Categories that include the terms: HEXAGONAL and BAR and CARBON and STEEL
|
Materials |  |
Hexagonal Bar - Carbon Steel (Relevance 10/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Square Bar - Carbon Steel (Relevance 10/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Fasteners | |
Nuts - Hexagonal - Half - Stainless Steel (Relevance 7/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 7/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 7/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 7/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 7/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 7/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 7/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Linear Drive Systems - Leadscrew | |
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 7/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Materials | |
Hexagonal Bar - 303 Stainless (Relevance 7/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
|
Rod - Round - Carbon Fibre (Relevance 7/10)
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Rod - Round - Stainless Steel (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 7/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - PTFE Lined (Relevance 7/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Washers | |
Washers - Disc Spring - Carbon Steel (Relevance 7/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 7/10)
Flat Carbon Spring Steel Washers.
|
Balls | |
Balls - Bored - Steel (Relevance 4/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Balls - Chrome Steel (Relevance 4/10)
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
|
Balls - Stainless Steel - 304 Grade (Relevance 4/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 4/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 4/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 4/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 4/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Fasteners | |
Joints - Clevis - Steel (Relevance 4/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Nuts - Cap - Stainless Steel (Relevance 4/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 4/10)
Stainless Steel.
|
Nuts - Dome - Steel (Relevance 4/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Aluminium (Relevance 4/10)
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Binx (Relevance 4/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Hexagonal - Brass (Relevance 4/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Hexagonal - Nylon (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Titanium - CP Grade 1 (Relevance 4/10)
METRIC. CP Grade 1.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Nuts - Wing - Stainless Steel (Relevance 4/10)
304 and 316 Stainless Wing Nuts
|
Nuts - Wing - Steel (Relevance 4/10)
Zinc Plated Wing Nuts
|
Pins - Clevis - Stainless Steel 304 (Relevance 4/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 4/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Stainless Steel (Relevance 4/10)
Split pins.
|
Pins - Dowel - Standard - Hardened Steel (Relevance 4/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 4/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 4/10)
304 and 420 grades DIN1481.
|
Screws - Hex Head - Steel (Relevance 4/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Machine - Stainless Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 4/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Alloy Steel (Relevance 4/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 4/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Alloy Steel (Relevance 4/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Threaded Rod - Allthread - Brass (Relevance 4/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 4/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Aluminium (Relevance 4/10)
UNC and UNF light weight aluminium.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 4/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Insert Bearings and Housings | |
Bearings - For Pressed Metal Housings (Relevance 4/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Keys and Keysteel | |
Keys - Gib Head - Steel (Relevance 4/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Linear Motion Bearings | |
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 4/10)
For running on shafts fixed at the ends.
|
Magnets | |
Magnets - Alcomax - Rectangular Bar (Relevance 4/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 4/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Rod - Sintered (Relevance 4/10)
|
Magnets - Bar (Relevance 4/10)
Great hobby and educational magnets for learning about magnetic attraction
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Materials | |
Bar - H Section - Brass (Relevance 4/10)
|
Bar - I Beam - Brass (Relevance 4/10)
|
Rectangular Bar - Brass (Relevance 4/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Rod - Half Round - Styrene (Relevance 4/10)
Styrene (ABS) Plastic
|
Rod - Round - Acetal (Relevance 4/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Aluminium (Relevance 4/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Brass (Relevance 4/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 4/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Glass Fibre (Relevance 4/10)
High impact light weight glass fibre for modelling.
Glass fibre rod is not smooth.
|
Rod - Round - Nylon (Relevance 4/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - PTFE (Relevance 4/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Polyester PETP (Relevance 4/10)
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Sintered Bronze (Relevance 4/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Rod - Round - Styrene (Relevance 4/10)
Styrene (ABS) Plastic
|
Rod - Round - Urethane (Relevance 4/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Sheet - Carbon Fibre (Relevance 4/10)
3K Solid Sheet
|
Square Bar - 303 Stainless (Relevance 4/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Square Bar - Brass (Relevance 4/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
|
Strip - Carbon Fibre (Relevance 4/10)
High impact light weight carbon fibre for modelling.
