic - Iglidur G - Flanged (Relevance 3/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Iglidur G - Unflanged (Relevance 3/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Natural Nylon - Unflanged (Relevance 3/10)
Nominal clearance on ID. Nominal oversize on OD for push-fit in housing. Pricing is highly quantity dependant. Please enquire.
|
Bushings - Spherical - Plastic (Relevance 3/10)
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
|
Reels | |
Reels - Spring Powered - Base Mounted - Steel (Relevance 3/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 3/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 3/10)
|
Shim | |
Shim and Foil - Stainless Steel (Relevance 3/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Spacers | |
Spacers - Hex - Threaded - Stainless Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Washers | |
Washers - Disc Spring - Carbon Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Disc Spring - Stainless Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Mild Steel (Relevance 3/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - PTFE (Relevance 3/10)
Teflon Washers
|
Washers - Flat - Stainless Steel - Commercial (Relevance 3/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 3/10)
Precision Tolerances.
|
Washers - Lock - External Tooth - Spring Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Split (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Adhesives and Sealants | |
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Retaining Compounds (Relevance 1/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Batteries | |
Batteries - Hobby - NiMH (Relevance 1/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 1/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Ball - Single Row - Radial - Flanged (Relevance 1/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 1/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ceramic Hybrid (Relevance 1/10)
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
|
Bearings - Ceramic Si3N4 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 1/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Housings - Bearing - Pillow Block - Miniature (Relevance 1/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 1/10)
Stainless steel ball type cam followers.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Collars - Shaft - Gripfast (Relevance 1/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Standard (Relevance 1/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Clutches - Slip - Inline (Relevance 1/10)
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
|
Couplings | |
Couplings - Double Disk (Relevance 1/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
Couplings - Double Disk - High Torque (Relevance 1/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - Slit Type (Relevance 1/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Fasteners | |
Inserts - Keensert (Relevance 1/10)
Stainless Steel 303. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.
|
Inserts - Thread Repair (Relevance 1/10)
Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Inserts - Thread Repair - Assortments (Relevance 1/10)
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Inserts - Thread Repair - Kits (Relevance 1/10)
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Joints - Ball and Socket - Right Angle (Relevance 1/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
|
