Categories that include the terms: HOBBY and NUTS and STANDARD
|
Hobby Accessories |  |
Propellers - Plane - Electric - Standard (Relevance 9/10)
|
Batteries | |
Batteries - Hobby - Lipo (Relevance 5/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom, Hacker. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - NiMH (Relevance 5/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - Nicad (Relevance 5/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Batteries - Standard (Relevance 5/10)
The Venom standard non-rechargeable battery range includes AA, AAA, C, D and 9V non-rechargeable.
Bulk packs and single cards
|
Fasteners | |
Nuts - Blind (Relevance 5/10)
Blind nuts - Tee nuts.
|
Nuts - Cap - Stainless Steel (Relevance 5/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Hexagonal - Binx (Relevance 5/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Wing - Stainless Steel (Relevance 5/10)
304 and 316 Stainless Wing Nuts
|
Nuts - Wing - Steel (Relevance 5/10)
Zinc Plated Wing Nuts
|
Pins - Taper - Imperial - Standard (Relevance 5/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Socket Set Screws - Cup Point - Standard (Relevance 5/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Hobby Accessories | |
Accessories - Hobby - Body Clips (Relevance 5/10)
Large and small body clips. Fluoro or standard. Plastic coated or anodised. Range of colours. Bent and straight.
|
Accessories - Hobby - General (Relevance 5/10)
General hobby supplies
Velcro Strip - ESC Fans - Heat Shrink - Motor Cooling Stands - Spring Dyno Camera Eye - Tuning Mat - Frequency Keys
|
Hobby Condensed Selection | |
Hobby Gears - Worm and Wheel 40 : 1 Plastic (Relevance 5/10)
Popular Hobby Set
1 start 40 tooth gear.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 5/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nut Flanges for Acme Nuts (Relevance 5/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 5/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Remote Control Aircraft | |
Foam Plane Kits Electric - Hobby Zone (Relevance 5/10)
Foam Plane Kits Electric - Hobby Zone
This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands Include: Super Cub LP
|
Spacers | |
Spacers - Round - Hobby (Relevance 5/10)
Inexpensive nylon spacers for hobby applications
|
Stepper Motors | |
Motors - Stepper - Basic Hobby (Relevance 5/10)
Small light weight stepper motor for your hobby or light duty projects
|
Tools | |
Hobby Tools - General (Relevance 5/10)
Flywheel Rench, Allen Key Set, Socket Driver Se, 4-way cross wrench, pioin stocker, ball end pliers, side cutters, long nose pliers, flat nose pliers, pinion storage, hobby scissors and body reamer.
See main listings for sizes not shown here.
|
Wheels | |
Wheels - Hobby - General (Relevance 5/10)
Includes wheels for robots and general hobby applications
Also see tracks for Robotic applications
|
Batteries | |
Batteries - Hobby - Kick Start (Relevance 4/10)
Kick start battery for your glow plugs.
|
Batteries - Hobby - Lead Acid (Relevance 4/10)
All types of Lead Acid Battery
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 4/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Books and DVD | |
Books - Hobby - General (Relevance 4/10)
Tips and tricks, maintenance and how-to guides.
|
Books - Hobby - Mousetrap Vehicles (Relevance 4/10)
Tips and tricks and how-to guides for Mousetrap powered cars and boats
|
Books - Hobby - RC Car and Truck (Relevance 4/10)
Tips and tricks, maintenance and how-to guides.
|
Books - Hobby - RC Planes (Relevance 4/10)
Tips and tricks, maintenance and how-to guides.
|
Hobby DVD (Relevance 4/10)
Note! DVD's are formatted for Zone 4 Australasia.
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 4/10)
Stainless steel ball type cam followers.
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 4/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 4/10)
For conveying materials. From miniature to large.
|
Clamping and Locking | |
Collars - Shaft - Standard (Relevance 4/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Couplings | |
Couplings - Helical - Standard (Relevance 4/10)
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Fasteners | |
Nuts - Aerotight (Relevance 4/10)
Aerotight is a Registered Trademark and can only be applied to goods manufactured by the Premier Screw and Repetition Company Limited. Any company infringing the registered trade mark may be liable to legal proceedings. Aerotight nuts should not be used on damaged or interrupted threads. When assembled on the screw at least two threads should protrude through the Aerotight nut. Advantages: Will not work loose. No other locking device needed.
|
Nuts - Dome - Nylon (Relevance 4/10)
Natural Nylon.
|
Nuts - Dome - Stainless Steel (Relevance 4/10)
Stainless Steel.
|
Nuts - Dome - Steel (Relevance 4/10)
Mild Steel, chrome and zinc plated
|
Nuts - Flange - Serrated (Relevance 4/10)
Stainless Steel.
