Categories that include the terms: CAM and FOLLOWERS and ROLLER and TYPE and MINIATURE and STANDARD
|
Cam Followers |  |
Cam Followers - Miniature - Standard (Relevance 10/10)
Stainless steel ball type cam followers.
|
Cam Followers - Roller Type - Stainless Steel (Relevance 10/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Urethane Covered (Relevance 9/10)
Urethane tyred cam followers for noise reduction, reduced wear and non marking
|
Rollers | |
Rollers - Yoke - Cam (Relevance 5/10)
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking
Polycoated shore 80A cast urethane cover
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Cage Type (Relevance 4/10)
Cage and Rollers.
|
Bearings - Needle Roller - Shell Type (Relevance 4/10)
Light Weight. Compact Design.
|
Batteries | |
Batteries - Coin Type (Relevance 3/10)
Coin type batteries to suit watches, clocks, computers and other equipment. Lithium, Silver Oxide and Alkaline
|
Batteries - Standard (Relevance 3/10)
The Venom standard non-rechargeable battery range includes AA, AAA, C, D and 9V non-rechargeable.
Bulk packs and single cards
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 3/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Inner Rings (Relevance 3/10)
Hardened sleeves for needle roller bearings.
|
Bearings - Needle Roller - Machined - With Inner Ring (Relevance 3/10)
|
Bearings - Needle Roller - Machined - Without Inner Ring (Relevance 3/10)
|
Bearings - Specialty | |
Bearings - Automotive - Tapered Roller (Relevance 3/10)
|
Bearings - One Way - Roller (Relevance 3/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 3/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Bearings and Housings | |
Bearings - Press - Needle Roller - Flange Mounted (Relevance 3/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Housings - Bearing - Pillow Block - Miniature (Relevance 3/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Cams | |
Cams (Relevance 3/10)
|
Cams - Adjustable (Relevance 3/10)
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 3/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 3/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Collars - Shaft - Clamp Type (Relevance 3/10)
|
Collars - Shaft - Standard (Relevance 3/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Shaftloc-tm Simple Type M (Relevance 3/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Couplings | |
Couplings - Helical - Standard (Relevance 3/10)
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Couplings - Jaw Type - With Polyurethane Spider (Relevance 3/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Couplings - Jaw Type - With Rubber Spider (Relevance 3/10)
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Couplings - Slit Type (Relevance 3/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Fasteners | |
Pins - Dowel - Standard - Hardened Steel (Relevance 3/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 3/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Taper - Imperial - Miniature (Relevance 3/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Miniature sizes. Stainless and Mild Steel.
|
Pins - Taper - Imperial - Standard (Relevance 3/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Socket Set Screws - Cup Point - Standard (Relevance 3/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Handles and Knobs | |
Knobs - Pointer - 18T Spline Type (Relevance 3/10)
Push on suits 18 tooth splined 6.35mm (1/4 inch) shaft.
|
Hobby Accessories | |
Propellers - Plane - Electric - Standard (Relevance 3/10)
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Square - Miniature (Relevance 3/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Housing - Base Type (Relevance 3/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Bush Type (Relevance 3/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 3/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Materials | |
Rod - Round - Bronze - LG2 (Standard) (Relevance 3/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 3/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Mounts and Vibration Control | |
Mounts - Leveling - Base Type - Round (Relevance 3/10)
For loads of 45 to 5350 kg.
|
Suspension Units - Rubber - Square - Insert Type (Relevance 3/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Paint | |
Paints - Standard Spray - Tamiya (Relevance 3/10)
Cans of spray paint suitable for painting static models.
Tamiya spray colours provide an impressive finish to static models. When painting figures with a brush, it can be difficult to get paint into creases such as on faces and fabric. Using spray paint is a sure way to get a smooth, even finish. They are also extremely useful for painting large surfaces. Each can contains 100ml of paint, which is enough to fully cover 2 or 3, 1/24 scale sized car bodies. The paint is a synthetic lacquer that cures in a short period of time. Tamiya spray paints are not affected by acrylic or enamel paints. Therefore, following the painting of the entire assembly, details can be added or picked out using enamel and/or acrylic paints. By combining three different paints, the decoration of plastic models will become simpler and more effective.
|
Retaining Rings and Clips | |
Circlips - External - Basic (Standard) (Relevance 3/10)
Imperial and metric DIN471 / N1400 / D1460.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 3/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 3/10)
High tensile steel.
|
Chain - Roller - Metal - Simplex (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Plastic - Simplex (Relevance 3/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 3/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 3/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 3/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 3/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Sprockets - Idler (Relevance 3/10)
Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Rollers | |
Bearings - Pressure Roller - With Urethane OD (Relevance 3/10)
Bearings with Urethane Tyre on OD for applications requiring frictional movement.
