Categories that include the terms: MAGNETS and RARE and EARTH and PLATED
|
Magnets |  |
Magnets - Rare Earth - Plated (Relevance 10/10)
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 Deg C to 93 Deg C. Size tolerances +/- 0.13
|
Magnets - Rare Earth - Shielded (Relevance 10/10)
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures
|
Fasteners | |
Pins - Clevis - Zinc Plated (Relevance 4/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Zinc Plated (Relevance 4/10)
Split pins.
|
Pins - Roll - Zinc Plated (Relevance 4/10)
Zinc plated spring steel DIN1481.
|
Screws - Socket - Button - Zinc Plated (Relevance 4/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Zinc Plated (Relevance 4/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Keys and Keysteel | |
Keys - Gib Head - Zinc Plated (Relevance 4/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Magnets | |
Magnets - Alcomax - Rectangular Bar (Relevance 4/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 4/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Minor Magnet (Relevance 4/10)
Supplied with keeper
|
Magnets - Alnico - Pocket Magnet (Relevance 4/10)
Supplied with keeper
|
Magnets - Alnico - Rod - Sintered (Relevance 4/10)
|
Magnets - Bar (Relevance 4/10)
Great hobby and educational magnets for learning about magnetic attraction
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Magnets - Ceramic Blocks (Relevance 4/10)
Low cost, light weight, high energy material
Non conductive hard brittle material Performs best at temperatures below 249 Deg C Can be cut with a diamond wheel Difficult to grind and can't be machined or drilled by normal methods Tolerance 0.13mm on all dimensions
|
Magnets - Ceramic Ring (Relevance 4/10)
|
Magnets - Ferrite (Relevance 4/10)
Small ferrite magnets with good pulling strength.
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Magnets - Rubber and Vinyl (Relevance 4/10)
Magnetic Vinyl Sheets and Magnetic Rubber Strip
|
Materials | |
Materials - Magnetic Sheeting (Relevance 3/10)
Magnetic sheeting is ideal for making small decorative magnets or for use on vehicles.
If cared for properly this magnetic material will not damage paintwork. Magnets should be removed weekly and the vehicle washed before re-applying Type 1: White on one side and magnetic on the other. Ordered per metre. Type 2: Rectangular sheets sticky on one side and magnetic on the other. Sheeting will be supplied in one length up to the max continuous length shown in the tables
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 1/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Clutches and Brakes | |
Clutches - Slip - Inline (Relevance 1/10)
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
|
Fasteners | |
Joints - Clevis - Steel (Relevance 1/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Nuts - Dome - Steel (Relevance 1/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Steel (Relevance 1/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Steel (Relevance 1/10)
Zinc Plated Wing Nuts
|
Pins - Clevis - Self Locking (Relevance 1/10)
No need for cotter pins
Self locking and reusable with a spring loaded ball lock Plated steel with stainless steel ball
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Machine - Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Studs - Ball - Threaded (Relevance 1/10)
Zinc Plated Steel DIN 71803 Form C Surface Hardened to 55 HRC (Ball (D1) Only - Thread is Not Hardened)
|
Threaded Rod - Allthread - Steel (Relevance 1/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Single Assembly (Relevance 1/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Single Assembly - Circlip Retained (Relevance 1/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Mounts and Vibration Control | |
Adjusters - Rigid (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Mild steel bright zinc plated. Screwdriver cross recess in base.
|
Adjusters - Tilt (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25° from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.
|
Mounts - Cylindrical - Square (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
|
Mounts - Finger Flex Assemblies (Relevance 1/10)
Cadmium Plated Steel Housing. Natural Rubber Isolators. Natural Frequency 6-30 Hz.
|
Mounts - Square (Relevance 1/10)
Fastener may be steel, brass or zinc plated. Natural rubber isolator.
|
Retaining Rings and Clips | |
Circlips - Internal - Basic (Relevance 1/10)
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS.
Many sizes can also be ordered in Zinc Plated or Stainless Steel. Tolerances on request. Standard and heavy duty options.
|
Springs | |
Springs - Extension (Relevance 1/10)
Zinc Plated Spring Steel not recommended for applications exceeding 121 Deg C (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 Deg C (500 Deg F). 302 stainless steel is slightly magnetic.
|
Stepper Motors - Hybrid | |
Motors - Stepper - Hybrid - Nema Size 11 (Relevance 1/10)
Mounting hole centres 23.10 mm (+/- 0.2 mm) - Body Width 28.00 mm.
Refer PDF Link at bottm of internet page for sizes and wiring information. Hybrid Stepper Motors include a permanent magnet in the rotor.
|
Washers | |
Washers - Nord Lock (Relevance 1/10)
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer.
|
|
