Categories that include the terms: CLAMPS and SYNCRO and L and SHAPED
|
Clamping and Locking |  |
Clamps - Syncro - L-Shaped (Relevance 9/10)
|
Belts | |
Belts - Timing - 9.525mm Pitch - L (Relevance 4/10)
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Pitch (P) - 9.525mm (0.200 inch). Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 4/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 4/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Collars - Shaft - Clamp Type (Relevance 4/10)
|
Levers | |
Levers - Clamp (Relevance 4/10)
Steel Parts: Quality class 5.8. Handle: Diecast zinc to DIN 1743 or Glass fibre reinforced plastic with toothed wheel in diecast zinc. Surface Finish: Handle plastic coated. Steel parts black oxide finish.
|
Levers - Clamp - Quick Release (Relevance 4/10)
Handles: Die-cast zinc or plastic. Internal thread: mechanism made from carbon steel. The thru-hole clamping lever allows for quick clamping on long thread lengths.
|
Pulleys | |
Pulleys - Timing - 9.525mm Pitch - L (Relevance 4/10)
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Various materials as shown.
|
Adhesives and Sealants | |
Adhesives - Dope (Relevance 3/10)
|
Adhesives - Fishing (Relevance 3/10)
|
Adhesives - General (Relevance 3/10)
Molytec, Loctite, Pacer, Dow Corning, 3M. Includes silicone sealant, gasket adhesive, canopy glue, belt conditioner and electronic tak-pak.
Some items in this category are marked as only available for collection.
|
Epoxies (Relevance 3/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Retaining Compounds (Relevance 3/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Solder (Relevance 3/10)
|
Super Bonders (Relevance 3/10)
Mercury, ZAP, Molytec, Loctite, Pacer, Pro Seal. Cyanoacrylate adhesives for quick bonding. Products for foam Kicker, wood, metals, rubber and plastics.
Some items in this category are marked as only available for collection.
|
Threadlockers (Relevance 3/10)
ZAP, Molytec, Loctite, Pacer. Pipe sealant, low to high strength threadlockers. Hydraulic threadlocker. Wick-In. Stops threads loosening from vibration.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Acetal (Relevance 3/10)
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
|
Balls - Acrylic (Relevance 3/10)
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically +/- 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
|
Balls - Bored - Plastic (Relevance 3/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Bored - Steel (Relevance 3/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Balls - Ceramic - Silicon Nitride (Relevance 3/10)
Outstanding wear resistance. Good thermal and chemical resistance.
High hardness. High strength over a wide temperature range. High fracture toughness. Outstanding wear resistance. Good thermal and chemical resistance.
|
Balls - Chrome Steel (Relevance 3/10)
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
|
Balls - Nylon (Relevance 3/10)
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
|
Balls - PTFE (Relevance 3/10)
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 Deg C. Unpolished. Specific Gravity: 2.3.
|
Balls - Phosphor Bronze (Relevance 3/10)
Specific Gravity 8.4
|
Balls - Polypropylene (Relevance 3/10)
Excellent for liquid level float applications.
Tolerance and spherecity: up to and including 25.4mm diameter = +/-0.0508mm, over 25.4mm diameter +/-0.0762mm. Very resistant to most acids and alkalies. Excellent for liquid level float applications. Unpolished. Specific Gravity: 0.91.
|
Balls - Ruby - Synthetic (Relevance 3/10)
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Specific Gravity: 3.98.
|
Balls - Sapphire - Synthetic (Relevance 3/10)
Extreme hardness, wear resistance, non-corrosiveness and chemical inertness.
Tolerances available on request. Specific Gravity: 3.98. Grade 25. Extreme hardness, wear resistance, non-corrosiveness and chemical inertness. High mechanical strength. Transparent (refractive index 1.76).
|
Balls - Stainless Steel - 304 Grade (Relevance 3/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 3/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 3/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 3/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Balls - Tungsten Carbide (Relevance 3/10)
Extreme hardness and wear resistance.
Tolerances available on request. Precision Grade: Grade 25. Hardness: Rockwell A: 91.5 (Approx 77 Rockwell C). Extreme hardness and wear resistance. Specific Gravity: 14.95.
|
Batteries | |
Batteries - Hobby - Lead Acid (Relevance 3/10)
All types of Lead Acid Battery
|
Batteries - Hobby - Lipo (Relevance 3/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom, Hacker. Some have Tamiya or Deans Connectors.
|
Batteries - Holders (Relevance 3/10)
Battery holders for AAA, AA, C, D and 9 Volt
|
Batteries - Rechargeable - Home and Industry (Relevance 3/10)
Rechargeable Industrial Batteries
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 3/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Ball - Single Row - Radial - Economy (Relevance 3/10)
Taiwanese Hobby Bearings - Inexpensive Option. The type you find at most hobby shops.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Flanged (Relevance 3/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 3/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 3/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Bearings - Grooved | |
Bearings - U Groove Profile OD (Relevance 3/10)
Special OD Bearings.
