Categories that include the terms: LINEAR and SLIDE and DRYLIN and ACCESSORIES
|
Linear Motion Bearings - Drylin |  |
Linear Slide - Drylin - Carriage Assembly (Relevance 10/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 10/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 7/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 7/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Batteries | |
Batteries - Accessories (Relevance 4/10)
Miscellaneous battery accessories - Lipo safety charge sacks - Balancers - Leads - Etc
|
Engines | |
Engines - Steam - Wilesco - Accessories (Relevance 4/10)
|
Fuel | |
Fuel - Accessories (Relevance 4/10)
Includes fuel tanks for World Model Aircraft
|
Hobby Accessories | |
Accessories - Hobby - Body Clips (Relevance 4/10)
Large and small body clips. Fluoro or standard. Plastic coated or anodised. Range of colours. Bent and straight.
|
Accessories - Hobby - General (Relevance 4/10)
General hobby supplies
Velcro Strip - ESC Fans - Heat Shrink - Motor Cooling Stands - Spring Dyno Camera Eye - Tuning Mat - Frequency Keys
|
Accessories - Servo Programmer - Digital HFP20 (Relevance 4/10)
Servo programmer-tester for Hitec digital servos
|
Crystals - Remote Control (Relevance 4/10)
|
Dubro Accessories Listed by Description (Relevance 4/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Glow Plugs (Relevance 4/10)
Real McCoy, OS glow plugs and Super Tiger
|
Glow Starter Kits (Relevance 4/10)
Starter pack. Fuel Bottel, 4 in 1 spanner, glow starter and charger
|
Glow Starters (Relevance 4/10)
|
Gyros - Hobby (Relevance 4/10)
Hitec and more
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x
|
Leads and Connectors - Hobby (Relevance 4/10)
Adaptor leads for batteries, battery chargers, servos and receivers including Tamiya, Deans and Losi plugs.
Includes Deans and T Connectors
|
Propeller Hubs (Relevance 4/10)
|
Propellers - Boat (Relevance 4/10)
|
Propellers - Plane - Electric - Folding (Relevance 4/10)
|
Propellers - Plane - Electric - Slow Fly (Relevance 4/10)
|
Propellers - Plane - Electric - Standard (Relevance 4/10)
|
Propellers - Plane - Nitro - 2 Blade (Relevance 4/10)
|
Propellers - Plane - Nitro - 3 Blade (Relevance 4/10)
|
Propellers - Plane - Nitro - 4 Blade (Relevance 4/10)
|
Receivers and Accessories (Relevance 4/10)
Receivers for Radio Control Equipment - Spektrum and Futaba
|
Speed Controllers - Aircraft (Relevance 4/10)
|
Speed Controllers - Car and Buggy (Relevance 4/10)
|
Speed Controllers - Marine (Relevance 4/10)
|
Spinners - 2 Blade (Relevance 4/10)
Spinners for aircraft propellers
|
Spinners - 3 Blade (Relevance 4/10)
Spinners for aircraft propellers
|
Tape - Double Sided (Relevance 4/10)
Double Sided Foam Tape
|
Tape - Glass Fibre (Relevance 4/10)
Hinge tape and other uses
|
Wire - Silicone (Relevance 4/10)
Silicone Wire in various colours and gauges
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Diameter (Relevance 4/10)
16mm Diameter with pitches 2.5 to 20mm. Machined or unmachined ends. Nuts sold seperately.
Material : Cf53 induction hardened to HRC 62 (=/- 2). Pitch accuracy : <= 0.1mm / 300mm ISO class 7. Nuts sold seperately.
|
Screws - Ball - 16mm Housing - Base Type (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Housing - Flanged (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 4/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Screws - Ball - Economy - Rolled - Nut Only (Relevance 4/10)
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
|
Screws - Ball - Economy - Rolled - Screw Only (Relevance 4/10)
Match with nut. Accuracy T7 50µm/300mm.