For applications including paper and card dispensing and rolling (eg ATM Machines).
|
Rollers - Idler - Stainless Steel (Relevance 3/10)
|
Rollers - Idler - With Aluminium Sleeve (Relevance 3/10)
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
|
Rollers - Idler - With Sintered Bearing (Relevance 3/10)
|
Rollers - Nylon Tyre (Relevance 3/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Rollers - Steel (Relevance 3/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Rollers - Track - With Inner Race (Relevance 3/10)
|
Rollers - Urethane Feed - With Hub (Relevance 3/10)
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter Sleeve - Aluminium
|
Rope and Cable | |
Cable - Miniature - Coated (Relevance 3/10)
Lengths will be supplied continuous to a maximum of 3mtrs (ie, 10 x 300mm supplied as 3mtr length)
Recommended that nylon coating is stripped prior to swaging. Sold per length. Multiple quantities will be supplied in a continuous length up to 3mtr maximum.
|
Springs | |
Spring Assemblies - Small Bracket - RINO (Relevance 3/10)
Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
|
Springs - Compression - Standard (Relevance 3/10)
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
|
Storage | |
Parts Boxes - Tilt Type (Relevance 3/10)
Tilt pak plastic carry box with 4 self locking drawers
Can be joined togetherto make a double sided case Freestanding or mountable 4 self locking drawers each with 4 compartments
|
Tools | |
Tools - Pullers - Small (Relevance 3/10)
Small pullers for miniature bearings, gears, pulleys, sprockets and other pressed on parts.
|
Washers | |
Washers - Flat - Commercial - All Types (Relevance 3/10)
Includes all materials listed in other commercial washer categories.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Precision - All Types (Relevance 3/10)
Includes all materials listed in other precision washer categories.
|
Adhesives and Sealants | |
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Stainless Steel - 316L Grade (Relevance 1/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Batteries | |
Batteries - Hobby - Lead Acid (Relevance 1/10)
All types of Lead Acid Battery
|
Batteries - Hobby - Lipo (Relevance 1/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom, Hacker. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - NiMH (Relevance 1/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - Nicad (Relevance 1/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Economy (Relevance 1/10)
Taiwanese Hobby Bearings - Inexpensive Option. The type you find at most hobby shops.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - High Speed Cage (Relevance 1/10)
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
Bearings in this listing have various types of high speed cages. Speed ratings range from 20 percent to 80 percent increase on standard cage types. Please contact us for a data sheet on the specific size you require.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 1/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 1/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 1/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Belts | |
Belts - Timing - 1.000mm Pitch (Relevance 1/10)
Miniature 1mm series timing belts
Pitch (P) - 1.000mm Tooth Height (H) - 0.41mm. Belt Height (W) - 0.97mm Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.032mm Pitch - MXL (Relevance 1/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.073mm Pitch - 40DP (Relevance 1/10)
Standard Series Timing Belts 2.072mm or 0.08016 inch pitch.
Pitch (P) - 2.073mm (0.0816 inch). Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 1/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 9.525mm Pitch - L (Relevance 1/10)
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Pitch (P) - 9.525mm (0.200 inch). Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
|
Belts - Vee - 5.0 x 3.0 mm (Relevance 1/10)
Miniature and small belts. 5.0mm Top Width x 3.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.0 x 4.0 mm - Y (Relevance 1/10)
Miniature and small belts. 6.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.4 x 4.1 mm - 2L (Relevance 1/10)
Miniature and small belts. 6.4mm Top Width x 4.1mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 8.0 x 4.0 mm (Relevance 1/10)
Miniature and small belts. 8.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 9.7 x 8.0 mm - SPZ (Relevance 1/10)
Miniature and small belts. 9.7mm Top Width x 8.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 5.5 mm - M/3L (Relevance 1/10)
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 6.0 mm - Z (Relevance 1/10)
Miniature and small belts. 10.0mm Top Width x 6.0mm Height.
