Gears - Hobby And Engineering Parts

Categories that include the term: GEARS Clamping and Locking Clamps - Gear - Screw Type (Relevance 10/10) Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears. Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table. Clamps - Gear - Split (Relevance 10/10) Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears. Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table. Clamps - Gear - Two Piece - Commercial Balanced (Relevance 10/10) Commercial - Stainless - Aluminium - Carbon Steel - For our clamp type gears. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only. Clamps - Gear - Two Piece - Precision Balanced (Relevance 10/10) Precision - Stainless - Aluminium - Carbon Steel - For our clamp type gears. Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. These clamps are designed to clamp the OD of the hub on our clamp type gears. The shaft size listed is for reference only. Hubs - Gear and Dial - Double (Relevance 10/10) Set screw mounting. Hubs - Gear and Dial - Removable Type (Relevance 10/10) Diameters MD and d concentric within 0.0076 mm T.I.R (Total Indicator Runout). Hubs - Gear and Dial - Single (Relevance 10/10) Fairloc Hubs require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Couplings Couplings - Crowned Tooth Gear Type. 19.55 to 88 Nm. 8500 to 14000 rpm. (Relevance 10/10) Steel hubs with Moulded Nylon Sleeve. +/- 1.02 mm Axial Displacement. 0.41mm Parallel offset per hub. 1 Degree Angular Displacement. Free axial movement. High torque / low inertia. Gearheads Gearheads - Inline - Spur Gear - Size 23 (Relevance 10/10) Use with NEMA Size 23 Motors. Steel Housing - Aluminium Flanges - Stainless Steel Heat Treated Gears - Ball Bearings. Double Stage / Max 5000 RPM Input Speed. Continuous Torque 6.65 N.m (50 lb.in) / Peak Torque 13.3 N.m (100 lb.in). Min Efficiency 90% / Max. Backlash 20 min. Gearheads - Inline - Spur Gear - Size 34 (Relevance 10/10) Use with NEMA Size 34 Motors. Steel Housing - Aluminium Flanges - Stainless Steel Heat Treated Gears - Ball Bearings. Double Stage / Max 5000 RPM Input Speed. Continuous Torque 28.2 N.m (250 lb.in) / Peak Torque 56.5 N.m (500 lb.in). Min Efficiency 90% / Max. Backlash 20 min. Gearheads - Inline - Spur Gear - Size 42 (Relevance 10/10) Use with NEMA Size 42 Motors. Steel Housing - Aluminium Flanges - Stainless Steel Heat Treated Gears - Ball Bearings. Double Stage / Max 5000 RPM Input Speed. Continuous Torque 56 N.m (500 lb.in) / Peak Torque 113 N.m (1000 lb.in). Min Efficiency 90% / Max. Backlash 20 min. Gearheads - Inline - Spur Gear - Size 56 (Relevance 10/10) Use with NEMA Size 56 Motors. Steel Housing - Aluminium Flanges - Stainless Steel Heat Treated Gears - Ball Bearings. Double Stage / Max 5000 RPM Input Speed. Continuous Torque 135 N.m (1200 lb.in) / Peak Torque 270 N.m (2400 lb.in). Min Efficiency 90% / Max. Backlash 20 min. Gearmotors Gearmotors - Open Gear (Relevance 10/10) Perfect for applications where inspection of the gears is important, educational purposes or for visual effects. Gears and Gearing Differentials - Precision (Relevance 10/10) Miniature precision stainless steel diffs. Gauges - Joining - Rack (Relevance 10/10) Gauges to determine correct alignment of ground racks. 20 Degree Pressure Angle. Gears - Bevel - 24 Pitch (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - 32 Pitch (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - 48 Pitch (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Module 0.5 (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Module 0.8 (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Module 1 (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Module 1.5 (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Module 2 (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Module 2.5 (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Module 3 (Relevance 10/10) For 90 degree angle power transfer. 20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios. Gears - Bevel - Spiral - Module 2 (Relevance 10/10) For 90 degree angle power transfer. See Gears - Mitre for 1:1 ratios. ISO Class 6. 35 Degree Spiral Angle / 20 Degree Pressure Angle. AISI 1045 Steel, Tooth surfaces induction hardened to HRC48.53. Black oxide finish except bore and tooth surfaces. Gears - Bevel - Spiral - Module 2.5 (Relevance 10/10) For 90 degree angle power transfer. See Gears - Mitre for 1:1 ratios. ISO Class 6. 