Categories that include the terms: GEARBOXES and TEE and 700 and X and 700MM
|
Gearboxes |  |
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 6/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 6/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 5/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 5/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 5/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 5/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 5/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Belts | |
Belts - Vee - 5.0 x 3.0 mm (Relevance 4/10)
Miniature and small belts. 5.0mm Top Width x 3.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.0 x 4.0 mm - Y (Relevance 4/10)
Miniature and small belts. 6.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.4 x 4.1 mm - 2L (Relevance 4/10)
Miniature and small belts. 6.4mm Top Width x 4.1mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 8.0 x 4.0 mm (Relevance 4/10)
Miniature and small belts. 8.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 9.7 x 8.0 mm - SPZ (Relevance 4/10)
Miniature and small belts. 9.7mm Top Width x 8.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 5.5 mm - M/3L (Relevance 4/10)
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 6.0 mm - Z (Relevance 4/10)
Miniature and small belts. 10.0mm Top Width x 6.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.5 x 9.0 mm - A/4L (Relevance 4/10)
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.7 x 10.0 mm - SPA (Relevance 4/10)
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.3 x 13.0 mm - SPB (Relevance 4/10)
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.5 x 11.0 mm - B/5L (Relevance 4/10)
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 31.5 x 19.0 mm - D (Relevance 4/10)
31.5mm Top Width x 19.0mm Height.
Sizes are nominal and may vary slightly.
|
Gearboxes | |
Educational Gearbox Kits (Relevance 4/10)
Basic gearbox kits for prototyping, testing and learning
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 4/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - Basic - Hobby Kits (Relevance 4/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gearmotors - DC - Low Voltage (Relevance 4/10)
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel.
|
Gearmotors - DC - Size 12 (Relevance 4/10)
12mm Gearhead Body Diameter.
|
Gearmotors - DC - Size 20 Low Cost (Relevance 4/10)
20mm Gearhead Body Diameter. Low cost. 70 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 27 Low Cost (Relevance 4/10)
27mm Gearhead Body Diameter. Low cost. 36 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 37/350 Low Cost (Relevance 4/10)
37mm Gearhead Body Diameter. Low cost. 160 RPM Output Speed. One model only. Reversible.
|
Gearmotors - Open Gear (Relevance 4/10)
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
|
Solarbotics Gearmotors (Relevance 4/10)
Hobby gearmotors for all types of applications
|
Roller Chain and Sprockets | |
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 4/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 4/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Fasteners | |
Nuts - Hexagonal - Half - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 3/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 3/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Screws - Hex Head - Steel (Relevance 3/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Kites | |
Kites - Delta - X (Relevance 3/10)
It's a breeze to launch in winds as light as 4mph and flys well in winds up to 20mph.
|
Materials | |
Hexagonal Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 3/10)
301 S11/S22 Stainless Steel.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 3/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 3/10)
High tensile steel.
|
Chain - Roller - Metal - Simplex (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 3/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 3/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 3/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Spacers - Hex - Threaded - Stainless Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Washers | |
Washers - Lock - External Tooth - Spring Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Adhesives and Sealants | |
Adhesives - Dope (Relevance 1/10)
|
Adhesives - Fishing (Relevance 1/10)
|
Adhesives - General (Relevance 1/10)
Molytec, Loctite, Pacer, Dow Corning, 3M. Includes silicone sealant, gasket adhesive, canopy glue, belt conditioner and electronic tak-pak.
Some items in this category are marked as only available for collection.
|
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Retaining Compounds (Relevance 1/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Solder (Relevance 1/10)
|
Super Bonders (Relevance 1/10)
Mercury, ZAP, Molytec, Loctite, Pacer, Pro Seal. Cyanoacrylate adhesives for quick bonding. Products for foam Kicker, wood, metals, rubber and plastics.
Some items in this category are marked as only available for collection.
|
Threadlockers (Relevance 1/10)
ZAP, Molytec, Loctite, Pacer. Pipe sealant, low to high strength threadlockers. Hydraulic threadlocker. Wick-In. Stops threads loosening from vibration.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Bored - Steel (Relevance 1/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Balls - Chrome Steel (Relevance 1/10)
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
|
Balls - Stainless Steel - 304 Grade (Relevance 1/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 1/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 1/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 1/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 1/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings and Housings | |
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 1/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Belts | |
Belts - Timing - 2.032mm Pitch - MXL (Relevance 1/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 1/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 1/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Couplings | |
Extenders - Shaft (Relevance 1/10)
Miniature and large shaft extenders.
|
Engines | |
Engines - Car and Buggy - Axial (Relevance 1/10)
Engines for model cars, buggies and truggies.