Sizes are nominal and may vary slightly.
|
Books and DVD | |
Books - Engineering (Relevance 1/10)
Machinery handbook contains standards, materials and other general engineering information.
|
Castors | |
Ball Transfer Units - Heavy Duty (Relevance 1/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Screw Stem (Relevance 1/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Castors - Black Rubber (Relevance 1/10)
Black rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Castors - Blue Non Marking Rubber (Relevance 1/10)
Blue non-marking rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Clamping and Locking | |
Clamps - Gear - Split (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Couplings | |
Extenders - Shaft (Relevance 1/10)
Miniature and large shaft extenders.
|
Fasteners | |
Joints - Ball and Socket - Right Angle (Relevance 1/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Roll Pins - Hobby (Relevance 1/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Screws - Machine - Brass - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Self Tapping - Pan Head (Relevance 1/10)
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
|
Gearboxes | |
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 1/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 1/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 1/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Solarbotics Gearmotors (Relevance 1/10)
Hobby gearmotors for all types of applications
|
Gears and Gearing | |
Gears - Racks - Flexible (Relevance 1/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels (Relevance 1/10)
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
|
Dual Vee - Guide Wheels - Studded (Relevance 1/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Dual Vee - Tracks with Mounting Holes (Relevance 1/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 1/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Handles and Knobs | |
Knobs - Ball - Knock On - Phenolic (Relevance 1/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Knobs - Precision - Knurled (Relevance 1/10)
Set screw and clamp types - Stainless Steel. Also known as Thumb Knobs.
303 Stainless Steel. ID Tolerance +0.013 / -0.000 mm (+0.0005 / - 0.0000 inch).
|
Knobs - Thumb - For Cap Screws (Relevance 1/10)
Four Types and four colours to fit onto Socket Head Cap Screws.
To fit Socket Head Cap Screws (Order Separately - See link at base of listing below). Choice of 4 Colours. Choice of 4 styles. Made From Acetal Resin.
|
Knobs - Thumb - With Cap Screw (Relevance 1/10)
Four types and four colours.
Complete with high tensile alloy steel screw. If stainless steel screws required please order cap screws separately and knobs without screw.
|
Hobby Accessories | |
Accessories - Hobby - Body Clips (Relevance 1/10)
Large and small body clips. Fluoro or standard. Plastic coated or anodised. Range of colours. Bent and straight.
|
Speed Controllers - Aircraft (Relevance 1/10)
|
Speed Controllers - Car and Buggy (Relevance 1/10)
|
Speed Controllers - Marine (Relevance 1/10)
|
Hobby Condensed Selection | |
Hobby Gears - Spur - 48DP (Relevance 1/10)
A small selection of popular 48DP Plastic/ Metal Pinion and Spur gears
See main listings under Gears for sizes not listed here To work out the pitch diameter of a 48DP spur gear, divide multiply the no of teeth by 0.52917.
|
Hobby Gears - Spur - Module 0.4 (Relevance 1/10)
A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.
|
Hobby Gears - Spur - Module 0.5 (Relevance 1/10)
A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.
|
Hobby Washers - Precision Shim (Relevance 1/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Ladder Chain and Sprockets | |
Chain - Ladder - 6.350mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
Chain - Ladder - 9.525mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Housing - Flanged (Relevance 1/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 1/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Lubricants | |
Lubricants - General (Relevance 1/10)
Various brands and types. Includes Inox, Lanox, Anti-Seize, Cutting Fluid, Chain Lube, Moly Lube, Food Grade, PTFE Lubes, Silicone and more
Some items in this category are marked as only available for collection. Includes high temperature and food grade lubes. Battery Conditioner - Oils - Moisture Inhibitor - WD - Valve and Oring Lubricant
|
Magnets | |
Magnets - Ferrite (Relevance 1/10)
Small ferrite magnets with good pulling strength.
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
|