Longer lengths available on request (up to 5600mm). Steel Cf53 or Cf60 induction hardened and polished. Running trach hardened to 60 HRC. Profile: Gothic type rolled. Accuracy T7 50µm/300mm.
|
Screws - Ball - Thomson Saginaw (Relevance 4/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nut Flanges for Acme Nuts (Relevance 4/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 4/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Imperial - Acme (Relevance 4/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Acme (Relevance 4/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 4/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 4/10)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed) (Relevance 4/10)
For running on shafts fixed at the ends.
|
Model Kit Accessories | |
Model Kit Abrasives (Relevance 4/10)
For a professional finish
|
Model Kit Cement (Relevance 4/10)
Tamiya nd Mr Hobby Glue for plastic model kits
|
Model Kit Knives (Relevance 4/10)
Cutting tools, Excel knife blades and handles, razor saws.
|
Model Kit Masking Tape (Relevance 4/10)
Various sizes
|
Model Kit Paint Brushes (Relevance 4/10)
Paint brushes for finishing plastic model kits
|
Model Kit Paint Thinners (Relevance 4/10)
Thinners for enamel and acrylic paints
|
Model Kit Paints - Acrylic (Relevance 4/10)
Water Based paints for model kits
|
Model Kit Paints - Enamel (Relevance 4/10)
Oil based paints for model kits
|
Model Kit Paints - Textured (Relevance 4/10)
Texture paint for great looking dioramas
|
Model Kit Polishing Compound (Relevance 4/10)
For a professional finish
|
Model Kit Primers and Cleaners (Relevance 4/10)
For surface preparation prior to painting
|
Model Kit Putty (Relevance 4/10)
For a professional finish
|
Model Kit Tools (Relevance 4/10)
Stands, Line Tracing Kit, Applicators, Cleaning Brushes
|
Model Kit Weathering Materials (Relevance 4/10)
For a professional finish
|
Remote Control Boats | |
RC Boat Accessories (Relevance 4/10)
|
Rocketry | |
Rockets - Accessories (Relevance 4/10)
Rocketry accessories. Wadding, ignitors, nose cones, shock cords, parachutes etc.
|
Servo Motors | |
Servomotor Accessories (Relevance 4/10)
Cases, gears and horns to suit popular servos
|
Tools | |
Tools - Nitro Engine Starter and Accessories (Relevance 4/10)
Pocket staters, Bump Starts and belts
|
Unsorted | |
Accessories - Hobby - Unsorted (Relevance 4/10)
|
Balls | |
Balls - Bored - Plastic (Relevance 1/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Castors | |
Ball Transfer Units - Screw Stem (Relevance 1/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Frelon Lined (Relevance 1/10)
Self aligning. Open or closed. Precision or standard. For rotating and linear motion.
|
Magnets | |
Magnets - Rare Earth - Plated (Relevance 1/10)
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 Deg C to 93 Deg C. Size tolerances +/- 0.13
|
Motors - DC - MAX Series | |
Motors - DC - MAX 40 (Relevance 1/10)
Precious metal brush commutation system. See Gearheads - Ondrives - MAX Series for matching gearheads.
Operating Temperature Range: -30°C to +85°C (Max. rotor temperature +85°C), Mass: 187g. Low inductance - much longer brush life and low electrical noise. Low inertia - low mechanical time constant for fast acceleration and high speed stability. High efficiency - low current consumption, ideal for battery powered applications. Linear speed torque characteristics - simple accurate control ideal for servo applications.
|
Rocketry | |
Rockets - Rockets only (Relevance 1/10)
Rockets only including Ready to Fly and Build Kits. All accessories required.
RTF = Ready to Fly No Assembly Required E2X = Easy to Assemble Level 1 = Requires some painting, gluing and sanding. Assembly may take several hours. Level 2 = Beginner skills in model rocket construction and finishing. More complex designs. Assembly may take several days. Level 3 = Advanced kits. Moderate skills in model rocket construction and finishing. Unfinished body tubes. Very complex designs. Assembly may take several days.
|
Shaft and Shafting | |
Supports - Flanged Two Bolt (Relevance 1/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 1/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
|
