Categories that include the terms: DAMPERS and ROTARY and 50 and TO and 400 and NCM
|
Belt and Sprockets - Posi-Drive |  |
Belts - Posi-Drive - 4.00 mm Circular Pitch - Double Core (Relevance 3/10)
Same as US 20 Pitch - Use with Posi-Drive Sprockets.
Use Double Core with Posi-Drive Sprockets. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core (Relevance 3/10)
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Sprockets - Posi-Drive - 4.00 mm Circular Pitch (Relevance 3/10)
Same as US 20 Pitch - Use with Double Core Belts.
Use with Double Core Posi-Drive Belts. 3.990mm Circular Pitch. Same as US 20 Pitch.
|
Belts | |
Belts - Vee - 5.0 x 3.0 mm (Relevance 3/10)
Miniature and small belts. 5.0mm Top Width x 3.0mm Height.
Sizes are nominal and may vary slightly.
|
Electrical | |
Adaptors - Power - AC to DC - Multi Plug (Relevance 3/10)
SAA Approved Australian Adaptors for AC to DC. Supplied with assorted plugs.
|
Gearboxes | |
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 3/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 3/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 3/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - DC - Size 37/350 Low Cost (Relevance 3/10)
37mm Gearhead Body Diameter. Low cost. 160 RPM Output Speed. One model only. Reversible.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Single Assembly (Relevance 3/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Single Assembly - Circlip Retained (Relevance 3/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Square - Miniature (Relevance 3/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Motors - Hobby - Robotic - Appliances | |
Motors - DC 20.0X25.0 mm (Relevance 3/10)
1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts
|
Motors - DC 23.6X25.0 mm (Relevance 3/10)
1.5 to 4.5 VDC - 12,500 RPM unloaded at 4.5 volts
|
Motors - DC 25.0X21.0 mm (Relevance 3/10)
M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 25.0x20.1X15.1 mm (Relevance 3/10)
M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 42.0X85.0 mm (Relevance 3/10)
High power, high speed 9,700 RPM unloaded at 12 volts
|
Mounts and Vibration Control | |
Mounts - Cylindrical - Female to Blank (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Female to Female (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Blank (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Female (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Male (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Pulleys | |
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 3mm Wide Belts (Relevance 3/10)
Timing Pulleys to suit GT 2mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 6mm Wide Belts (Relevance 3/10)
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide.
Various materials as shown.
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 9mm Wide Belts (Relevance 3/10)
Timing Pulleys to suit 2mm Pitch GT Timing Belts 9mm Wide.
Aluminium Alloy
|
Pulleys - Timing - 2.500mm Pitch - T2.5 - STOCK (Relevance 3/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 3.000mm Pitch - GT - To Suit 6mm Wide Belts (Relevance 3/10)
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 6mm Wide.
Various materials as shown.
|
Pulleys - Timing - 3.000mm Pitch - GT - To Suit 9mm Wide Belts (Relevance 3/10)
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 9mm Wide.
Various materials as shown.
|
Pulleys - Timing - 5.000mm Pitch - HTD - STOCK (Relevance 3/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 5.080mm Pitch - XL - STOCK (Relevance 3/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Unsorted | |
Himoto Miscellaneous Parts to Sort (Relevance 3/10)
Miscellaneous Parts to Sort
|
Oreillys Miscellaneous Parts to Sort (Relevance 3/10)
Miscellaneous Parts to Sort
|
Adhesives and Sealants | |
Threadlockers (Relevance 1/10)
ZAP, Molytec, Loctite, Pacer. Pipe sealant, low to high strength threadlockers. Hydraulic threadlocker. Wick-In. Stops threads loosening from vibration.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Acetal (Relevance 1/10)
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
|
Balls - Acrylic (Relevance 1/10)
Resistance to weather and sunlight. Good abrasion resistance.
Diametrical tolerances typically +/- 0.08 or 0.13 mm depending on size. Acrylic (Methyl Methacrylate). Resistance to weather and sunlight. Good abrasion resistance. Water clear transparent. Polished. Ground and Polished.
|
Balls - PTFE (Relevance 1/10)
No water absorption. Temperatures up to 288 Deg C.
Tolerances available on request. Not affected by any known acids or alkalies. No water absorption. Temperatures up to 288 Deg C. Unpolished. Specific Gravity: 2.3.
|
Balls - Stainless Steel - 316 Grade (Relevance 1/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 1/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Batteries | |
Batteries - Coin Type (Relevance 1/10)
Coin type batteries to suit watches, clocks, computers and other equipment. Lithium, Silver Oxide and Alkaline
|
Bearings | |
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 1/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Bearings - Specialty | |
Bearings - Automotive - Tapered Roller (Relevance 1/10)
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 1/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Belts | |
Belts - Rounthane - Connectors (Relevance 1/10)
Joinable belting connectors.
|
Belts - Timing - 2.500mm Pitch - T2.5 (Relevance 1/10)
T Series Metric Timing Belts.