Nitro hobby engines.
|
Fasteners | |
Inserts - Expansion (Relevance 1/10)
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
|
Joints - Clevis - Steel (Relevance 1/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Nuts - Blind (Relevance 1/10)
Blind nuts - Tee nuts.
|
Nuts - Cap - Stainless Steel (Relevance 1/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 1/10)
Stainless Steel.
|
Nuts - Dome - Steel (Relevance 1/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Aluminium (Relevance 1/10)
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Hexagonal - Brass (Relevance 1/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Hexagonal - Nylon (Relevance 1/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 1/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 1/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 1/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Titanium - CP Grade 1 (Relevance 1/10)
METRIC. CP Grade 1.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Nuts - Wing - Stainless Steel (Relevance 1/10)
304 and 316 Stainless Wing Nuts
|
Nuts - Wing - Steel (Relevance 1/10)
Zinc Plated Wing Nuts
|
Pins - Clevis - Stainless Steel 304 (Relevance 1/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 1/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Stainless Steel (Relevance 1/10)
Split pins.
|
Pins - Dowel - Extractable (Relevance 1/10)
Hardened and Ground Steel 100 Cr6 to DIN 7979, m6 Dia. Tolerance.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650
|
Pins - Dowel - Standard - Hardened Steel (Relevance 1/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 1/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Hitch - External (Relevance 1/10)
Also known as R-Clips.
|
Pins - Roll - Stainless Steel (Relevance 1/10)
304 and 420 grades DIN1481.
|
Pins - Taper - Metric - Extractable - Internal Thread (Relevance 1/10)
1:50 Taper.
DIN 7978. Mild Steel.
|
Screws - Hex Head - Plastic (Relevance 1/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Hex Head - Titanium Grade 1 (Relevance 1/10)
Fully threaded hex head screws (DIN933)
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Din 933.
|
Screws - Machine - Stainless Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Alloy Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Alloy Steel (Relevance 1/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Sleeves - Hex Hole (Relevance 1/10)
|
Threaded Rod - Allthread - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 1/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Fuel | |
Fuel - Nitro - Aircraft (Relevance 1/10)
Note! Hobby Fuel cannot be sent by Australia Post.
Brands Include: Nitro X, Extra Blend, Sidewinder and Cool Power.
|
Fuel - Nitro - Car and Buggy (Relevance 1/10)
Note! Hobby Fuel cannot be sent by Australia Post.
Brands Include: Nitro X, Extra Blend, Sidewinder and Cool Power.
|
Fuel - Nitro - Helicopter (Relevance 1/10)
Note! Hobby Fuel cannot be sent by Australia Post.
Brands Include: Nitro X, Extra Blend, Sidewinder and Cool Power.
|
Fuel - Oil Mix (Relevance 1/10)
Note! Hobby Fuel is for collection at our counter only. Dangerous goods charges are too expensive for sending these goods out.
Oil mixes for blending with Nitro and Methanol. RC cars and helicopter fuels Includes Coolpower synthetic oil and first pressing Castor oil
|
Gears and Gearing | |
Gears - Racks - Flexible (Relevance 1/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Gears - Racks - Flexible - Guide Rails (Relevance 1/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Gears - Spur - 16 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 16 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 64 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.15 (Relevance 1/10)
PCD = No. of Teeth x 0.150mm. 20 Degree Pressure Angle. Brass.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.25 (Relevance 1/10)
PCD = No. of Teeth x 0.250mm. 20 Degree Pressure Angle. Brass and carbon steel.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.4 (Relevance 1/10)
PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 (Relevance 1/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 - Hobby - Economy (Relevance 1/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle - POM Plastic
Plastic Only Inexpensive for hobby and toy use No locking mechanisms
|
Gears - Spur - Module 0.7 (Relevance 1/10)
PCD = No. of Teeth x 0.700mm. 20 Degree Pressure Angle. Acetal.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.75 (Relevance 1/10)
PCD = No. of Teeth x 0.750mm. 20 Degree Pressure Angle. Brass.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.8 (Relevance 1/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 1/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.25 (Relevance 1/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.5 (Relevance 1/10)
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2 (Relevance 1/10)
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2.5 (Relevance 1/10)
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 3 (Relevance 1/10)
PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Hinges | |
Hinges - Flexi-Hinge - Precision (Relevance 1/10)
Double and Single Ended - Limited Angle Rotary Applications.
Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature.
|
Indexing | |
Mechanisms - Geneva (Relevance 1/10)
Geneva device provide precision mechanical intermittent motion.
303 Stainless Steel. Driver may travel in either direction and is reversible. Precision product.
|
|
