Categories that include the terms: GEARMOTORS and DC and SIZE and 27 and LOW and COST
|
Gearmotors |  |
Gearmotors - DC - Size 20 Low Cost (Relevance 10/10)
20mm Gearhead Body Diameter. Low cost. 70 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 27 Low Cost (Relevance 10/10)
27mm Gearhead Body Diameter. Low cost. 36 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 37/350 Low Cost (Relevance 10/10)
37mm Gearhead Body Diameter. Low cost. 160 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Low Voltage (Relevance 7/10)
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel.
|
Gearmotors - DC - Size 12 (Relevance 7/10)
12mm Gearhead Body Diameter.
|
Electrical | |
Adaptors - Power - AC to DC - Multi Plug (Relevance 3/10)
SAA Approved Australian Adaptors for AC to DC. Supplied with assorted plugs.
|
Gearboxes | |
Educational Gearbox Kits (Relevance 3/10)
Basic gearbox kits for prototyping, testing and learning
|
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 3/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 3/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 3/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 3/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 3/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 3/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 3/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 3/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - Basic - Hobby Kits (Relevance 3/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gearmotors - Open Gear (Relevance 3/10)
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
|
Solarbotics Gearmotors (Relevance 3/10)
Hobby gearmotors for all types of applications
|
Ladder Chain and Sprockets | |
Chain - Ladder - 4.242mm Pitch - Size 21 (Relevance 3/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 4.699mm Pitch - Size 19 (Relevance 3/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 7.264mm Pitch - Size 18 (Relevance 3/10)
Steel - Brass - Stainless - High Tensile.
|
Sprockets - Ladder Chain - 4.242mm Pitch - Size 21 (Relevance 3/10)
With and without Hubs. Plastic and Steel.
|
Sprockets - Ladder Chain - 7.264mm Pitch - Size 18 (Relevance 3/10)
With and without Hubs. Plastic and Steel.
|
Motors - DC - MAX Series | |
Motors - DC - MAX 40 (Relevance 3/10)
Precious metal brush commutation system. See Gearheads - Ondrives - MAX Series for matching gearheads.
Operating Temperature Range: -30°C to +85°C (Max. rotor temperature +85°C), Mass: 187g. Low inductance - much longer brush life and low electrical noise. Low inertia - low mechanical time constant for fast acceleration and high speed stability. High efficiency - low current consumption, ideal for battery powered applications. Linear speed torque characteristics - simple accurate control ideal for servo applications.
|
Motors - Hobby - Robotic - Appliances | |
Motors - DC 6mm Diameter (Relevance 3/10)
Our smallest motors at an affordable price.
Various models 10000 to 30000 rpm Low starting voltage of <0.8V Rated Voltage 1.3V 100 hours / 100000 turns mechanical life Less than 43 dB Mechanical Noise Level
|
Motors - DC 12.3X24.4 mm (Relevance 3/10)
M-300C Series 0.5 to 6 VDC - 1820 to 2700 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx. 22 grams.
|
Motors - DC 16.6X32.0 mm (Relevance 3/10)
M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 18.9X18.0X9.5 mm (Relevance 3/10)
M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams.
|
Motors - DC 20.0X25.0 mm (Relevance 3/10)
1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts
|
Motors - DC 23.6X25.0 mm (Relevance 3/10)
1.5 to 4.5 VDC - 12,500 RPM unloaded at 4.5 volts
|
Motors - DC 25.0X21.0 mm (Relevance 3/10)
M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 25.0x20.1X15.1 mm (Relevance 3/10)
M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X23.8 mm (Relevance 3/10)
M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X24.2X18.3 mm (Relevance 3/10)
MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 27.6X51.0 mm (Relevance 3/10)
Compact, high torque and reliable 16,200 RPM unloaded at 6 volts
|
Motors - DC 30.5X24.2 mm (Relevance 3/10)
M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 30.5X24.2X18.3 mm (Relevance 3/10)
MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 36.0X71.0 mm (Relevance 3/10)
High power, high speed 11,800 RPM unloaded at 12 volts
|
Motors - DC 42.0X78.0 mm (Relevance 3/10)
High power, high speed 18,800 to 20,000 RPM unloaded 6 volts to 12 volts
|
Motors - DC 42.0X85.0 mm (Relevance 3/10)
High power, high speed 9,700 RPM unloaded at 12 volts
|
Stepper Motors - Hybrid | |
Motors - Stepper - Hybrid - Nema Size 11 (Relevance 3/10)
Mounting hole centres 23.10 mm (+/- 0.2 mm) - Body Width 28.00 mm.
