Categories that include the terms: LUBRICANTS and SHOCK and OIL
|
Lubricants |  |
Lubricants - Shock Oil (Relevance 10/10)
Model Engines, Losi, ND Power Racing, Venom
Viscosity is listed in Centistokes along with an approximate weight grade following in brackets.
|
Lubricants - Air Filter Oil (Relevance 9/10)
|
Lubricants - Diff Gear Oil (Relevance 9/10)
Model Engines, Losi, ND Power Racing, Venom
|
Lubricants - General (Relevance 5/10)
Various brands and types. Includes Inox, Lanox, Anti-Seize, Cutting Fluid, Chain Lube, Moly Lube, Food Grade, PTFE Lubes, Silicone and more
Some items in this category are marked as only available for collection. Includes high temperature and food grade lubes. Battery Conditioner - Oils - Moisture Inhibitor - WD - Valve and Oring Lubricant
|
Seals and Sealing | |
Oil Seals - Automotive (Relevance 5/10)
Automotive Oil Seals.
|
Oil Seals - Nitrile Rubber (Relevance 5/10)
DIN 3760 - General purpose grease and oil sealing.
Operating Temp. Range: -30°C to +90°C. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.
|
Fuel | |
Fuel - Oil Mix (Relevance 4/10)
Note! Hobby Fuel is for collection at our counter only. Dangerous goods charges are too expensive for sending these goods out.
Oil mixes for blending with Nitro and Methanol. RC cars and helicopter fuels Includes Coolpower synthetic oil and first pressing Castor oil
|
Lubricants | |
Lubricants - After Run (Relevance 4/10)
See main listings for sizes not shown here.
|
Kites | |
Kites - Parafoil (Relevance 3/10)
Parafoils are reliable and tear resistant. They are strutless so no assembly is required.
|
Kites - Parafoil 63x140 cm (Relevance 3/10)
Parafoils are reliable and tear resistant. They are strutless so no assembly is required.
|
Retaining Rings and Clips | |
R-Clips - Double Coil (Relevance 3/10)
Also known as internal hitch pins, bridge pins or humpback pins
|
R-Clips - Single Coil (Relevance 3/10)
Also known as internal hitch pins, bridge pins or humpback pins
|
Shim | |
Shim and Foil - Aluminium (Relevance 3/10)
Includes listing on 6061-T6 Aluminium Sheet. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Brass (Relevance 3/10)
Brass shim sheet. Very thin foil to thick sizes. Also one assortment pack listed.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes strips, sheets and rolls.
|
Shim and Foil - Copper (Relevance 3/10)
Shim sheet. Very thin foil to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Stainless Steel (Relevance 3/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Steel (Relevance 3/10)
Shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 1/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Fasteners | |
Screws - Machine - PEEK - Pan Head (Relevance 1/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Gears and Gearing | |
Gears - Racks - Flexible (Relevance 1/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Materials | |
Rod - Round - Sintered Bronze (Relevance 1/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Tube - Round - Sintered Bronze (Relevance 1/10)
Oil impregnated sintered bronze tubing - self lubricating.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on ID to allow for machining.
|
Model Kit Accessories | |
Model Kit Paints - Enamel (Relevance 1/10)
Oil based paints for model kits
|
Mounts and Vibration Control | |
Dampeners - Bushings - Silicone (Relevance 1/10)
Protects fragile subjects from micro-vibrations and light shocks.
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
|
Mounts - Centre Bolt - Solo Unitised (Relevance 1/10)
Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.
|
Paint | |
Paint - Polycarbonate Spray - Tamiya (Relevance 1/10)
Cans of polycarbonate spray paint developed especially for decorating transparent polycarbonate bodies used in R/C car modeling.
Each can contains 100ml of paint, which is the appropriate amount for finishing a model. Paint the body from the inside, keeping the can about 30cm from the surface. After curing, apply another coat. Small details should be brush painted beforehand using Tamiya bottle paints for polycarbonate. These paints are impervious to oil and fuels, so they can be safely used on gas-powered R/C bodies. Never use these paints on plastic models.
|
Plain Bearings | |
Bushes - Bronze - Sintered - Flanged (Relevance 1/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 1/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Spherical - Sintered (Relevance 1/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Rocketry | |
Rockets - Accessories (Relevance 1/10)
Rocketry accessories. Wadding, ignitors, nose cones, shock cords, parachutes etc.
|
Seals and Sealing | |
O-Rings - Cord (Relevance 1/10)
Nitrile and Fluoroelastomer continuous length o-ring cord.
Nitrile: Temp Range: -30°C to +90°C / Fluoroelastomer: Temp Range -20°C to +240°C. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Nitrile: Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. Fluoroelastomer: Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis.
|
O-Rings - Nitrile Rubber (Relevance 1/10)
General purpose.
Temperature Range: -30°C to +90°C. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.
|
O-Rings - Silicone Rubber (Relevance 1/10)
High thermal resistance and cold flexibility.
Temperature Range: -70°C to +200°C. Good dialectric properties and resistance to ozone and oxygen attack. Retains flexibility at high and low temperatures. Poor strength and tear resistance. Poor resistance to oils, fuels, concentrated acids and alkalis, water and steam.
|
Tools | |
Tools - General (Relevance 1/10)
Needle Files, Pin Vises, Gear Gauge, Wire and Tube Benders, Tube Cutters, Miniature tap, Turnbuckle Wrench, Shock Matching Tool and die set
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more
|
Washers | |
Washers - Flat - Sintered Bronze - Precision (Relevance 1/10)
Flat washers from oil impregnated sintered bronze
|
|
