Categories that include the terms: COUPLINGS and BELLOWS and INTEGRAL and CLAMP and 316 and STAINLESS
|
Balls |  |
Balls - Stainless Steel - 316 Grade (Relevance 4/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 4/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Couplings | |
Couplings - Bellows - Set Screw - Aluminium (Relevance 4/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Fasteners | |
Pins - Clevis - Stainless Steel 316 (Relevance 4/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Balls | |
Balls - Stainless Steel - 304 Grade (Relevance 3/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 440C Grade (Relevance 3/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 3/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 3/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 3/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 3/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Syncro - L-Shaped (Relevance 3/10)
|
Collars - Shaft - Clamp Type (Relevance 3/10)
|
Collars - Shaft - Standard (Relevance 3/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Collars - Shaft - With Integral Shim (Relevance 3/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Couplings | |
Couplings - Bantam - Complete (Relevance 3/10)
Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm.
Parallel Offset 0.25 mm. Angular Offset 1.5 Degree.
|
Couplings - Double Disk (Relevance 3/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
Couplings - Double Disk - High Torque (Relevance 3/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - HRC (Relevance 3/10)
|
Couplings - Helical - Standard (Relevance 3/10)
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Couplings - Jaw Type - With Polyurethane Spider (Relevance 3/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Couplings - Jaw Type - With Rubber Spider (Relevance 3/10)
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Couplings - Rigid (Relevance 3/10)
0.35 to 5.1 Nm.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.
|
Couplings - Slit Type (Relevance 3/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Extenders - Shaft (Relevance 3/10)
Miniature and large shaft extenders.
|
Fasteners | |
Nuts - Cap - Stainless Steel (Relevance 3/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 3/10)
Stainless Steel.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 3/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Stainless Steel (Relevance 3/10)
304 and 316 Stainless Wing Nuts
|
Pins - Clevis - Stainless Steel 304 (Relevance 3/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Stainless Steel (Relevance 3/10)
Split pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 3/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 3/10)
304 and 420 grades DIN1481.
|
Screws - Machine - Stainless Steel (Relevance 3/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Stainless (Relevance 3/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Die Cast (Relevance 3/10)
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
|
Housings - Bearing - Blocks - Frelon Lined (Relevance 3/10)
Self aligning. Open or closed. Precision or standard. For rotating and linear motion.
|
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 3/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Housings - Bearing - Blocks - Thermoplastic (Relevance 3/10)
Iglide L280 / Igus W300 Ball with Thermoplatic Body.
Maintenance Free, Lightweight, Self-Lubricating. Compensates for alignment errors. Temperature Range -40 deg C to +130 deg C. Max. Static Tensile Strength is Long Term. Info for Short Term also available.
|
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Housings - Bearing - Flanged - Square - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing : Igumid G. Ball : Highly wear resistant Iglidur W300.
|
Levers | |
Levers - Clamp (Relevance 3/10)
Steel Parts: Quality class 5.8. Handle: Diecast zinc to DIN 1743 or Glass fibre reinforced plastic with toothed wheel in diecast zinc. Surface Finish: Handle plastic coated. Steel parts black oxide finish.
|
Levers - Clamp - Quick Release (Relevance 3/10)
Handles: Die-cast zinc or plastic. Internal thread: mechanism made from carbon steel. The thru-hole clamping lever allows for quick clamping on long thread lengths.
|
Materials | |
Hexagonal Bar - 303 Stainless (Relevance 3/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rod - Round - Stainless Steel (Relevance 3/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Square Bar - 303 Stainless (Relevance 3/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Tube - Round - Stainless Steel (Relevance 3/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 3/10)
301 S11/S22 Stainless Steel.
|
Snaprings - Internal - Stainless Steel (Relevance 3/10)
301 S11/S22 Stainless Steel.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 3/10)
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 3/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Shaft and Shafting | |
Shafts - Flexible - Coupling Ends - Open (SDP) (Relevance 3/10)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
|
Shim | |
Shim and Foil - Stainless Steel (Relevance 3/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Spacers | |
Spacers - Hex - Threaded - Stainless Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Round - Through Bore - Stainless Steel (Relevance 3/10)
Shaft spacers - Stainless Steel
|
Washers | |
Washers - Cup - Stainless Steel (Relevance 3/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Disc Spring - Stainless Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Stainless Steel - Commercial (Relevance 3/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 3/10)
Precision Tolerances.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Flanged (Relevance 1/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings and Housings | |
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 1/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Housings - Bearing - Pillow Block - Miniature (Relevance 1/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 1/10)
Stainless steel ball type cam followers.
