Categories that include the terms: MAGNETS and ALNICO and SIDE and POLE and ROTATOR
|
Magnets |  |
Magnets - Alnico - Bar (Relevance 6/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Minor Magnet (Relevance 5/10)
Supplied with keeper
|
Magnets - Alnico - Pocket Magnet (Relevance 5/10)
Supplied with keeper
|
Magnets - Alnico - Rod - Sintered (Relevance 5/10)
|
Magnets - Bar (Relevance 4/10)
Great hobby and educational magnets for learning about magnetic attraction
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Magnets - Ferrite (Relevance 4/10)
Small ferrite magnets with good pulling strength.
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Magnets - Rare Earth - Plated (Relevance 4/10)
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 Deg C to 93 Deg C. Size tolerances +/- 0.13
|
Magnets - Rare Earth - Shielded (Relevance 4/10)
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures
|
Magnets - Alcomax - Rectangular Bar (Relevance 3/10)
No keepers
|
Magnets - Ceramic Blocks (Relevance 3/10)
Low cost, light weight, high energy material
Non conductive hard brittle material Performs best at temperatures below 249 Deg C Can be cut with a diamond wheel Difficult to grind and can't be machined or drilled by normal methods Tolerance 0.13mm on all dimensions
|
Magnets - Ceramic Ring (Relevance 3/10)
|
Magnets - Rubber and Vinyl (Relevance 3/10)
Magnetic Vinyl Sheets and Magnetic Rubber Strip
|
Materials |  |
Materials - Magnetic Sheeting (Relevance 3/10)
Magnetic sheeting is ideal for making small decorative magnets or for use on vehicles.
If cared for properly this magnetic material will not damage paintwork. Magnets should be removed weekly and the vehicle washed before re-applying Type 1: White on one side and magnetic on the other. Ordered per metre. Type 2: Rectangular sheets sticky on one side and magnetic on the other. Sheeting will be supplied in one length up to the max continuous length shown in the tables
|
Hobby Accessories |  |
Tape - Double Sided (Relevance 1/10)
Double Sided Foam Tape
|
Mounts and Vibration Control |  |
ISO-PAD - Sheets (Relevance 1/10)
For shimming and mounting machinery bases to isolate vibration.
Orange in colour. Patterned and unpatterned types. Tough vinyl chloride elastomeric resin bonded to both sides of a core of monofilament fibreglass. Co-efficient of friction 0.8. Temp range -35 Deg C to 110 Deg C.
|
Suspension Units - Rubber - Square - Insert Type (Relevance 1/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Stepper Motors - Hybrid |  |
Motors - Stepper - Hybrid - Nema Size 11 (Relevance 1/10)
Mounting hole centres 23.10 mm (+/- 0.2 mm) - Body Width 28.00 mm.
Refer PDF Link at bottm of internet page for sizes and wiring information. Hybrid Stepper Motors include a permanent magnet in the rotor.
|
Tools |  |
Hobby Tools - General (Relevance 1/10)
Flywheel Rench, Allen Key Set, Socket Driver Se, 4-way cross wrench, pioin stocker, ball end pliers, side cutters, long nose pliers, flat nose pliers, pinion storage, hobby scissors and body reamer.
See main listings for sizes not shown here.
|
No more categories match your selection
|