|
Nuts - Hexagonal - Aluminium (Relevance 4/10)
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Brass (Relevance 4/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 4/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 4/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 4/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 4/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 4/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Titanium - CP Grade 1 (Relevance 4/10)
METRIC. CP Grade 1.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Nuts - Quick Release (Relevance 4/10)
Carbon steel, black oxide finish. Button Thread® nuts allow quick fixturing on long thread lengths. Simply press the button and the threads are disengaged to allow easy movement up or down the screw. Release the button and the threads engage for normal turning.
|
Nuts - Thumb (Relevance 4/10)
|
Nuts - Well (Relevance 4/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Nuts - Wing - Nylon (Relevance 4/10)
|
Pins - Dowel - Standard - Hardened Steel (Relevance 4/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 4/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Roll Pins - Hobby (Relevance 4/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 4/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - Basic - Hobby Kits (Relevance 4/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gears and Gearing | |
Gears - Spur - Module 0.5 - Hobby - Economy (Relevance 4/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle - POM Plastic
Plastic Only Inexpensive for hobby and toy use No locking mechanisms
|
Hobby Accessories | |
Accessories - Servo Programmer - Digital HFP20 (Relevance 4/10)
Servo programmer-tester for Hitec digital servos
|
Crystals - Remote Control (Relevance 4/10)
|
Dubro Accessories Listed by Description (Relevance 4/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Glow Plugs (Relevance 4/10)
Real McCoy, OS glow plugs and Super Tiger
|
Glow Starter Kits (Relevance 4/10)
Starter pack. Fuel Bottel, 4 in 1 spanner, glow starter and charger
|
Glow Starters (Relevance 4/10)
|
Gyros - Hobby (Relevance 4/10)
Hitec and more
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Leads and Connectors - Hobby (Relevance 4/10)
Adaptor leads for batteries, battery chargers, servos and receivers including Tamiya, Deans and Losi plugs.
Includes Deans and T Connectors
|
Propeller Hubs (Relevance 4/10)
|
Propellers - Boat (Relevance 4/10)
|
Propellers - Plane - Electric - Folding (Relevance 4/10)
|
Propellers - Plane - Electric - Slow Fly (Relevance 4/10)
|
Propellers - Plane - Nitro - 2 Blade (Relevance 4/10)
|
Propellers - Plane - Nitro - 3 Blade (Relevance 4/10)
|
Propellers - Plane - Nitro - 4 Blade (Relevance 4/10)
|
Receivers and Accessories (Relevance 4/10)
Receivers for Radio Control Equipment - Spektrum and Futaba
|
Speed Controllers - Aircraft (Relevance 4/10)
|
Speed Controllers - Car and Buggy (Relevance 4/10)
|
Speed Controllers - Marine (Relevance 4/10)
|
Spinners - 2 Blade (Relevance 4/10)
Spinners for aircraft propellers
|
Spinners - 3 Blade (Relevance 4/10)
Spinners for aircraft propellers
|
Tape - Double Sided (Relevance 4/10)
Double Sided Foam Tape
|
Tape - Glass Fibre (Relevance 4/10)
Hinge tape and other uses
|
Wire - Silicone (Relevance 4/10)
Silicone Wire in various colours and gauges
|
Hobby Condensed Selection | |
Hobby Gears - Spur - 48DP (Relevance 4/10)
A small selection of popular 48DP Plastic/ Metal Pinion and Spur gears
See main listings under Gears for sizes not listed here To work out the pitch diameter of a 48DP spur gear, divide multiply the no of teeth by 0.52917.
|
Hobby Gears - Spur - Module 0.4 (Relevance 4/10)
A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.
|
Hobby Gears - Spur - Module 0.5 (Relevance 4/10)
A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.
|
Hobby Washers - Precision Shim (Relevance 4/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - Economy - Rolled - Nut Only (Relevance 4/10)
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 4/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Materials | |
Rod - Round - Bronze - LG2 (Standard) (Relevance 4/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 4/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Motors - Hobby | |
Motors - Hobby - Brushed (Relevance 4/10)
|
Motors - Hobby - Brushless (Relevance 4/10)
|
Motors - Hobby - Brushless Packages (Relevance 4/10)
Brushless Systems including Motor and Electronic Speed Controller
|
Motors - Hobby - Rock Crawler (Relevance 4/10)
For slow moving rock crawlers. Motors only - speed controllers not included.
|
Motors - Hobby - Robotic - Appliances | |
Motors - DC 6mm Diameter (Relevance 4/10)
Our smallest motors at an affordable price.
