Categories that include the terms: MOUNTS and SPRING and SUSPENSION and SINGLE and HOLE
|
Mounts and Vibration Control |  |
Suspension Units - Rubber - Square - Insert Type (Relevance 5/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Economy (Relevance 4/10)
Taiwanese Hobby Bearings - Inexpensive Option. The type you find at most hobby shops.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Flanged (Relevance 4/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 4/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 4/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Belt and Sprockets - Posi-Drive | |
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core (Relevance 4/10)
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Tracks with Mounting Holes (Relevance 4/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 4/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Single Assembly (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Single Assembly - Circlip Retained (Relevance 4/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Materials | |
Wire - Steel - Spring - Music Wire (Relevance 4/10)
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
|
Mounts and Vibration Control | |
Mounts - Centre Bolt - Solo Unitised (Relevance 4/10)
Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.
|
Reels | |
Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 4/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Reels - Spring Powered - Base Mounted - Steel (Relevance 4/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Springs | |
Plungers - Spring - Smooth (Relevance 4/10)
Stainless Steel or Plastic - No Thread.
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
|
Spring Assemblies - Bracket - RINO (Relevance 4/10)
Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.
|
Spring Assemblies - Small Bracket - RINO (Relevance 4/10)
Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
|
Spring Motor Assemblies - Open - RINO (Relevance 4/10)
Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.
Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.
|
Spring Motor Assemblies - SDP (Relevance 4/10)
Base Mounted.
Base Mounted. Springs : 301 Stainless Steel.
|
Springs - Compression - Conical (Relevance 4/10)
Conical 302 Stainless steel springs
Solid height lower than a standard compression spring due to the conical shape Ends are closed Starting rate is the same as the kg/mm rate
|
Springs - Compression - Standard (Relevance 4/10)
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
|
Springs - Constant Force (Relevance 4/10)
Mounting hole specifications will be supplied on request. Free ID may vary to meet load specification.
|
Springs - Extension (Relevance 4/10)
Zinc Plated Spring Steel not recommended for applications exceeding 121 Deg C (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 Deg C (500 Deg F). 302 stainless steel is slightly magnetic.
|
Springs - Torsion - Left Hand Wound (Relevance 4/10)
Left Hand Wound. 180 Deg. Deflection. Right hand wound and special springs are available on special order.
|
Washers | |
Washers - Disc Spring - Plastic (Relevance 4/10)
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 4/10)
Flat Carbon Spring Steel Washers.
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 3/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 3/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 3/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Clamping and Locking | |
Shaftloc-tm Sleeves - Single Ended (Relevance 3/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Fasteners | |
Joints - Clevis - Spring Clips (Relevance 3/10)
Made from 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). See also yokes.
|
Sleeves - Hex Hole (Relevance 3/10)
|
Sleeves - Square Hole - Plain (Relevance 3/10)
|
Games | |
Games - Puzzles - Single Player (Relevance 3/10)
If you like or challenge or know someone who does, these puzzles will keep the grey matter occupied.
Group includes Tantrix, Roll-A-Maze, Air Traffic Control, Bucky Balls, Crazy Cheeze, Heist, Hide and Seek Safari, IQ Puzzler IQ Twist, Magic Cube, Magnetic twist Puzzles, Penguins on Ice, Pixelate, Sink or Swim, Utopia
|
Housings with Integral Bearing | |
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 3/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Materials | |
Tube - Square - Carbon Fibre - Round Hole (Relevance 3/10)
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Tube - Square - Carbon Fibre - Square Hole (Relevance 3/10)
High impact light weight carbon fibre tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Mounts and Vibration Control | |
Adjusters - Rigid (Relevance 3/10)
Adjustable supports for all kinds of machinery.
Mild steel bright zinc plated. Screwdriver cross recess in base.
|
Adjusters - Tilt (Relevance 3/10)
Adjustable supports for all kinds of machinery.
Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25° from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.
|
Dampeners - Bushings - Silicone (Relevance 3/10)
Protects fragile subjects from micro-vibrations and light shocks.
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
|
Dampeners - Double Studded - Silicone (Relevance 3/10)
Damps low frequency vibrations.
Use for compression only.
|
ISO-PAD - Sheets (Relevance 3/10)
For shimming and mounting machinery bases to isolate vibration.
Orange in colour. Patterned and unpatterned types. Tough vinyl chloride elastomeric resin bonded to both sides of a core of monofilament fibreglass. Co-efficient of friction 0.8. Temp range -35 Deg C to 110 Deg C.
|
Mounts - Cylindrical - Female to Blank (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Female to Female (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Blank (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Female (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Male (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Square (Relevance 3/10)
Rubber hardness 60 Duro Standard unless otherwise noted
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
|
Mounts - Finger Flex Assemblies (Relevance 3/10)
Cadmium Plated Steel Housing. Natural Rubber Isolators. Natural Frequency 6-30 Hz.
|
Mounts - Leveling - Base Type - Round (Relevance 3/10)
For loads of 45 to 5350 kg.
|
Mounts - Plate Style (Relevance 3/10)
Refer pdf file at ftp://ftp.minibearings.com.au/mounts/MPS_Platemounts_Loads.pdf.
|
Mounts - Square (Relevance 3/10)
Fastener may be steel, brass or zinc plated. Natural rubber isolator.
|
Pulleys | |
Pulleys - Vee - A / 4L - Single Row - Through Bore (Relevance 3/10)
|
Pulleys - Vee - M / 3L - Single Row - Through Bore (Relevance 3/10)
|
Pulleys - Vee - Y / 2L - Single Row - Through Bore (Relevance 3/10)
|
Retaining Rings and Clips | |
R-Clips - Single Coil (Relevance 3/10)
Also known as internal hitch pins, bridge pins or humpback pins
|
Shaft and Shafting | |
Shafts - Flexible - Panel Mount - Cased (Relevance 3/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Open (Relevance 3/10)
See PDF file at bottom of internet page for Performance Data.