Contact us for tolerances.
|
Bearings - V Groove Profile OD (Relevance 3/10)
Special OD Bearings.
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Cage Type (Relevance 3/10)
Cage and Rollers.
|
Bearings - Needle Roller - Inner Rings (Relevance 3/10)
Hardened sleeves for needle roller bearings.
|
Bearings - Needle Roller - Machined - With Inner Ring (Relevance 3/10)
|
Bearings - Needle Roller - Machined - Without Inner Ring (Relevance 3/10)
|
Bearings - Needle Roller - Shell Type (Relevance 3/10)
Light Weight. Compact Design.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 3/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 3/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Automotive - Tapered Roller (Relevance 3/10)
|
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 3/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ceramic Hybrid (Relevance 3/10)
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
|
Bearings - Ceramic Si3N4 (Relevance 3/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 3/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - One Way - Roller (Relevance 3/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings - Pivot - Flanged (Relevance 3/10)
|
Bearings - Pivot - With Inner Ring (Relevance 3/10)
Note! Minimum quantities apply to production of these items.
|
Bearings - Pivot - Without Inner Ring (Relevance 3/10)
Note! Minimum quantities apply to production of these items.
|
Bearings - Unground (Relevance 3/10)
Unground bearings used in trolleys, prams and wheel barrow wheels
|
Model Jet Turbine Bearings (Relevance 3/10)
Bearings developed specifically for use in Model Jet turbines.
These bearings are designed for high speeds usually between 80,000 and 120,000 RPM in short runs. Speeds over 120,000 are often obtainable. Testing is required. High Temperature up to 300 Degrees Celsius. Bearing Type R in the tables indicates Radial (refer our main bearings category).
|
Bearings - Thrust | |
Bearings - Thrust - Ball (Relevance 3/10)
3 Piece Thrust Bearings, Shielded and Unshielded.
|
Bearings - Thrust - Ball - Banded (Relevance 3/10)
|
Bearings - Thrust - Plastic - Self Seating (Relevance 3/10)
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
|
Bearings - Thrust - Roller (Relevance 3/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Lazy Susan Bearings (Relevance 3/10)
One unit construction for maximum stability and quiet running.
Centre opening allows for a centre post if required.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 3/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 3/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 3/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 3/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 3/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 3/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 3/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 3/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 3/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Housings - Bearing - Pillow Block - Miniature (Relevance 3/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Belt and Sprockets - Posi-Drive | |
Belts - Posi-Drive - 3.75 mm Circular Pitch - Double Core (Relevance 3/10)
Same as US 0.1475 Pitch - Use with Posi-Drive Sprockets.
Use Double Core with Posi-Drive Sprockets. 3.746mm Circular Pitch. Same as US 0.1475 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Belts - Posi-Drive - 4.00 mm Circular Pitch - Double Core (Relevance 3/10)
Same as US 20 Pitch - Use with Posi-Drive Sprockets.
Use Double Core with Posi-Drive Sprockets. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core (Relevance 3/10)
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Sprockets - Posi-Drive - 3.75 mm Circular Pitch (Relevance 3/10)
Same as US 0.1475 Pitch - Use with Double Core Belts.
Use with Double Core Posi-Drive Belts. 3.746mm Circular Pitch. Same as US 0.1475 Pitch.
|
Sprockets - Posi-Drive - 4.00 mm Circular Pitch (Relevance 3/10)
Same as US 20 Pitch - Use with Double Core Belts.
Use with Double Core Posi-Drive Belts. 3.990mm Circular Pitch. Same as US 20 Pitch.
|
Belts | |
Belt Tension Tester (Relevance 3/10)
For testing the tension on assembled timing belts, vee belts, flat belts etc.
Gauges for testing all types of belts when assembled for correct tension.
|
Belts - Flat (Relevance 3/10)
Working Tension 2.3 to 27.5 N. Length Tolerance +/- 0.5%. Breaking Strength 1108 N. 1 Ply Polyester Woven Cord, Black Neoprene Coating. Maximum Belt Speed: 5000 mtrs / min (20000 feet / min).
|
Belts - Rounthane (Relevance 3/10)
Joinable belting.
Join with Rounthane Connectors. Material : Non Slip Polyurethane. Use with grooved idler pulleys or 6.35mm Top Width V Pulleys. Purchased per 305mm (1 foot). Orders for more than 1 foot will be supplied as a continuous length.
|
Belts - Rounthane - Connectors (Relevance 3/10)
Joinable belting connectors.
|
Belts - Timing - 1.000mm Pitch (Relevance 3/10)
Miniature 1mm series timing belts
Pitch (P) - 1.000mm Tooth Height (H) - 0.41mm. Belt Height (W) - 0.97mm Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 3mm Wide (Relevance 3/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 6mm Wide (Relevance 3/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 9mm Wide (Relevance 3/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.032mm Pitch - MXL (Relevance 3/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.073mm Pitch - 40DP (Relevance 3/10)
Standard Series Timing Belts 2.072mm or 0.08016 inch pitch.
