Categories that include the terms: LEADSCREWS and METRIC and ACME
|
Linear Drive Systems - Leadscrew |  |
Leadscrew Nut Flanges for Acme Nuts (Relevance 10/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 10/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 10/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 10/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 10/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 10/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Imperial - Acme (Relevance 10/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Acme (Relevance 10/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 10/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Belts | |
Belts - Timing - 5.000mm Pitch - GT - TRUE METRIC (Relevance 5/10)
GT Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Fasteners | |
Pins - Taper - Metric (Relevance 5/10)
Metric Sizes 1:50 Taper
Metric Sizes to DIN 1.
|
Pins - Taper - Metric - Extractable - Internal Thread (Relevance 4/10)
1:50 Taper.
DIN 7978. Mild Steel.
|
Belts | |
Belts - Timing - 2.000mm Pitch - GT - 3mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 6mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 9mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.500mm Pitch - T2.5 (Relevance 1/10)
T Series Metric Timing Belts.
Pitch (P) - 2.500mm. Tooth Length (T) - 1.50mm. Tooth Height (H) - 0.70mm. Belt Height (W) - 1.30mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 6mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 9mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - HTD (Relevance 1/10)
HTD Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.22mm. Belt Height (W) - 2.41mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - HTD (Relevance 1/10)
HTD Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - T5 (Relevance 1/10)
T Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.20mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Clamping and Locking | |
Collars - Shaft - With Integral Shim (Relevance 1/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Reducers - Bore (Relevance 1/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Fasteners | |
Nuts - Hexagonal - Aluminium (Relevance 1/10)
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Brass (Relevance 1/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 1/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 1/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Titanium - CP Grade 1 (Relevance 1/10)
METRIC. CP Grade 1.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Hex Head - Plastic (Relevance 1/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Hex Head - Steel (Relevance 1/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Large Shallow Head (Relevance 1/10)
UNC - UNF - METRIC - Various Materials.
|
Screws - Machine - Brass (Relevance 1/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Brass - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Nylon (Relevance 1/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - Stainless Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Titanium CP1 (Relevance 1/10)
Metal Thread Screws - Metric. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Socket - Button - Alloy Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Aluminium (Relevance 1/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Zinc Plated (Relevance 1/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Alloy Steel (Relevance 1/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Aluminium (Relevance 1/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Nylon (Relevance 1/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Screws - Socket - Cap - Stainless (Relevance 1/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Titanium (Relevance 1/10)
METRIC. CP Grade 1.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Zinc Plated (Relevance 1/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Aluminium (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Socket Set Screws - Cup Point - Standard (Relevance 1/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Threaded Rod - Allthread - Brass (Relevance 1/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 1/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 1/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Handles and Knobs | |
Knobs - Ball - Knock On - Phenolic (Relevance 1/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Hobby Condensed Selection | |
Hobby Gears - Spur - Module 0.4 (Relevance 1/10)
A small selection of popular Module 0.4 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.4 spur gear with 20 teeth has a pitch diameter of 8mm. A module 0.4 spur gear with 10 teeth has a pitch diameter of 4mm.
|
Hobby Gears - Spur - Module 0.5 (Relevance 1/10)
A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth
See main listings under Gears for sizes not listed here To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.
|
Retaining Rings and Clips | |
Circlips - External - Basic (Standard) (Relevance 1/10)
Imperial and metric DIN471 / N1400 / D1460.
|
Circlips - Internal - Basic (Relevance 1/10)
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS.
Many sizes can also be ordered in Zinc Plated or Stainless Steel. Tolerances on request. Standard and heavy duty options.
|
E-Clips - Basic (Relevance 1/10)
Basic imperial and metric e-clips DIN6799 and N1500.
Not all e-clips are exactly the same style, however all follow the basic principal of a push on clip.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 1/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - PTFE Lined (Relevance 1/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Tools | |
Tools - Thread Repair (Relevance 1/10)
Quickly repairs damaged screws
Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.
|
|