|
Springs | |
Plungers - Spring - Threaded (Relevance 3/10)
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
|
Posts - Spring (Relevance 3/10)
|
Spring Motors - SDP (Relevance 3/10)
301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.
|
Springs - Compression - Metre Lengths (Relevance 3/10)
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
|
Springs - Extension - Metre Lengths (Relevance 3/10)
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
|
Springs - Torsion - Right Hand Wound (Relevance 3/10)
Right Hand Wound.
|
Washers | |
Washers - Disc Spring - Carbon Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Disc Spring - Stainless Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Lock - External Tooth - Spring Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Spring (Relevance 3/10)
Wave Washers - All Materials.
|
Batteries | |
Batteries - Standard (Relevance 1/10)
The Venom standard non-rechargeable battery range includes AA, AAA, C, D and 9V non-rechargeable.
Bulk packs and single cards
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 1/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Clamping and Locking | |
Collars - Shaft - Gripfast (Relevance 1/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Reducers - Bore (Relevance 1/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Fasteners | |
Inserts - Expansion (Relevance 1/10)
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Pins - Clevis - Self Locking (Relevance 1/10)
No need for cotter pins
Self locking and reusable with a spring loaded ball lock Plated steel with stainless steel ball
|
Pins - Dowel - Extractable (Relevance 1/10)
Hardened and Ground Steel 100 Cr6 to DIN 7979, m6 Dia. Tolerance.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Roll - Plain (Relevance 1/10)
Plain carbon spring steel DIN1481.
|
Pins - Roll - Zinc Plated (Relevance 1/10)
Zinc plated spring steel DIN1481.
|
Socket Set Screws - Rolling Ball Tip (Relevance 1/10)
Rolling ball tip for locating into a hole
|
Yoke Ends - Blank (Relevance 1/10)
Linkage Connectors with blank ends - no hole
Drop forged steel machined to SAE standards Also see clevis joints
|
Gears and Gearing | |
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Hinges | |
Hinges - Flexi-Hinge - Precision (Relevance 1/10)
Double and Single Ended - Limited Angle Rotary Applications.
Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature.
|
Hobby Accessories | |
Accessories - Hobby - General (Relevance 1/10)
General hobby supplies
Velcro Strip - ESC Fans - Heat Shrink - Motor Cooling Stands - Spring Dyno Camera Eye - Tuning Mat - Frequency Keys
|
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Square - Miniature (Relevance 1/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Insert Bearings and Housings | |
Bearings - For Cast Iron Housings (Relevance 1/10)
With spherical OD for use with cast iron flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.
|
Kites | |
Kites - Singleline Kites (Relevance 1/10)
|
Kits | |
Assortment Kits - Various (Relevance 1/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Levers | |
Levers - Control Handles - Flat (Relevance 1/10)
Steel Parts: Quality class 5.8. Ball Knob: Black duroplastic FS31 / Surface Finish: Black oxide. Can be used for simpler clamping applications and switching operations. If necessary there must be enough space to turn the handle through an angle of 360°. The star drive hole model is designed to allow turning in steps of 45°.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Materials | |
Sheet - Styrene (Relevance 1/10)
Styrene (ABS) plastic sheet in single sheets and bulk packs
|
Pulleys | |
Pulleys - Timing - 2.000mm Pitch - GT - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 2.032mm Pitch - MXL - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 2.500mm Pitch - T2.5 - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 3.000mm Pitch - HTD - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 5.000mm Pitch - HTD - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 5.080mm Pitch - XL - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 10.000mm Pitch - T10 - STOCK (Relevance 1/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Retaining Rings and Clips | |
Circlips - External - Grooveless (Relevance 1/10)
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
|
Spiral Rings - External - Heavy Duty (Relevance 1/10)
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2
|
Spiral Rings - Internal - Heavy Duty (Relevance 1/10)
Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2
|
Spiral Rings - Internal - Medium Duty (Relevance 1/10)
Includes AI / WH / AS3217 / RR / MIL-R-27426B1 - Spring Steel and Stainless Steel.
Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AI, Smalley: WH, Spirolox and Ramsey: RR, Aerospace AS3217, MIL-R-27426B1
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 1/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Stepper Motors - Hybrid | |
Motors - Stepper - Hybrid - Nema Size 11 (Relevance 1/10)
Mounting hole centres 23.10 mm (+/- 0.2 mm) - Body Width 28.00 mm.
Refer PDF Link at bottm of internet page for sizes and wiring information. Hybrid Stepper Motors include a permanent magnet in the rotor.
|
Tools | |
Tools - Pin Wrench (Relevance 1/10)
Used on nuts with two holes.
Constructed of special blued steel.
|
Universal Joints | |
Covers - Universal Joint - Elasticate Rubber (Relevance 1/10)
For Single and Double Universal Joints.
-27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent).
|
Washers | |
Washers - Lock - Tabbed - Heavy Duty (Relevance 1/10)
Heavy duty WH / TW Series for bearing locknuts.
Carbon spring steel. Use with NH series locknuts.
|
Washers - Safety (Relevance 1/10)
Spring Steel Hardened Black.
|
Worms and Worm Gears | |
Worm Gears - 24 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 1) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 2) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 2) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 3) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
25 Degree Pressure Angle - 15.95 Degree Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 2) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 6) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
25 Degree Pressure Angle - 14.2 Degree Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 64 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.5 (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.18 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 1) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 2) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 1) - Metallic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 1) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 2) - Plastic (Relevance 1/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
|
