Categories that include the term: GEARS
|
Clamping and Locking |  |
Clamps - Gear - Screw Type (Relevance 10/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 10/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Gearboxes | |
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 10/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 10/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 10/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - DC - Size 12 (Relevance 10/10)
12mm Gearhead Body Diameter.
|
Solarbotics Gearmotors (Relevance 10/10)
Hobby gearmotors for all types of applications
|
Gears and Gearing | |
Gears - Bevel - 32 Pitch (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 48 Pitch (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.5 (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.8 (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1 (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1.5 (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2 (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2.5 (Relevance 10/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Internal - Module 0.5 (Relevance 10/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 0.8 (Relevance 10/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 1 (Relevance 10/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Mitre - 16 Pitch (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 24 Pitch (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 32 Pitch (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 48 Pitch (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass, carbon steel and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.5 (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Brass and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.6 (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1 (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3.5 (Relevance 10/10)
1:1 Ratio. 20 Degree Pressure Angle - Zinc die cast and steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 14.5 Degree (Relevance 10/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 24 Pitch - 20 Degree (Relevance 10/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 32 Pitch - 14.5 Degree (Relevance 10/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 48 Pitch - 14.5 Degree (Relevance 10/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 64 Pitch (Relevance 10/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 72 Pitch (Relevance 10/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 96 Pitch (Relevance 10/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 120 Pitch (Relevance 10/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - Flexible (Relevance 10/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Gears - Racks - Flexible - Guide Rails (Relevance 10/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Gears - Racks - Module 0.4 (Relevance 10/10)
20 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.5 (Relevance 10/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 0.75 (Relevance 10/10)
20 Degree Pressure Angle. Brass and stainless steel.
Metallic.
|
Gears - Racks - Module 0.8 (Relevance 10/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1 (Relevance 10/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 1.25 (Relevance 10/10)
20 Degree Pressure Angle. Acetal.
Plastic.
|
Gears - Racks - Module 1.5 (Relevance 10/10)
20 Degree Pressure Angle. Carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 2 (Relevance 10/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Racks - Module 3 (Relevance 10/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - 16 Pitch - 14.5 Degree (Relevance 10/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 16 Pitch - 20 Degree (Relevance 10/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 10/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 10/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - Stem (Relevance 10/10)
303 stainless steel.
Metallic.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 10/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 10/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 10/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 10/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 10/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 64 Pitch (Relevance 10/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 10/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch - Differential End (Relevance 10/10)
To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel.
Metallic.
|
Gears - Spur - 72 Pitch - Stem (Relevance 10/10)
303 stainless steel.
Metallic.
|
Gears - Spur - Module 0.25 (Relevance 10/10)
PCD = No. of Teeth x 0.250mm. 20 Degree Pressure Angle. Brass and carbon steel.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.4 (Relevance 10/10)
PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 (Relevance 10/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.7 (Relevance 10/10)
PCD = No. of Teeth x 0.700mm. 20 Degree Pressure Angle. Acetal.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.8 (Relevance 10/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 10/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.25 (Relevance 10/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.5 (Relevance 10/10)
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2 (Relevance 10/10)
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2.5 (Relevance 10/10)
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 3 (Relevance 10/10)
PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Stock - 20 Pitch (Relevance 10/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears - Spur - Stock - 24 Pitch (Relevance 10/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears - Spur - Stock - Module 1 (Relevance 10/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears and Gearing - Matched Sets | |
Gears - Mitre - 48 Pitch - Precision Matched Sets (Relevance 10/10)
Sold as sets - 1:1 Ratio. Stainless steel and aluminium.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90 degree angle.
|
Hobby Condensed Selection | |
Hobby Gears - Spur - 48DP (Relevance 10/10)
A small selection of popular 48DP Plastic/ Metal Pinion and Spur gears
See main listings under Gears for sizes not listed here To work out the pitch diameter of a 48DP spur gear, divide multiply the no of teeth by 0.52917.