35 Degree Spiral Angle / 20 Degree Pressure Angle. AISI 1045 Steel, Tooth surfaces induction hardened to HRC48.53. Black oxide finish except bore and tooth surfaces. Gears - Bevel - Spiral - Module 3 (Relevance 10/10) For 90 degree angle power transfer. See Gears - Mitre for 1:1 ratios. ISO Class 6. 35 Degree Spiral Angle / 20 Degree Pressure Angle. AISI 1045 Steel, Tooth surfaces induction hardened to HRC48.53. Black oxide finish except bore and tooth surfaces. Gears - Bevel - Spiral - Module 4 (Relevance 10/10) For 90 degree angle power transfer. See Gears - Mitre for 1:1 ratios. ISO Class 6. 35 Degree Spiral Angle / 20 Degree Pressure Angle. AISI 1045 Steel, Tooth surfaces induction hardened to HRC48.53. Black oxide finish except bore and tooth surfaces. Gears - Blanks (Relevance 10/10) Blanks for cutting gears and pulleys and friction drives. Gears - Cluster - 48 Pitch (Relevance 10/10) Have a mounting area for a second gear - see diagram. All have a 20 deg. Pressure Angle. Mounting diameter 9.525 (+0.008 / -0.000) mm (3/8 in.). Mounting area width 3.175 mm (1/8 in.). See diagram for mounting position of second gear. Combine with a gear from the listings under Gears - Spur …. - Hub Mounting. Gears - Cluster - 64 Pitch (Relevance 10/10) Have a mounting area for a second gear - see diagram. All have a 20 deg. Pressure Angle. Mounting diameter 9.525 (+0.008 / -0.000) mm (3/8 in.). Mounting area width 3.175 mm (1/8 in.). See diagram for mounting position of second gear. Combine with a gear from the listings under Gears - Spur …. - Hub Mounting. Gears - Cluster - 72 Pitch (Relevance 10/10) Have a mounting area for a second gear - see diagram. All have a 20 deg. Pressure Angle. Mounting diameter 9.525 (+0.008 / -0.000) mm (3/8 in.). Mounting area width 3.175 mm (1/8 in.). See diagram for mounting position of second gear. Combine with a gear from the listings under Gears - Spur …. - Hub Mounting. Gears - Cluster - 80 Pitch (Relevance 10/10) Have a mounting area for a second gear - see diagram. All have a 20 deg. Pressure Angle. Mounting diameter 9.525 (+0.008 / -0.000) mm (3/8 in.). Mounting area width 3.175 mm (1/8 in.). See diagram for mounting position of second gear. Combine with a gear from the listings under Gears - Spur …. - Hub Mounting. Gears - Helical - 48 Normal Pitch (Relevance 10/10) Gears - Helical - Module 1 (Relevance 10/10) Gears - Helical - Module 1.5 (Relevance 10/10) Gears - Helical - Module 2 (Relevance 10/10) Gears - Internal - 24 Pitch (Relevance 10/10) Various materials including 2024-T4 Aluminum, 303 stainless steel and brass. Gears - Internal - 32 Pitch (Relevance 10/10) Various materials including 2024-T4 Aluminum, 303 stainless steel and brass. Gears - Internal - 48 Pitch (Relevance 10/10) 2024-T4 Aluminum and 303 stainless steel. Gears - Internal - 64 Pitch (Relevance 10/10) 2024-T4 Aluminum and 303 stainless steel. Gears - Internal - 72 Pitch (Relevance 10/10) 2024-T4 Aluminum and 303 stainless steel. Gears - Internal - 96 Pitch (Relevance 10/10) 2024-T4 Aluminum and 303 stainless steel. Gears - Internal - Module 0.5 (Relevance 10/10) 2024-T4 Aluminum and 303 stainless steel. Gears - Internal - Module 0.8 (Relevance 10/10) 2024-T4 Aluminum and 303 stainless steel. Gears - Internal - Module 1 (Relevance 10/10) 2024-T4 Aluminum and 303 stainless steel. Gears - Mitre - 16 Pitch (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Nylon. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - 20 Pitch (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Unhardened Steel. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - 24 Pitch (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - 32 Pitch (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - 48 Pitch (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass, carbon steel and acetal. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 0.5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Brass and acetal. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 0.6 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 0.8 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Acetal and brass. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 1 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 1.5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 2 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 2.5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 2.75 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Steel. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 3 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Module 3.5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - Zinc die cast and steel. Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 1 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 1.25 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 1.5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 2 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 2.25 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 2.5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 3 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 3.5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 4 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Mitre - Spiral - Module 5 (Relevance 10/10) 1:1 Ratio. 20 Degree Pressure Angle - 35 Degree Spiral tooth - Steel. A set of spiral mitre gears must be identical in module and number of teeth but opposite in spiral direction. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios. Gears - Pinion Wire - 24 Pitch (Relevance 10/10) Brass and carbon steel. Metallic. Gears - Pinion Wire - 32 Pitch (Relevance 10/10) Brass and carbon steel. Metallic. Gears - Pinion Wire - 44 Pitch (Relevance 10/10) Brass and carbon steel. Metallic. Gears - Pinion Wire - 48 Pitch (Relevance 10/10) Brass and carbon steel. Metallic. Gears - Pinion Wire - 64 Pitch (Relevance 10/10) Brass and carbon steel. Metallic. Gears - Pinion Wire - Module 0.4 (Relevance 10/10) Brass. Metallic. Gears - Pinion Wire - Module 0.5 (Relevance 10/10) Brass. Metallic. Gears - Pinion Wire - Module 0.8 (Relevance 10/10) Brass. Metallic. Gears - Racks - 1/10 Pitch (Relevance 10/10) 20 Degree Pressure Angle. 416 Stainless Steel. Metallic. Gears - Racks - 1/20 Pitch (Relevance 10/10) 20 Degree Pressure Angle. 416 Stainless Steel. Metallic. Gears - Racks - 16 Pitch - 14.5 Degree (Relevance 10/10) 14.5 Degree Pressure Angle. Nylon. Plastic. Gears - Racks - 24 Pitch - 14.5 Degree (Relevance 10/10) 14.5 Degree Pressure Angle. Brass, carbon steel and nylon. Plastic and metallic. Gears - Racks - 24 Pitch - 20 Degree (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - 32 Pitch - 14.5 Degree (Relevance 10/10) 14.5 Degree Pressure Angle. Brass, carbon steel and nylon. Plastic and metallic. Gears - Racks - 32 Pitch - 20 Degree (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - 48 Pitch - 14.5 Degree (Relevance 10/10) 14.5 Degree Pressure Angle. Brass, carbon steel and nylon. Plastic and metallic. Gears - Racks - 48 Pitch - 20 Degree (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - 64 Pitch (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - 72 Pitch (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - 80 Pitch (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - 96 Pitch (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - 120 Pitch (Relevance 10/10) 20 Degree Pressure Angle. 416 stainless steel and aluminium. Metallic. Gears - Racks - Circular Pitch 2 (Relevance 10/10) 20 Degree Pressure Angle. Hardened steel. Gears - Racks - Circular Pitch 5 (Relevance 10/10) 20 Degree Pressure Angle. Hardened steel. Gears - Racks - Flexible (Relevance 10/10) Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm. 20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order. Gears - Racks - Flexible - Clamps (Relevance 10/10) For clamping acetal flexirack. Gears - Racks - Flexible - Guide Rails (Relevance 10/10) For mounting flexirack. Flexible nylon or rigid aluminium guide rails. Longer lengths in Nylon available on special order. Gears - Racks - Module 0.3 (Relevance 10/10) 20 Degree Pressure Angle. Brass. Metallic. Gears - Racks - Module 0.4 (Relevance 10/10) 20 Degree Pressure Angle. Brass, carbon steel and nylon. Plastic and metallic. Gears - Racks - Module 0.5 (Relevance 10/10) 20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon. Plastic and metallic. Gears - Racks - Module 0.75 (Relevance 10/10) 20 Degree Pressure Angle. Brass and stainless steel. Metallic. Gears - Racks - Module 0.8 (Relevance 10/10) 20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon. Plastic and metallic. Gears - Racks - Module 1 (Relevance 10/10) 20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon. Plastic and metallic. Gears - Racks - Module 1.25 (Relevance 10/10) 20 Degree Pressure Angle. Acetal. Plastic. Gears - Racks - Module 1.5 (Relevance 10/10) 20 Degree Pressure Angle. Carbon steel, stainless steel, acetal and nylon. Plastic and metallic. Gears - Racks - Module 2 (Relevance 10/10) 20 Degree Pressure Angle. Carbon steel, acetal and nylon. Plastic and metallic. Gears - Racks - Module 2.5 (Relevance 10/10) 20 Degree Pressure Angle. Carbon steel, acetal and nylon. Plastic and metallic. Gears - Racks - Module 3 (Relevance 10/10) 20 Degree Pressure Angle. Carbon steel, acetal and nylon. Plastic and metallic. Gears - Spur - 16 Pitch - 14.5 Degree (Relevance 10/10) PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon. Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 16 Pitch - 20 Degree (Relevance 10/10) PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal. Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 10/10) PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 24 Pitch - 20 Degree (Relevance 10/10) PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 24 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 24 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 10/10) PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 32 Pitch - 20 Degree (Relevance 10/10) PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 32 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 32 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 10/10) PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 48 Pitch - 20 Degree (Relevance 10/10) PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 48 Pitch - Differential End (Relevance 10/10) To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel. Metallic. Gears - Spur - 48 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 48 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - 64 Pitch (Relevance 10/10) PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 64 Pitch - Differential End (Relevance 10/10) To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel. Metallic. Gears - Spur - 64 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 64 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - 72 Pitch (Relevance 10/10) PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal. Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 72 Pitch - Differential End (Relevance 10/10) To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel. Metallic. Gears - Spur - 72 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 72 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - 80 Pitch (Relevance 10/10) PCD = No. of Teeth x 0.318mm (1/80 in.). 20 Degree Pressure Angle. 2024 aluminium and 303 stainless steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 80 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 80 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - 96 Pitch (Relevance 10/10) PCD = No. of Teeth x 0.265mm (1/96 in.). 20 Degree Pressure Angle. 2024 aluminium and 303 stainless steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 96 Pitch - Differential End (Relevance 10/10) To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel. Metallic. Gears - Spur - 96 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 96 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - 120 Pitch (Relevance 10/10) PCD = No. of Teeth x 0.212mm (1/120 in.). 20 Degree Pressure Angle. 2024 aluminium and 303 stainless steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - 120 Pitch - Hub Mounting (Relevance 10/10) Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal. Plastic and metallic. Gears - Spur - 120 Pitch - Stem (Relevance 10/10) 303 stainless steel. Metallic. Gears - Spur - Circular Pitch 2 (Relevance 10/10) PCD = No. of Teeth x 0.636mm (2.000 / Pi.). Various styles and materials. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Circular Pitch 5 (Relevance 10/10) PCD = No. of Teeth x 1.591mm (5.000 / Pi.). Various styles and materials. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.15 (Relevance 10/10) PCD = No. of Teeth x 0.150mm. 20 Degree Pressure Angle. Brass. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.2 (Relevance 10/10) PCD = No. of Teeth x 0.200mm. 20 Degree Pressure Angle. Brass. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.25 (Relevance 10/10) PCD = No. of Teeth x 0.250mm. 20 Degree Pressure Angle. Brass and carbon steel. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.3 (Relevance 10/10) PCD = No. of Teeth x 0.300mm. 20 Degree Pressure Angle. Brass. Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.4 (Relevance 10/10) PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Gears - Spur - Module 0.5 (Relevance 10/10) PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel. Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance. Too many choices? You have selected to see ALL categories containing the term GEARS. Click here to see ONLY THE MOST POPULAR categories containing the term GEARS.

