Categories that include the terms: DUAL and VEE and TRACKS and WITHOUT and MOUNTING and HOLES
|
Guide Rails - Tracks and Bearings |  |
Dual Vee - Tracks with Mounting Holes (Relevance 10/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 10/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Guide Wheels (Relevance 7/10)
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
|
Dual Vee - Guide Wheels - Studded (Relevance 7/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Machined - Without Inner Ring (Relevance 3/10)
|
Bearings - Specialty | |
Bearings - Pivot - Without Inner Ring (Relevance 3/10)
Note! Minimum quantities apply to production of these items.
|
Belts | |
Belts - Vee - 5.0 x 3.0 mm (Relevance 3/10)
Miniature and small belts. 5.0mm Top Width x 3.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.0 x 4.0 mm - Y (Relevance 3/10)
Miniature and small belts. 6.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.4 x 4.1 mm - 2L (Relevance 3/10)
Miniature and small belts. 6.4mm Top Width x 4.1mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 8.0 x 4.0 mm (Relevance 3/10)
Miniature and small belts. 8.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 9.7 x 8.0 mm - SPZ (Relevance 3/10)
Miniature and small belts. 9.7mm Top Width x 8.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 5.5 mm - M/3L (Relevance 3/10)
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 6.0 mm - Z (Relevance 3/10)
Miniature and small belts. 10.0mm Top Width x 6.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.5 x 9.0 mm - A/4L (Relevance 3/10)
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.7 x 10.0 mm - SPA (Relevance 3/10)
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.3 x 13.0 mm - SPB (Relevance 3/10)
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.5 x 11.0 mm - B/5L (Relevance 3/10)
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 31.5 x 19.0 mm - D (Relevance 3/10)
31.5mm Top Width x 19.0mm Height.
Sizes are nominal and may vary slightly.
|
Fasteners | |
Sleeves - Hex Hole (Relevance 3/10)
|
Sleeves - Square Hole - Plain (Relevance 3/10)
|
Gears and Gearing | |
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 3/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Housings with Integral Bearing | |
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 3/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Materials | |
Tube - Square - Carbon Fibre - Round Hole (Relevance 3/10)
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Tube - Square - Carbon Fibre - Square Hole (Relevance 3/10)
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Pulleys | |
Pulleys - Vee - A / 4L - Single Row - Through Bore (Relevance 3/10)
|
Pulleys - Vee - M / 3L - Single Row - Through Bore (Relevance 3/10)
|
Pulleys - Vee - Y / 2L - Single Row - Through Bore (Relevance 3/10)
|
Ratchets and Pawls | |
Ratchets - Without Hub (Relevance 3/10)
Match with pawls listed on this site.
|
Rollers | |
Rollers - Track - With Inner Race (Relevance 3/10)
|
Belts | |
Belt Tension Tester (Relevance 1/10)
For testing the tension on assembled timing belts, vee belts, flat belts etc.
Gauges for testing all types of belts when assembled for correct tension.
|
Fasteners | |
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Socket Set Screws - Rolling Ball Tip (Relevance 1/10)
Rolling ball tip for locating into a hole
|
Yoke Ends - Blank (Relevance 1/10)
Linkage Connectors with blank ends - no hole
Drop forged steel machined to SAE standards Also see clevis joints
|
Gears and Gearing | |
Gears - Racks - Flexible - Guide Rails (Relevance 1/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Handles and Knobs | |
Knobs - Oval Tapered - Press On - Phenolic (Relevance 1/10)
Press on knobs hold on securely without threads or set screws
Shaft diameter should be +0.000 / - 0.076 mm for best performance Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Die Cast (Relevance 1/10)
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
|
Ladder Chain and Sprockets | |
Sprockets - Ladder Chain - 3.750mm Pitch (Relevance 1/10)
With and without Hubs. Plastic and Steel.
|
Sprockets - Ladder Chain - 4.242mm Pitch - Size 21 (Relevance 1/10)
With and without Hubs. Plastic and Steel.
|
Sprockets - Ladder Chain - 7.264mm Pitch - Size 18 (Relevance 1/10)
With and without Hubs. Plastic and Steel.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Imperial - Acme (Relevance 1/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 1/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Mounts and Vibration Control | |
ISO-PAD - Sheets (Relevance 1/10)
For shimming and mounting machinery bases to isolate vibration.
Orange in colour. Patterned and unpatterned types. Tough vinyl chloride elastomeric resin bonded to both sides of a core of monofilament fibreglass. Co-efficient of friction 0.8. Temp range -35 Deg C to 110 Deg C.
|
Roller Chain and Sprockets | |
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 1/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 1/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 1/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 1/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Springs | |
Springs - Constant Force (Relevance 1/10)
Mounting hole specifications will be supplied on request. Free ID may vary to meet load specification.
|
Stepper Motors - Hybrid | |
Motors - Stepper - Hybrid - Nema Size 11 (Relevance 1/10)
Mounting hole centres 23.10 mm (+/- 0.2 mm) - Body Width 28.00 mm.
Refer PDF Link at bottm of internet page for sizes and wiring information. Hybrid Stepper Motors include a permanent magnet in the rotor.
|
Tools | |
Tools - Pin Wrench (Relevance 1/10)
Used on nuts with two holes.
Constructed of special blued steel.
|
Universal Joints | |
Universal Joints - Plastic (Relevance 1/10)
Acetal with or without steel inserts.
|
|