Pitch (P) - 2.073mm (0.0816 inch). Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.500mm Pitch - T2.5 (Relevance 3/10)
T Series Metric Timing Belts.
Pitch (P) - 2.500mm. Tooth Length (T) - 1.50mm. Tooth Height (H) - 0.70mm. Belt Height (W) - 1.30mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 6mm Wide (Relevance 3/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 9mm Wide (Relevance 3/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - HTD (Relevance 3/10)
HTD Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.22mm. Belt Height (W) - 2.41mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - GT - TRUE METRIC (Relevance 3/10)
GT Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - HTD (Relevance 3/10)
HTD Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - T5 (Relevance 3/10)
T Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.20mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 3/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - Lengths (Relevance 3/10)
Sold per meter - Refer diagrams in timing belt listings for aspects of various pitches.
Lengths of timing belt stock are used for reciprocating applications. Not meant to be joined.
|
Belts - Vee - 5.0 x 3.0 mm (Relevance 3/10)
Miniature and small belts. 5.0mm Top Width x 3.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.0 x 4.0 mm - Y (Relevance 3/10)
Miniature and small belts. 6.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.4 x 4.1 mm - 2L (Relevance 3/10)
Miniature and small belts. 6.4mm Top Width x 4.1mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 8.0 x 4.0 mm (Relevance 3/10)
Miniature and small belts. 8.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 9.7 x 8.0 mm - SPZ (Relevance 3/10)
Miniature and small belts. 9.7mm Top Width x 8.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 5.5 mm - M/3L (Relevance 3/10)
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 6.0 mm - Z (Relevance 3/10)
Miniature and small belts. 10.0mm Top Width x 6.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.5 x 9.0 mm - A/4L (Relevance 3/10)
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.7 x 10.0 mm - SPA (Relevance 3/10)
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.3 x 13.0 mm - SPB (Relevance 3/10)
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.5 x 11.0 mm - B/5L (Relevance 3/10)
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 31.5 x 19.0 mm - D (Relevance 3/10)
31.5mm Top Width x 19.0mm Height.
Sizes are nominal and may vary slightly.
|
Books and DVD | |
Books - Engineering (Relevance 3/10)
Machinery handbook contains standards, materials and other general engineering information.
|
Books - Hobby - General (Relevance 3/10)
Tips and tricks, maintenance and how-to guides.
|
Books - Hobby - Mousetrap Vehicles (Relevance 3/10)
Tips and tricks and how-to guides for Mousetrap powered cars and boats
|
Books - Hobby - RC Car and Truck (Relevance 3/10)
Tips and tricks, maintenance and how-to guides.
|
Books - Hobby - RC Planes (Relevance 3/10)
Tips and tricks, maintenance and how-to guides.
|
Books - Robotics (Relevance 3/10)
Tips and tricks, maintenance and how-to guides. Includes industrial and hobby robotics.
|
Hobby DVD (Relevance 3/10)
Note! DVD's are formatted for Zone 4 Australasia.
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 3/10)
Stainless steel ball type cam followers.
|
Cam Followers - Roller Type - Stainless Steel (Relevance 3/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Urethane Covered (Relevance 3/10)
Urethane tyred cam followers for noise reduction, reduced wear and non marking
|
Cams | |
Cams - Adjustable (Relevance 3/10)
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 3/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Heavy Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Screw Stem (Relevance 3/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Castors - Black Rubber (Relevance 3/10)
Black rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Castors - Blue Non Marking Rubber (Relevance 3/10)
Blue non-marking rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Castors - Plate - General Purpose - Ball Bearing - Light Medium Duty (Relevance 3/10)
|
Castors - Plate - General Purpose - Light Duty (Relevance 3/10)
|
Clamping and Locking | |
Collars - Shaft - Fairloc (Relevance 3/10)
|
Collars - Shaft - Gripfast (Relevance 3/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Standard (Relevance 3/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Collars - Shaft - With Integral Shim (Relevance 3/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Hubs - Bolt On (Relevance 3/10)
Aluminium Hub with Set Screws
|
Insulators - Screw (Relevance 3/10)
Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.
|
Reducers - Bore (Relevance 3/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Rings - Tolerance (Relevance 3/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Shaftloc-tm Simple Type M (Relevance 3/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 3/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Cleaning | |
Cleaning Products - Miscellaneous (Relevance 3/10)
Products related to bearing and power transmission work. No overseas sales.
Some items in this category are marked as only available for collection.
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 3/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Clutches - Slip - Inline (Relevance 3/10)
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
|
Computer Software | |
Flight Simulator Software (Relevance 3/10)
Phoenix - Ikarus brand Flight simulator software with and with Handcontroller packs
|
Couplings | |
Couplings - Bantam - Complete (Relevance 3/10)
Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm.
Parallel Offset 0.25 mm. Angular Offset 1.5 Degree.
|
Couplings - Bellows - Set Screw - Aluminium (Relevance 3/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Couplings - Double Disk (Relevance 3/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
|
