Categories that include the terms: LEADSCREW and NUTS and METRIC and FLANGED and BRONZE
|
Linear Drive Systems - Leadscrew |  |
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 10/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 9/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 9/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 9/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nut Flanges for Acme Nuts (Relevance 6/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 6/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Leadscrews - Metric - Acme (Relevance 6/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 6/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Plain Bearings | |
Bushes - Bronze - Sintered - Flanged (Relevance 6/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bearings and Housings | |
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 5/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Fasteners | |
Nuts - Flange - Serrated (Relevance 5/10)
Stainless Steel.
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 4/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 4/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 4/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Belts | |
Belts - Timing - 5.000mm Pitch - GT - TRUE METRIC (Relevance 4/10)
GT Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Fasteners | |
Nuts - Aerotight (Relevance 4/10)
Aerotight is a Registered Trademark and can only be applied to goods manufactured by the Premier Screw and Repetition Company Limited. Any company infringing the registered trade mark may be liable to legal proceedings. Aerotight nuts should not be used on damaged or interrupted threads. When assembled on the screw at least two threads should protrude through the Aerotight nut. Advantages: Will not work loose. No other locking device needed.
|
Nuts - Blind (Relevance 4/10)
Blind nuts - Tee nuts.
|
Nuts - Cap - Stainless Steel (Relevance 4/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Hexagonal - Aluminium (Relevance 4/10)
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Binx (Relevance 4/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Hexagonal - Brass (Relevance 4/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 4/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 4/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 4/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Titanium - CP Grade 1 (Relevance 4/10)
METRIC. CP Grade 1.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Nuts - Quick Release (Relevance 4/10)
Carbon steel, black oxide finish. Button Thread® nuts allow quick fixturing on long thread lengths. Simply press the button and the threads are disengaged to allow easy movement up or down the screw. Release the button and the threads engage for normal turning.
|
Nuts - Well (Relevance 4/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Nuts - Wing - Stainless Steel (Relevance 4/10)
304 and 316 Stainless Wing Nuts
|
Nuts - Wing - Steel (Relevance 4/10)
Zinc Plated Wing Nuts
|
Pins - Taper - Metric (Relevance 4/10)
Metric Sizes 1:50 Taper
Metric Sizes to DIN 1.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Housing - Flanged (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 4/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Screws - Ball - Economy - Rolled - Nut Only (Relevance 4/10)
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
|
Linear Drive Systems - Leadscrew | |
Leadscrews - Imperial - Acme (Relevance 4/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Materials | |
Plates - Bronze - Sintered - Rectangular (Relevance 4/10)
SAE 841 Powdered metal bronze bearing plates.
Width and length are oversized and will finish to the dimensions shown. Thickness +/- 0.127mm.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 4/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Sintered Bronze (Relevance 4/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 4/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Sintered Bronze (Relevance 4/10)
Oil impregnated sintered bronze tubing - self lubricating.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on ID to allow for machining.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 4/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 4/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Solid (Relevance 4/10)
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Spherical - Sintered (Relevance 4/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 4/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Washers | |
Washers - Flat - Sintered Bronze - Precision (Relevance 4/10)
Flat washers from oil impregnated sintered bronze
|
Balls | |
Balls - Phosphor Bronze (Relevance 3/10)
Specific Gravity 8.4
|
Bearings | |
Bearings - Ball - Single Row - Radial - Flanged (Relevance 3/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Specialty | |
Bearings - Pivot - Flanged (Relevance 3/10)
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 3/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 3/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze (Relevance 3/10)
Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress.
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 3/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Castors | |
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Fasteners | |
Nuts - Dome - Nylon (Relevance 3/10)
Natural Nylon.
|
Nuts - Dome - Stainless Steel (Relevance 3/10)
Stainless Steel.
|
Nuts - Dome - Steel (Relevance 3/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Nylon (Relevance 3/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 3/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 3/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 3/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 3/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Thumb (Relevance 3/10)
|
Nuts - Wing - Nylon (Relevance 3/10)
|
Pins - Taper - Metric - Extractable - Internal Thread (Relevance 3/10)
1:50 Taper.