Various models 10000 to 30000 rpm Low starting voltage of <0.8V Rated Voltage 1.3V 100 hours / 100000 turns mechanical life Less than 43 dB Mechanical Noise Level
|
Motors - DC 12.3X24.4 mm (Relevance 4/10)
M-300C Series 0.5 to 6 VDC - 1820 to 2700 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx. 22 grams.
|
Motors - DC 16.6X32.0 mm (Relevance 4/10)
M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 18.9X18.0X9.5 mm (Relevance 4/10)
M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams.
|
Motors - DC 20.0X25.0 mm (Relevance 4/10)
1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts
|
Motors - DC 23.6X25.0 mm (Relevance 4/10)
1.5 to 4.5 VDC - 12,500 RPM unloaded at 4.5 volts
|
Motors - DC 25.0X21.0 mm (Relevance 4/10)
M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 25.0x20.1X15.1 mm (Relevance 4/10)
M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X23.8 mm (Relevance 4/10)
M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X24.2X18.3 mm (Relevance 4/10)
MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 27.6X51.0 mm (Relevance 4/10)
Compact, high torque and reliable 16,200 RPM unloaded at 6 volts
|
Motors - DC 30.5X24.2 mm (Relevance 4/10)
M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 30.5X24.2X18.3 mm (Relevance 4/10)
MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 36.0X71.0 mm (Relevance 4/10)
High power, high speed 11,800 RPM unloaded at 12 volts
|
Motors - DC 42.0X78.0 mm (Relevance 4/10)
High power, high speed 18,800 to 20,000 RPM unloaded 6 volts to 12 volts
|
Motors - DC 42.0X85.0 mm (Relevance 4/10)
High power, high speed 9,700 RPM unloaded at 12 volts
|
Paint | |
Paints - Standard Spray - Tamiya (Relevance 4/10)
Cans of spray paint suitable for painting static models.
Tamiya spray colours provide an impressive finish to static models. When painting figures with a brush, it can be difficult to get paint into creases such as on faces and fabric. Using spray paint is a sure way to get a smooth, even finish. They are also extremely useful for painting large surfaces. Each can contains 100ml of paint, which is enough to fully cover 2 or 3, 1/24 scale sized car bodies. The paint is a synthetic lacquer that cures in a short period of time. Tamiya spray paints are not affected by acrylic or enamel paints. Therefore, following the painting of the entire assembly, details can be added or picked out using enamel and/or acrylic paints. By combining three different paints, the decoration of plastic models will become simpler and more effective.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 4/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Plastic - Hobby (Relevance 4/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Remote Control Aircraft | |
Micro Foam Plane - Hobby Zone (Relevance 4/10)
Indoor and Outdoor
Brands Include: Champ
|
Retaining Rings and Clips | |
Circlips - External - Basic (Standard) (Relevance 4/10)
Imperial and metric DIN471 / N1400 / D1460.
|
Servo Motors | |
Servomotors - Hobby - General (Relevance 4/10)
For cars, planes, boats and helicopters. JR, Spektrum, Futaba and Hitec
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Shaft and Shafting | |
Shafting - Ground - Hobby (Relevance 4/10)
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc Not recommended for use with precision steel or stainless steel bearings Some sizes have special features such as serrations or small barbs (noted in description). Unground ends Ideal for axles in robotic applications and educational projects
|
Springs | |
Springs - Compression - Standard (Relevance 4/10)
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
|
Unsorted | |
Accessories - Hobby - Unsorted (Relevance 4/10)
|
Wheels | |
Wheels - Hobby - Car - Rockcrawler Rims and Tyres (Relevance 4/10)
Rims and Tires for Axial Rockcrawlers, Losi Night crawler Comp Crawler.
|
Wheels and Tyres - Hobby - Car (Relevance 4/10)
1/36, 1/18, 1/10, 1/8 and 1/5 scale wheels and tires (tyres) Brands Proline, Axial, Nanda Venom and Laser
|
Fasteners | |
Locknuts (Relevance 3/10)
Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269.
|
Adhesives and Sealants | |
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Stainless Steel - 316L Grade (Relevance 1/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Economy (Relevance 1/10)
Taiwanese Hobby Bearings - Inexpensive Option. The type you find at most hobby shops.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - High Speed Cage (Relevance 1/10)
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
Bearings in this listing have various types of high speed cages. Speed ratings range from 20 percent to 80 percent increase on standard cage types. Please contact us for a data sheet on the specific size you require.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ceramic Hybrid (Relevance 1/10)
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
|
Bearings - Ceramic Si3N4 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Belts | |
Belts - Timing - 2.032mm Pitch - MXL (Relevance 1/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.073mm Pitch - 40DP (Relevance 1/10)
Standard Series Timing Belts 2.072mm or 0.08016 inch pitch.
Pitch (P) - 2.073mm (0.0816 inch). Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 1/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 9.525mm Pitch - L (Relevance 1/10)
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Pitch (P) - 9.525mm (0.200 inch). Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
|
Books and DVD | |
Books - Engineering (Relevance 1/10)
Machinery handbook contains standards, materials and other general engineering information.
|
Books - Robotics (Relevance 1/10)
Tips and tricks, maintenance and how-to guides. Includes industrial and hobby robotics.
|
Clamping and Locking | |
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Couplings | |
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Electrical | |
Power Supplies (Relevance 1/10)
24 V DC.
Standard : 24V DC Output, 110V AC input. Available on special order : 12V DC Output, 220/230V AC input.
|
Engines | |
Engines - Aircraft - OS (Relevance 1/10)
Engines for model aircraft.
Nitro hobby engines.
|
|