|
Clamping and Locking | |
Collars - Shaft - Fairloc (Relevance 1/10)
|
Collars - Shaft - Gripfast (Relevance 1/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Hubs - Bolt On (Relevance 1/10)
Aluminium Hub with Set Screws
|
Insulators - Screw (Relevance 1/10)
Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.
|
Reducers - Bore (Relevance 1/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Rings - Tolerance (Relevance 1/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Fasteners | |
Nuts - Flange - Serrated (Relevance 1/10)
Stainless Steel.
|
Pins - Taper - Imperial - Miniature (Relevance 1/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Miniature sizes. Stainless and Mild Steel.
|
Pins - Taper - Imperial - Standard (Relevance 1/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Screws - Shoulder - Socket Head (Relevance 1/10)
Includes stainless steel and alloy steel
|
Screws - Socket - Countersunk - Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Thumb - Plain (Relevance 1/10)
Brass, steel, aluminum and stainless and nylon.
|
Socket Set Screws - Cup Point - Standard (Relevance 1/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Gears and Gearing | |
Gears - Internal - 24 Pitch (Relevance 1/10)
Various materials including 2024-T4 Aluminum, 303 stainless steel and brass.
|
Gears - Internal - Module 0.5 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 0.8 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 1 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Mitre - Module 0.6 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 20 Degree (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 64 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 72 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 96 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 120 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - Module 0.5 (Relevance 1/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.75 (Relevance 1/10)
20 Degree Pressure Angle. Brass and stainless steel.
Metallic.
|
Gears - Racks - Module 0.8 (Relevance 1/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1 (Relevance 1/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1.5 (Relevance 1/10)
20 Degree Pressure Angle. Carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 24 Pitch - Stem (Relevance 1/10)
303 stainless steel.
Metallic.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 64 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch - Differential End (Relevance 1/10)
To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel.
Metallic.
|
Gears - Spur - 72 Pitch - Stem (Relevance 1/10)
303 stainless steel.
Metallic.
|
Gears - Spur - Module 0.4 (Relevance 1/10)
PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 (Relevance 1/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.75 - Stem (Relevance 1/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 0.8 (Relevance 1/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 1/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 - Stem (Relevance 1/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 1.25 (Relevance 1/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.5 (Relevance 1/10)
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2 (Relevance 1/10)
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2.5 (Relevance 1/10)
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 3 (Relevance 1/10)
PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears and Gearing - Antibacklash | |
Gears - Spur - Antibacklash - 32 Pitch (Relevance 1/10)
Steel - Stainless Steel - Aluminium - 20 Degree Pressure Angle.
|
Gears and Gearing - Matched Sets | |
Gears - Mitre - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets - 1:1 Ratio. Stainless steel and aluminium.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90 degree angle.
|
Handles and Knobs | |
Knobs - Precision - Knurled (Relevance 1/10)
Set screw and clamp types - Stainless Steel. Also known as Thumb Knobs.
303 Stainless Steel. ID Tolerance +0.013 / -0.000 mm (+0.0005 / - 0.0000 inch).
|
Insert Bearings and Housings | |
Bearings - For Plastic Housings (Relevance 1/10)
Ideal for wet conditions. Includes Acetal and Stainless grades 316 and 440C
Load and speed calculations are for reference only. Testing is recommended.
|
Keys and Keysteel | |
Keys - Woodruff (Relevance 1/10)
Stainless steel and carbon steel
|
Ladder Chain and Sprockets | |
Chain - Ladder - 3.750mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 4.242mm Pitch - Size 21 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 4.699mm Pitch - Size 19 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 6.350mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
Chain - Ladder - 7.264mm Pitch - Size 18 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 9.525mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 1/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Pulleys | |
Pulleys - U Groove - Steel (Relevance 1/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Retaining Rings and Clips | |
Spiral Rings - External - Heavy Duty (Relevance 1/10)
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2
|
Spiral Rings - Internal - Heavy Duty (Relevance 1/10)
Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2
|
Spiral Rings - Internal - Medium Duty (Relevance 1/10)
Includes AI / WH / AS3217 / RR / MIL-R-27426B1 - Spring Steel and Stainless Steel.
Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AI, Smalley: WH, Spirolox and Ramsey: RR, Aerospace AS3217, MIL-R-27426B1
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 1/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
|
