Categories that include the terms: GEARBOXES and POWER and MOUNTING and FEET
|
Electrical |  |
Adaptors - Power - AC to DC - Multi Plug (Relevance 4/10)
SAA Approved Australian Adaptors for AC to DC. Supplied with assorted plugs.
|
Power Supplies (Relevance 4/10)
24 V DC.
Standard : 24V DC Output, 110V AC input. Available on special order : 12V DC Output, 220/230V AC input.
|
Gearboxes | |
Educational Gearbox Kits (Relevance 4/10)
Basic gearbox kits for prototyping, testing and learning
|
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 4/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 4/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 4/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 4/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 4/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 4/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 4/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 4/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - Basic - Hobby Kits (Relevance 4/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gearmotors - DC - Low Voltage (Relevance 4/10)
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel.
|
Gearmotors - DC - Size 12 (Relevance 4/10)
12mm Gearhead Body Diameter.
|
Gearmotors - DC - Size 20 Low Cost (Relevance 4/10)
20mm Gearhead Body Diameter. Low cost. 70 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 27 Low Cost (Relevance 4/10)
27mm Gearhead Body Diameter. Low cost. 36 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 37/350 Low Cost (Relevance 4/10)
37mm Gearhead Body Diameter. Low cost. 160 RPM Output Speed. One model only. Reversible.
|
Gearmotors - Open Gear (Relevance 4/10)
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
|
Solarbotics Gearmotors (Relevance 4/10)
Hobby gearmotors for all types of applications
|
Gears and Gearing | |
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 4/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 4/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 4/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Tracks with Mounting Holes (Relevance 4/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 4/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Tools | |
Bits - Power (Relevance 4/10)
Power bits for use with power screwdrivers and drills
|
Educational Projects | |
Kits - Mousetrap Powered Vehicles (Relevance 3/10)
These kits are designed to teach kids about physics.
|
Kits - Rubber Band Powered (Relevance 3/10)
These kits are designed to teach kids about physics.
|
Reels | |
Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 3/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Reels - Spring Powered - Base Mounted - Steel (Relevance 3/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 1/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Belts | |
Belts - Flat (Relevance 1/10)
Working Tension 2.3 to 27.5 N. Length Tolerance +/- 0.5%. Breaking Strength 1108 N. 1 Ply Polyester Woven Cord, Black Neoprene Coating. Maximum Belt Speed: 5000 mtrs / min (20000 feet / min).
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 1/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Clamping and Locking | |
Rings - Tolerance (Relevance 1/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Cleaning | |
Cleaning Products - Miscellaneous (Relevance 1/10)
Products related to bearing and power transmission work. No overseas sales.
Some items in this category are marked as only available for collection.
|
Fasteners | |
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Fuel | |
Fuel - Nitro - Aircraft (Relevance 1/10)
Note! Hobby Fuel cannot be sent by Australia Post.
Brands Include: Nitro X, Extra Blend, Sidewinder and Cool Power.
|
Fuel - Nitro - Car and Buggy (Relevance 1/10)
Note! Hobby Fuel cannot be sent by Australia Post.
Brands Include: Nitro X, Extra Blend, Sidewinder and Cool Power.
|
Fuel - Nitro - Helicopter (Relevance 1/10)
Note! Hobby Fuel cannot be sent by Australia Post.
Brands Include: Nitro X, Extra Blend, Sidewinder and Cool Power.
|
Fuel - Oil Mix (Relevance 1/10)
Note! Hobby Fuel is for collection at our counter only. Dangerous goods charges are too expensive for sending these goods out.
Oil mixes for blending with Nitro and Methanol. RC cars and helicopter fuels Includes Coolpower synthetic oil and first pressing Castor oil
|
Gears and Gearing | |
Gears - Bevel - 24 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 32 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 48 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.8 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 3 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Racks - Flexible - Guide Rails (Relevance 1/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Gears and Gearing - Matched Sets | |
Gears - Bevel - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets. For 90 degree angle power transfer.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. See Gears - Mitre for 1:1 ratios.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nut Flanges for Acme Nuts (Relevance 1/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 1/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Lubricants | |
Lubricants - Diff Gear Oil (Relevance 1/10)
Model Engines, Losi, ND Power Racing, Venom
|
Lubricants - Shock Oil (Relevance 1/10)
Model Engines, Losi, ND Power Racing, Venom
Viscosity is listed in Centistokes along with an approximate weight grade following in brackets.
|
Motors - Hobby - Robotic - Appliances | |
Motors - DC 36.0X71.0 mm (Relevance 1/10)
High power, high speed 11,800 RPM unloaded at 12 volts
|
Motors - DC 42.0X78.0 mm (Relevance 1/10)
High power, high speed 18,800 to 20,000 RPM unloaded 6 volts to 12 volts
|
Motors - DC 42.0X85.0 mm (Relevance 1/10)
High power, high speed 9,700 RPM unloaded at 12 volts
|
Mounts and Vibration Control | |
ISO-PAD - Sheets (Relevance 1/10)
For shimming and mounting machinery bases to isolate vibration.
Orange in colour. Patterned and unpatterned types. Tough vinyl chloride elastomeric resin bonded to both sides of a core of monofilament fibreglass. Co-efficient of friction 0.8. Temp range -35 Deg C to 110 Deg C.
|
Suspension Units - Rubber - Square - Insert Type (Relevance 1/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Solarbotics Kits | |
Solarbotics Kit 2 - Photopopper Photovore 4.2b (Relevance 1/10)
A very active solar powered robot. Educational build yourself kits.
Can cover up to a meter (3.3 feet) distance in under 2 minutes. Solar powered, light-sensing directional optics (eyes) and a pair of obstacle avoidance sensors. Directed phototropic or light-seeking behavior - traces outlines around shadows. Everything required is included (high-quality printed circuit board, optics, motors). 12 page instruction manual with over 26 illustrations and images.
|
Solarbotics Kit 5 - SolarSpeeder 1.1 (Relevance 1/10)
The SolarSpeeder 1.1 is a very quick Solaroller. Educational build yourself kits.
Can cover 3 meters (10 feet) in under 40 seconds in direct sunlight. Uses the same updated Solarengine technology found in the PhotoPopper 4.2 Photovore. About 60 mm long when assembled.
|
Springs | |
Springs - Constant Force (Relevance 1/10)
Mounting hole specifications will be supplied on request. Free ID may vary to meet load specification.
|
Stepper Motors - Hybrid | |
Motors - Stepper - Hybrid - Nema Size 11 (Relevance 1/10)
Mounting hole centres 23.10 mm (+/- 0.2 mm) - Body Width 28.00 mm.
Refer PDF Link at bottm of internet page for sizes and wiring information. Hybrid Stepper Motors include a permanent magnet in the rotor.
|
Storage | |
Enclosures - Aluminium - 100 Series (Relevance 1/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Internal guide slots for mounting PCB assemblies vertically. Ideal for housing sensitive electrical, mechanical, pneumatic or hydraulic devices Provides effective shielding of EMI and RFI. Designed to IP65 of IEC529 and NEMA 4 (dust and hoseproof). The lid incorporates a recessed neoprene gasket.
|
|