Cart total A$ 0.00 You may need to refresh the page if your selected currency doesn't change. Currency Options Default (USD) British Pound Canadian Dollar Euro Hong Kong Dollar Japanese Yen New Zealand Dollar Singapore Dollar US Dollar Swiss Francs You may need to refresh the page if your selected currency doesn't change. Item Popularity Show only popular categories Pictures Hide pictures Show all categories starting with A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9 Major Categories Adaptors Adhesives Aircraft Aircraft Parts Ansmann Parts Axial Parts Balls Bar Batteries Bearings Belts Bikes (Models) Boats Books (Hobby) Bushes Carbon Fibre Cars - Buggies - Truggies Car Parts Castors Ceramic Chain Circlips Clamps Collars Colt Parts Couplings Cranks Dental Bearings and Parts Dowel Pins Dragon Hobby Parts Drylin Dual Vee Dubro Parts DVD's (Hobby) Educational Products E-Flite Parts E-Sky Parts Engines Engine Parts Fishing Reel Bearings Fuel Games Gas Springs Gearboxes Gearmotors Gears Great Vigor Parts Handles Hangar 9 Parts Helicopters Helicopter Bearings Helicopter Parts Housings Hubs Joints Keysteel Knobs Kyosho Parts Lazy Susans Leadscrews Levers Linear Bearings Losi Parts Lubricants Materials Model Kits and Accessories Motors Mounts Mousetrap Vehicles MVVS Engine Parts Multiplex Parts Nuts O-Rings Oil Seals OS Engine Parts Paint Parkzone Parts Parts Boxes Pins Planes Plane Parts Pulleys Ratchets Reducers Rod Rod Ends Rollers Saito Parts Screws Shafting Sheet Shim Slides Solarbotics Solar Cells Spacers Sportwerks Parts Springs Sprockets Steam Boats and Engines Super Tigre Parts Surplus Specials Suspension Units Tamiya Parts Threaded Rod Tools Tube Universal Joints Venom Parts Vibration Mounts Washers Wheels Worms Zenoah Engine Parts SEARCH Product Description (Category) Information Search Part Number (ours) Part Number (other) Guided Search CATALOGUES Catalogues Index Catalogue A-Z Online Catalogues A-Z PDF Discount Registration Online Catalogue Quick Guides Surplus Stock   Adhesives Aircraft Aircraft Parts Ansmann Parts Axial Parts Bar Batteries Bearings Bikes (Models) Boats Books (Hobby) Carbon Fibre Cars - Buggies - Truggies Car Parts Ceramic Colt Parts Couplings Dental Bearings and Parts Dragon Hobby Parts Dubro Parts DVD's (Hobby) E-Flite Parts E-Sky Parts Engines Engine Parts Fishing Reel Bearings Fuel Games Gears Great Vigor Parts Hangar 9 Parts Helicopters Helicopter Bearings Helicopter Parts Hobbyzone Parts Kyosho Parts Losi Parts Materials Model Kits and Accessories Motors Mousetrap Vehicles Multiplex Parts MVVS Engine Parts OS Engine Parts Paint Parkzone Parts Parts Boxes PDF A-Z All Categories Planes Plane Parts Products Not Listed Here Saito Parts Screws Solar Cells Solarbotics Sportwerks Parts Steam Boats and Engines Super Tigre Parts Surplus Stock Specials Tamiya Parts Tools Tube Venom Parts Zenoah Engine Parts   Products Not Listed Above Quick Guides HOW TO & ABOUT US Charity Contact Us Frequently Asked Questions Freight Rates Home How To Order Online Mailorder Newsletter Subscription Order Specially Quoted Parts Payment Options Terms and Conditions of Sale PRODUCT INFORMATION Dental Bearings Hobby Information Information Sheets New Products Surplus Specials Lists Technical Information RECOMMENDED LINKS ACMA Radio Frequencies ACMA Frequencies Class License Couplings Information eParcel Tracking Express International Tracking Gearboxes Information Jokes and Trivia Materials Information Miniature Bearings Australia Ondrives UK Rino UK Shafting Information Shafting Information Stainless Selection Tingalpa Model Aero Club TNT Freight Tracking Unfair Contracts Wikipedia Windows to The Universe World Time

• Search for information pages instead of products
• Mail Order Form
• Order non-standard parts quoted by e-mail
• Freight Rates
• Terms of Sale

All care has been taken in the compilation of this page, however errors may occur. Please do not use the information contained herein for critical applications without first re-checking the information with an independent source. No responsibility will be accepted by Hobby & Engineering Supplies Pty Ltd or the Directors of said company for any loss of any kind that may be incurred in any way whatsoever from use of the information provided in these pages.

***** Trademarks *****

Delrin^TM is a registered trademark of duPont Corporation
Teflon^TM is a registered trademark of duPont Corporation

HES Terms and Conditions of Sale

HES Privacy Policy