Categories that include the terms: MAGNETS and RARE and EARTH and SHIELDED
|
Magnets |  |
Magnets - Rare Earth - Plated (Relevance 10/10)
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 Deg C to 93 Deg C. Size tolerances +/- 0.13
|
Magnets - Rare Earth - Shielded (Relevance 10/10)
Insulator shield prevents loss of magnetic flux when inserted into steel components or fixtures
Shielded magnets supply holding forces in limited areas of steel tools, dies and fixtures
|
Magnets - Alcomax - Rectangular Bar (Relevance 4/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 4/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Minor Magnet (Relevance 4/10)
Supplied with keeper
|
Magnets - Alnico - Pocket Magnet (Relevance 4/10)
Supplied with keeper
|
Magnets - Alnico - Rod - Sintered (Relevance 4/10)
|
Magnets - Bar (Relevance 4/10)
Great hobby and educational magnets for learning about magnetic attraction
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Magnets - Ceramic Blocks (Relevance 4/10)
Low cost, light weight, high energy material
Non conductive hard brittle material Performs best at temperatures below 249 Deg C Can be cut with a diamond wheel Difficult to grind and can't be machined or drilled by normal methods Tolerance 0.13mm on all dimensions
|
Magnets - Ceramic Ring (Relevance 4/10)
|
Magnets - Ferrite (Relevance 4/10)
Small ferrite magnets with good pulling strength.
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Magnets - Rubber and Vinyl (Relevance 4/10)
Magnetic Vinyl Sheets and Magnetic Rubber Strip
|
Materials |  |
Materials - Magnetic Sheeting (Relevance 3/10)
Magnetic sheeting is ideal for making small decorative magnets or for use on vehicles.
If cared for properly this magnetic material will not damage paintwork. Magnets should be removed weekly and the vehicle washed before re-applying Type 1: White on one side and magnetic on the other. Ordered per metre. Type 2: Rectangular sheets sticky on one side and magnetic on the other. Sheeting will be supplied in one length up to the max continuous length shown in the tables
|
Bearings - Thrust |  |
Bearings - Thrust - Ball (Relevance 1/10)
3 Piece Thrust Bearings, Shielded and Unshielded.
|
Bearings and Housings |  |
Housings - Bearing - Pillow Block - Miniature (Relevance 1/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Stepper Motors - Hybrid |  |
Motors - Stepper - Hybrid - Nema Size 11 (Relevance 1/10)
Mounting hole centres 23.10 mm (+/- 0.2 mm) - Body Width 28.00 mm.
Refer PDF Link at bottm of internet page for sizes and wiring information. Hybrid Stepper Motors include a permanent magnet in the rotor.
|
No more categories match your selection
|