|
Tube - Hexagonal - Brass (Relevance 4/10)
Hexagonal hollow tubing.
|
Tube - Rectangular - Carbon Fibre (Relevance 4/10)
High impact light weight carbon fibre hollow tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish
|
Tube - Round - Carbon Fibre (Relevance 4/10)
High impact light weight carbon fibre hollow tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Tube - Round - Stainless Steel (Relevance 4/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Square - Carbon Fibre - Round Hole (Relevance 4/10)
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Tube - Square - Carbon Fibre - Square Hole (Relevance 4/10)
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Wire - Steel - Spring - Music Wire (Relevance 4/10)
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
|
Plain Bearings | |
Bushes - Steel - PTFE Lined - Split (Relevance 4/10)
Similar style to Glacier™ bushes.
|
Bushings - Spherical - Steel (Relevance 4/10)
Steel
Compensates for axial loads and misalignment.
|
Pulleys | |
Pulleys - U Groove - Steel (Relevance 4/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Reels | |
Reels - Spring Powered - Base Mounted - Steel (Relevance 4/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 4/10)
301 S11/S22 Stainless Steel.
|
Snaprings - Internal - Stainless Steel (Relevance 4/10)
301 S11/S22 Stainless Steel.
|
Rod Ends | |
Rod Ends - Plastic (Relevance 4/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 4/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 4/10)
High tensile steel.
|
Chain - Roller - Metal - Simplex (Relevance 4/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 4/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 4/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 4/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 4/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 4/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 4/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 4/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 4/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 4/10)
|
Rollers - Steel (Relevance 4/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Shaft and Shafting | |
Rod - Drill (Relevance 4/10)
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight.
|
Shim | |
Shim and Foil - Stainless Steel (Relevance 4/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Steel (Relevance 4/10)
Shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Silver Steel | |
Shafting - Ground - Precision (Relevance 4/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 4/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Spacers - Hex - Threaded - Stainless Steel (Relevance 4/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Steel (Relevance 4/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Round - Through Bore - Stainless Steel (Relevance 4/10)
Shaft spacers - Stainless Steel
|
Spacers - Round - Through Bore - Steel (Relevance 4/10)
Shaft spacers - Steel
|
Universal Joints | |
Universal Joints - Steel (Relevance 4/10)
Steel - Cast Zinc - Stainless Steel.
|
Washers | |
Washers - Cup - Stainless Steel (Relevance 4/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Disc Spring - Stainless Steel (Relevance 4/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Mild Steel (Relevance 4/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Stainless Steel - Commercial (Relevance 4/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 4/10)
Precision Tolerances.
|
Washers - Lock - External Tooth - Spring Steel (Relevance 4/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 4/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 4/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 4/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Keys and Keysteel | |
Keys - Gib Head - Zinc Plated (Relevance 3/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Keys - Keysteel Lengths - Rectangular (Relevance 3/10)
Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.
|
Keys - Keysteel Lengths - Round (Relevance 3/10)
Manufactured slightly oversize to prevent machine backlash.
|
Keys - Keysteel Lengths - Square (Relevance 3/10)
Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.
|
Keys - Machine (Relevance 3/10)
|
Keys - Woodruff (Relevance 3/10)
Stainless steel and carbon steel
|
Paint | |
Paint - Polycarbonate Spray - Tamiya (Relevance 3/10)
Cans of polycarbonate spray paint developed especially for decorating transparent polycarbonate bodies used in R/C car modeling.
Each can contains 100ml of paint, which is the appropriate amount for finishing a model. Paint the body from the inside, keeping the can about 30cm from the surface. After curing, apply another coat. Small details should be brush painted beforehand using Tamiya bottle paints for polycarbonate. These paints are impervious to oil and fuels, so they can be safely used on gas-powered R/C bodies. Never use these paints on plastic models.
|
Adhesives and Sealants | |
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Bored - Plastic (Relevance 1/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Batteries | |
Batteries - Hobby - NiMH (Relevance 1/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 1/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Ball - Single Row - Radial - Flanged (Relevance 1/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
|