Pitch (P) - 2.500mm. Tooth Length (T) - 1.50mm. Tooth Height (H) - 0.70mm. Belt Height (W) - 1.30mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - GT - TRUE METRIC (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - HTD (Relevance 1/10)
HTD Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - T5 (Relevance 1/10)
T Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.20mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 1/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 1/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 1/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Heavy Duty (Relevance 1/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Screw Stem (Relevance 1/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Castors - Black Rubber (Relevance 1/10)
Black rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Castors - Blue Non Marking Rubber (Relevance 1/10)
Blue non-marking rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Castors - Plate - General Purpose - Ball Bearing - Light Medium Duty (Relevance 1/10)
|
Castors - Plate - General Purpose - Light Duty (Relevance 1/10)
|
Clamping and Locking | |
Insulators - Screw (Relevance 1/10)
Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.
|
Reducers - Bore (Relevance 1/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Rings - Tolerance (Relevance 1/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Cleaning | |
Cleaning Products - Miscellaneous (Relevance 1/10)
Products related to bearing and power transmission work. No overseas sales.
Some items in this category are marked as only available for collection.
|
Computer Software | |
Flight Simulator Software (Relevance 1/10)
Phoenix - Ikarus brand Flight simulator software with and with Handcontroller packs
|
Couplings | |
Couplings - Bantam - Complete (Relevance 1/10)
Isolates vibration up to 85%. Sleeve provides electrical insulation. 0.21Nm at 1725rpm.
Parallel Offset 0.25 mm. Angular Offset 1.5 Degree.
|
Couplings - Double Disk - High Torque (Relevance 1/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - Helical - Standard (Relevance 1/10)
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Couplings - Jaw Type - With Rubber Spider (Relevance 1/10)
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Couplings - Rigid (Relevance 1/10)
0.35 to 5.1 Nm.
Quality Class Precision: Bore Tolerance +0.013 / - 0.000 concentric within 0.0127mm T.I.R. Quality Class Commercial: Bore Tolerance +0.051 / -0.000.
|
Couplings - Slit Type (Relevance 1/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Dental Products | |
Tools - Dental Handpiece Repair (Relevance 1/10)
Tools for dental handpiece repair work.
|
Educational Projects | |
Kits - Mousetrap Powered Vehicles (Relevance 1/10)
These kits are designed to teach kids about physics.
|
Kits - Rubber Band Powered (Relevance 1/10)
These kits are designed to teach kids about physics.
|
Electrical | |
Solarbotics Capacitors (Relevance 1/10)
|
Solarbotics Chips - Voltage Detectors (Relevance 1/10)
The Panasonic 1381 series of voltage detectors activate at preset voltage levels.
|
Solarbotics Parts Bundles (Relevance 1/10)
Bundles of useful parts to assist with bicore experiments.
The large bundle includes a complete BEP board.
|
Engineering Sets | |
Toys - Educational - Meccano (Relevance 1/10)
Meccano construction toy sets help to teach children about mechanical systems
|
Engines | |
Engines - Aircraft - OS (Relevance 1/10)
Engines for model aircraft.
Nitro hobby engines.
|
Engines - Car and Buggy - Axial (Relevance 1/10)
Engines for model cars, buggies and truggies.
Nitro hobby engines.
|
Engines - Car and Buggy - Force (Relevance 1/10)
Engines for model cars, buggies and truggies.
Nitro hobby engines.
|
Engines - Steam - Wilesco (Relevance 1/10)
|
Engines - Steam - Wilesco - Accessories (Relevance 1/10)
|
Engines - Stirling - Wilesco (Relevance 1/10)
|
Fasteners | |
Pins - Dowel - Extractable (Relevance 1/10)
Hardened and Ground Steel 100 Cr6 to DIN 7979, m6 Dia. Tolerance.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Taper - Imperial - Standard (Relevance 1/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Screws - Machine - PEEK - Pan Head (Relevance 1/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Screws - Socket - Button - Alloy Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Aluminium (Relevance 1/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Zinc Plated (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Socket Set Screws - Acetal Tipped (Relevance 1/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Brass Tipped (Relevance 1/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Flat Ball Tip (Relevance 1/10)
Grub screws with a rotating flat tip. The ball can rotate up to 9 Deg. to fasten the object securely.
|
Socket Set Screws - Nylon Tipped (Relevance 1/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Solder Tipped (Relevance 1/10)
Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 1/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Gadgets | |
Mood Equipment (Relevance 1/10)
Laser lights and fog machines to create atmosphere and effects with model displays, films, parties or just for fun
|
Games | |
Games - Amusement (Relevance 1/10)
Fun inexpensive little gadgets and gizmos to keep the kids amused for hours
Lava drops, water snakes, pin art Voic changer, Juggling balls Magic eight ball
|
Gearboxes | |
Educational Gearbox Kits (Relevance 1/10)
Basic gearbox kits for prototyping, testing and learning
|
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 1/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 1/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 1/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 1/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - Basic - Hobby Kits (Relevance 1/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gearmotors - DC - Low Voltage (Relevance 1/10)
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel.