|
Hobby Gears - Worm and Wheel 40 : 1 Plastic (Relevance 10/10)
Popular Hobby Set
1 start 40 tooth gear.
|
Worms and Worm Gears | |
Worm Gears - 24 Pitch (Series 1) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 2) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 2) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 1) - Metallic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 64 Pitch (Series 1) - Metallic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 10/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 1) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 2) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 1) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 2) - Plastic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 48 Pitch (Series 1) - Metallic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 64 Pitch (Series 1) - Metallic (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 10/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 10/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Fishing Reel Parts | |
440 - 454 - 541 - 545 Pro Gear Parts (Relevance 8/10)
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
|
Adhesives and Sealants | |
Retaining Compounds (Relevance 3/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Clamping and Locking | |
Rings - Tolerance (Relevance 3/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Kits | |
Assortment Kits - Various (Relevance 3/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Materials | |
Rod - Round - Acetal (Relevance 3/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Tools | |
Tools - General (Relevance 3/10)
Needle Files, Pin Vises, Gear Gauge, Wire and Tube Benders, Tube Cutters, Miniature tap, Turnbuckle Wrench, Shock Matching Tool and die set
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more
|
Tools - Pullers - Small (Relevance 3/10)
Small pullers for miniature bearings, gears, pulleys, sprockets and other pressed on parts.
|
Belt and Sprockets - Posi-Drive | |
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core (Relevance 1/10)
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Belts | |
Belts - Rounthane (Relevance 1/10)
Joinable belting.
Join with Rounthane Connectors. Material : Non Slip Polyurethane. Use with grooved idler pulleys or 6.35mm Top Width V Pulleys. Purchased per 305mm (1 foot). Orders for more than 1 foot will be supplied as a continuous length.
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Hobby Accessories | |
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Pulleys | |
Pulleys - Flat Belt (Relevance 1/10)
Polycarbonate pulleys for flat belts 6mm or 6.35mm wide.
Aluminium Knurled Inserts. Gold Iridite Brass Knurled Inserts. Set Screw Locking.
|
Pulleys - Timing - 2.000mm Pitch - GT - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 3mm Wide Belts (Relevance 1/10)
Timing Pulleys to suit GT 2mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 6mm Wide Belts (Relevance 1/10)
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide.
Various materials as shown.
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 9mm Wide Belts (Relevance 1/10)
Timing Pulleys to suit 2mm Pitch GT Timing Belts 9mm Wide.
Aluminium Alloy
|
Pulleys - Timing - 2.032mm Pitch - MXL (Relevance 1/10)
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.032mm Pitch - MXL - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 2.073mm Pitch - 40DP (Relevance 1/10)
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.500mm Pitch - T2.5 (Relevance 1/10)
Timing Pulleys to suit T Series 2.500mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.500mm Pitch - T2.5 - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 3.000mm Pitch - GT - To Suit 9mm Wide Belts (Relevance 1/10)
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 9mm Wide.
Various materials as shown.
|
Pulleys - Timing - 3.000mm Pitch - HTD (Relevance 1/10)
Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 3.000mm Pitch - HTD - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 5.000mm Pitch - GT (Relevance 1/10)
|
Pulleys - Timing - 5.000mm Pitch - HTD (Relevance 1/10)
Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 5.000mm Pitch - HTD - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 5.000mm Pitch - T5 (Relevance 1/10)
Timing Pulleys to suit T Series 5.000mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 5.080mm Pitch - XL (Relevance 1/10)
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 5.080mm Pitch - XL - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 9.525mm Pitch - L (Relevance 1/10)
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 10.000mm Pitch - T10 - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - U Groove - Idler (Relevance 1/10)
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
|
Pulleys - U Groove - Plastic (Relevance 1/10)
Acetal Body with Brass Insert.
|
Pulleys - U Groove - Steel (Relevance 1/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Pulleys - Vee - M / 3L - Single Row - Through Bore (Relevance 1/10)
|
Pulleys - Vee - Y / 2L - Single Row - Through Bore (Relevance 1/10)
|
|