Refer PDF Link at bottm of internet page for sizes and wiring information. Hybrid Stepper Motors include a permanent magnet in the rotor.
|
Adhesives and Sealants | |
Threadlockers (Relevance 1/10)
ZAP, Molytec, Loctite, Pacer. Pipe sealant, low to high strength threadlockers. Hydraulic threadlocker. Wick-In. Stops threads loosening from vibration.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Stainless Steel - 304 Grade (Relevance 1/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 1/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 1/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 1/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 1/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 1/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Housings - Bearing - Pillow Block - Miniature (Relevance 1/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Belts | |
Belts - Vee - 12.7 x 10.0 mm - SPA (Relevance 1/10)
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 1/10)
Stainless steel ball type cam followers.
|
Cam Followers - Roller Type - Stainless Steel (Relevance 1/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Urethane Covered (Relevance 1/10)
Urethane tyred cam followers for noise reduction, reduced wear and non marking
|
Clamping and Locking | |
Rings - Tolerance (Relevance 1/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Couplings | |
Couplings - Bellows - Set Screw - Aluminium (Relevance 1/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Electrical | |
Power Supplies (Relevance 1/10)
24 V DC.
Standard : 24V DC Output, 110V AC input. Available on special order : 12V DC Output, 220/230V AC input.
|
Fasteners | |
Pins - Clevis - Plain (Relevance 1/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 304 (Relevance 1/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 1/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Zinc Plated (Relevance 1/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Taper - Imperial - Miniature (Relevance 1/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Miniature sizes. Stainless and Mild Steel.
|
Pins - Taper - Imperial - Standard (Relevance 1/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Pins - Taper - Metric (Relevance 1/10)
Metric Sizes 1:50 Taper
Metric Sizes to DIN 1.
|
Roll Pins - Hobby (Relevance 1/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Screws - Large Shallow Head (Relevance 1/10)
UNC - UNF - METRIC - Various Materials.
|
Hobby Accessories | |
Glow Plugs (Relevance 1/10)
Real McCoy, OS glow plugs and Super Tiger
|
Glow Starter Kits (Relevance 1/10)
Starter pack. Fuel Bottel, 4 in 1 spanner, glow starter and charger
|
Glow Starters (Relevance 1/10)
|
Propellers - Plane - Electric - Slow Fly (Relevance 1/10)
|
Hobby Condensed Selection | |
Hobby Washers - Precision Shim (Relevance 1/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Insert Bearings and Housings | |
Housings - Bearing - Pillow Block - Cast Iron (Relevance 1/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Pillow Block - Plastic (Relevance 1/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 1/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 1/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Screws - Ball - Thomson Saginaw (Relevance 1/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Carriage Assembly (Relevance 1/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 1/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Magnets | |
Magnets - Bar (Relevance 1/10)
Great hobby and educational magnets for learning about magnetic attraction
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Magnets - Ceramic Blocks (Relevance 1/10)
Low cost, light weight, high energy material
Non conductive hard brittle material Performs best at temperatures below 249 Deg C Can be cut with a diamond wheel Difficult to grind and can't be machined or drilled by normal methods Tolerance 0.13mm on all dimensions
|
Magnets - Ferrite (Relevance 1/10)
Small ferrite magnets with good pulling strength.
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Materials | |
Rod - Round - Acetal (Relevance 1/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 1/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Nylon (Relevance 1/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - PTFE (Relevance 1/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Polyester PETP (Relevance 1/10)
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 1/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Model Kit Accessories | |
Model Kit Masking Tape (Relevance 1/10)
Various sizes
|
Mounts and Vibration Control | |
Dampeners - Double Studded - Silicone (Relevance 1/10)
Damps low frequency vibrations.
Use for compression only.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 1/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Plastic - Hobby (Relevance 1/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 1/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 1/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex (Relevance 1/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 1/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 1/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 1/10)
Includes Miniature Sizes.
|
Chain - Roller - Plastic - Simplex (Relevance 1/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 1/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 1/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Shim | |
Shim - Tin (Relevance 1/10)
Shim sheet. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Aluminium (Relevance 1/10)
Includes listing on 6061-T6 Aluminium Sheet. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Brass (Relevance 1/10)
Brass shim sheet. Very thin foil to thick sizes. Also one assortment pack listed.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes strips, sheets and rolls.
|
Shim and Foil - Copper (Relevance 1/10)
Shim sheet. Very thin foil to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Stainless Steel (Relevance 1/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Steel (Relevance 1/10)
Shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Sleeving | |
Sleeving - Mesh (Relevance 1/10)
Low cost protection for exterior threaded and cylindrical parts
Elastic snug tight fit on straight, tapered or contoured parts Made from polyethylene Thickness of web approx 1.8mm
|
Splined Shafts and Bushes | |
Splined Bushes - Unflanged (Relevance 1/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Splined Shafts (Relevance 1/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Tools | |
Tools - Dies (Relevance 1/10)
Tungsten Chrome Alloy - Carbon Steel. Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
|
Tools - Drill Bits (Relevance 1/10)
Micro miniature drill bits starting from 0.32mm up to larger standard sizes. Sutton - PN - Bordo.
Lengths shown are based on standard stock but may vary.
|
Tools - Drill Bits - Stepped (Relevance 1/10)
Stepped drill bits for drilling through materials in with a range of sizes.
|
Tools - Taps (Relevance 1/10)
High Speed Steel Short Machine and Carbon Steel Straight Flute Taps. starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
High Speed Steel (HSS) Short Machine and Hand Taps. Carbon Steel (CS) Hand taps.
|
|