|
Gearmotors - DC - Size 12 (Relevance 1/10)
12mm Gearhead Body Diameter.
|
Gearmotors - DC - Size 20 Low Cost (Relevance 1/10)
20mm Gearhead Body Diameter. Low cost. 70 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 27 Low Cost (Relevance 1/10)
27mm Gearhead Body Diameter. Low cost. 36 RPM Output Speed. One model only. Reversible.
|
Gearmotors - Open Gear (Relevance 1/10)
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
|
Solarbotics Gearmotors (Relevance 1/10)
Hobby gearmotors for all types of applications
|
Gears and Gearing | |
Gears - Spur - 72 Pitch - Differential End (Relevance 1/10)
To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel.
Metallic.
|
Gears - Spur - Stock - 20 Pitch (Relevance 1/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears - Spur - Stock - 24 Pitch (Relevance 1/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears - Spur - Stock - Module 0.5 (Relevance 1/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears - Spur - Stock - Module 0.8 (Relevance 1/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears - Spur - Stock - Module 1 (Relevance 1/10)
Lengths of spur gear stock for manufacturing gears.
|
Handles and Knobs | |
Knobs - Knurled - Torque - Female (Relevance 1/10)
Plastic (high grade gloss black phenolic) Knob. Temperature Range: -30°C to +140°C.
|
Knobs - Knurled - Torque - Male (Relevance 1/10)
Plastic (high grade gloss black phenolic) Knob with Steel insert.
|
Knobs - Pointer - Arrow Top (Relevance 1/10)
Push on. Suits 6.35mm (1/4 inch) shaft.
|
Knobs - Thumb - For Cap Screws (Relevance 1/10)
Four Types and four colours to fit onto Socket Head Cap Screws.
To fit Socket Head Cap Screws (Order Separately - See link at base of listing below). Choice of 4 Colours. Choice of 4 styles. Made From Acetal Resin.
|
Hinges | |
Hinges - Flexi-Hinge - Precision (Relevance 1/10)
Double and Single Ended - Limited Angle Rotary Applications.
Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature.
|
Hobby Accessories | |
Leads and Connectors - Hobby (Relevance 1/10)
Adaptor leads for batteries, battery chargers, servos and receivers including Tamiya, Deans and Losi plugs.
Includes Deans and T Connectors
|
Hobby Condensed Selection | |
Hobby Gears - Spur - Module 0.4 (Relevance 1/10)
A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.
|
Hobby Gears - Spur - Module 0.5 (Relevance 1/10)
A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.
|
Kites | |
Kites - Delta - X (Relevance 1/10)
It's a breeze to launch in winds as light as 4mph and flys well in winds up to 20mph.
|
Ladder Chain and Sprockets | |
Chain - Ladder - 3.750mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 6.350mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
Sprockets - Ladder Chain - 3.750mm Pitch (Relevance 1/10)
With and without Hubs. Plastic and Steel.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Diameter (Relevance 1/10)
16mm Diameter with pitches 2.5 to 20mm. Machined or unmachined ends. Nuts sold seperately.
Material : Cf53 induction hardened to HRC 62 (=/- 2). Pitch accuracy : <= 0.1mm / 300mm ISO class 7. Nuts sold seperately.
|
Screws - Ball - Thomson Saginaw (Relevance 1/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Carriage Assembly (Relevance 1/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 1/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 1/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Magnets | |
Magnets - Rare Earth - Plated (Relevance 1/10)
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 Deg C to 93 Deg C. Size tolerances +/- 0.13
|
Materials | |
Balsa Wood - Block (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Dowel (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Leading Edge (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Rectangle (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Sheet (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Square (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Trailing Edge (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Balsa Wood - Triangle (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Plywood (Relevance 1/10)
Aircraft Grade. A $10.00 surcharge will apply to all orders of Plywood delivered.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery.
|
Rod - Round - Sintered Bronze (Relevance 1/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Solarbotics Materials (Relevance 1/10)
Versatile material for building robots because of its ability to glue well with epoxy and superglue.
Can be easily shaped by immersing in hot water and bending to your desired shape while it cools. Can be easily cut, drilled and threaded for screw fasteners. Do not use black Sintra with solar powered robots as it may get soft on hot days.
|
Spruce (Relevance 1/10)
Aircraft Grade. A $10.00 surcharge will apply to all orders of Spruce delivered.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery.
|
Model Kit Accessories | |
Model Kit Primers and Cleaners (Relevance 1/10)
For surface preparation prior to painting
|
|