DIN 7978. Mild Steel.
|
Housings with Integral Bearing | |
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Housings - Bearing - Flanged - Square - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing : Igumid G. Ball : Highly wear resistant Iglidur W300.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 3/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - Offset - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - Round - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - Square - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Nuts - Bush Type (Relevance 3/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Materials | |
Sheet - Sintered Bronze (Relevance 3/10)
|
Plain Bearings | |
Bushes - Plastic - Iglidur G - Flanged (Relevance 3/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 3/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Shaft and Shafting | |
Supports - Flanged Two Bolt (Relevance 3/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings and Housings | |
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 1/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Belts | |
Belts - Timing - 2.000mm Pitch - GT - 3mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 6mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 9mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.500mm Pitch - T2.5 (Relevance 1/10)
T Series Metric Timing Belts.
Pitch (P) - 2.500mm. Tooth Length (T) - 1.50mm. Tooth Height (H) - 0.70mm. Belt Height (W) - 1.30mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 6mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 9mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - HTD (Relevance 1/10)
HTD Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.22mm. Belt Height (W) - 2.41mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - HTD (Relevance 1/10)
HTD Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - T5 (Relevance 1/10)
T Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.20mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Clamping and Locking | |
Collars - Shaft - With Integral Shim (Relevance 1/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Reducers - Bore (Relevance 1/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Couplings | |
Couplings - Bellows - Set Screw - Aluminium (Relevance 1/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Fasteners | |
Locknuts (Relevance 1/10)
Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269.
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Hex Head - Plastic (Relevance 1/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Hex Head - Steel (Relevance 1/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Large Shallow Head (Relevance 1/10)
UNC - UNF - METRIC - Various Materials.
|
Screws - Machine - Aluminium (Relevance 1/10)
Metal Thread Screws UNC.
Nuts sold separately - See Fasteners - Nuts.
|
Screws - Machine - Brass (Relevance 1/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Brass - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Nylon (Relevance 1/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - PEEK - Pan Head (Relevance 1/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Screws - Machine - Stainless Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Titanium CP1 (Relevance 1/10)
Metal Thread Screws - Metric. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Machine - Titanium CP1 - Countersunk Head (Relevance 1/10)
Flat Head Countersunk. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Socket - Button - Alloy Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Aluminium (Relevance 1/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Zinc Plated (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Alloy Steel (Relevance 1/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Aluminium (Relevance 1/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Nylon (Relevance 1/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Screws - Socket - Cap - Stainless (Relevance 1/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Titanium (Relevance 1/10)
METRIC. CP Grade 1.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Zinc Plated (Relevance 1/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Aluminium (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Socket Set Screws - Cup Point - Standard (Relevance 1/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Threaded Rod - Allthread - Brass (Relevance 1/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 1/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 1/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Gearboxes | |
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 1/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 1/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 1/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 1/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Handles and Knobs | |
Knobs - Ball - Knock On - Phenolic (Relevance 1/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Hobby Accessories | |
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Hobby Condensed Selection | |
Hobby Gears - Spur - Module 0.4 (Relevance 1/10)
A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.
|
Hobby Gears - Spur - Module 0.5 (Relevance 1/10)
A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Die Cast (Relevance 1/10)
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
|
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 1/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Insert Bearings and Housings | |
Bearings - For Cast Iron Housings (Relevance 1/10)
With spherical OD for use with cast iron flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.
|
Bearings - For Pressed Metal Housings (Relevance 1/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Kits | |
Assortment Kits - Various (Relevance 1/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Diameter (Relevance 1/10)
16mm Diameter with pitches 2.5 to 20mm. Machined or unmachined ends. Nuts sold seperately.
Material : Cf53 induction hardened to HRC 62 (=/- 2). Pitch accuracy : <= 0.1mm / 300mm ISO class 7. Nuts sold seperately.
|
Screws - Ball - 16mm Housing - Base Type (Relevance 1/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - Economy - Rolled - Screw Only (Relevance 1/10)
Match with nut. Accuracy T7 50µm/300mm.
Longer lengths available on request (up to 5600mm). Steel Cf53 or Cf60 induction hardened and polished. Running trach hardened to 60 HRC. Profile: Gothic type rolled. Accuracy T7 50µm/300mm.
|
|
