Categories that include the terms: OIL and SEALS and NITRILE and RUBBER
|
Seals and Sealing |  |
O-Rings - Nitrile Rubber (Relevance 10/10)
General purpose.
Temperature Range: -30°C to +90°C. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.
|
Oil Seals - Nitrile Rubber (Relevance 10/10)
DIN 3760 - General purpose grease and oil sealing.
Operating Temp. Range: -30°C to +90°C. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.
|
O-Rings - Silicone Rubber (Relevance 7/10)
High thermal resistance and cold flexibility.
Temperature Range: -70°C to +200°C. Good dialectric properties and resistance to ozone and oxygen attack. Retains flexibility at high and low temperatures. Poor strength and tear resistance. Poor resistance to oils, fuels, concentrated acids and alkalis, water and steam.
|
Oil Seals - Automotive (Relevance 7/10)
Automotive Oil Seals.
|
V-Rings - Nitrile (Relevance 7/10)
VA Profile - Nitrile V Rings.
|
Castors | |
Castors - Black Rubber (Relevance 4/10)
Black rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Castors - Blue Non Marking Rubber (Relevance 4/10)
Blue non-marking rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Couplings | |
Couplings - Jaw Type - With Rubber Spider (Relevance 4/10)
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Educational Projects | |
Kits - Rubber Band Powered (Relevance 4/10)
These kits are designed to teach kids about physics.
|
Fuel | |
Fuel - Oil Mix (Relevance 4/10)
Note! Hobby Fuel is for collection at our counter only. Dangerous goods charges are too expensive for sending these goods out.
Oil mixes for blending with Nitro and Methanol. RC cars and helicopter fuels Includes Coolpower synthetic oil and first pressing Castor oil
|
Lubricants | |
Lubricants - Air Filter Oil (Relevance 4/10)
|
Lubricants - Diff Gear Oil (Relevance 4/10)
Model Engines, Losi, ND Power Racing, Venom
|
Lubricants - Shock Oil (Relevance 4/10)
Model Engines, Losi, ND Power Racing, Venom
Viscosity is listed in Centistokes along with an approximate weight grade following in brackets.
|
Magnets | |
Magnets - Rubber and Vinyl (Relevance 4/10)
Magnetic Vinyl Sheets and Magnetic Rubber Strip
|
Mounts and Vibration Control | |
Suspension Units - Rubber - Square - Insert Type (Relevance 4/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Seals and Sealing | |
O-Rings - Cord (Relevance 4/10)
Nitrile and Fluoroelastomer continuous length o-ring cord.
Nitrile: Temp Range: -30°C to +90°C / Fluoroelastomer: Temp Range -20°C to +240°C. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Nitrile: Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids. Fluoroelastomer: Suitable for synthetic and hydraulic fluids, strong acids, steam, many chemicals and many alkalis.
|
Rings - Backup (Relevance 4/10)
Durometer 90 Nitrile Rubber back up rings.
|
Sealing Plugs - Stainless (Relevance 4/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Shim | |
Shims - Rubber (Relevance 4/10)
Handy non marring soft spacer shims in a wedge shape
Level and stabilise appliances, desks, tables, filing cabinets, machinery Stackable. Vibration cushioning. Ribs ensure that wedges grab tight and stay in place Black ridid wedges can support up to 2000 lbs White flexible wedges can be trimmed with a utility knife
|
Toys | |
Toys - Planes - Rubber Band and Throwing (Relevance 4/10)
Inexpensive foam gliders, planes and Twirly Propellers
|
Universal Joints | |
Covers - Universal Joint - Elasticate Rubber (Relevance 4/10)
For Single and Double Universal Joints.
-27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent).
|
Washers | |
Washers - Flat - Rubber (Relevance 4/10)
|
Adhesives and Sealants | |
Adhesives - Dope (Relevance 3/10)
|
Adhesives - Fishing (Relevance 3/10)
|
Adhesives - General (Relevance 3/10)
Molytec, Loctite, Pacer, Dow Corning, 3M. Includes silicone sealant, gasket adhesive, canopy glue, belt conditioner and electronic tak-pak.
Some items in this category are marked as only available for collection.
|
Epoxies (Relevance 3/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Retaining Compounds (Relevance 3/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Solder (Relevance 3/10)
|
Super Bonders (Relevance 3/10)
Mercury, ZAP, Molytec, Loctite, Pacer, Pro Seal. Cyanoacrylate adhesives for quick bonding. Products for foam Kicker, wood, metals, rubber and plastics.
Some items in this category are marked as only available for collection.
|
Threadlockers (Relevance 3/10)
ZAP, Molytec, Loctite, Pacer. Pipe sealant, low to high strength threadlockers. Hydraulic threadlocker. Wick-In. Stops threads loosening from vibration.
Some items in this category are marked as only available for collection.
|
Kites | |
Kites - Parafoil (Relevance 3/10)
Parafoils are reliable and tear resistant. They are strutless so no assembly is required.
|
Kites - Parafoil 63x140 cm (Relevance 3/10)
Parafoils are reliable and tear resistant. They are strutless so no assembly is required.
|
Retaining Rings and Clips | |
R-Clips - Double Coil (Relevance 3/10)
Also known as internal hitch pins, bridge pins or humpback pins
|
R-Clips - Single Coil (Relevance 3/10)
Also known as internal hitch pins, bridge pins or humpback pins
|
Shim | |
Shim and Foil - Aluminium (Relevance 3/10)
Includes listing on 6061-T6 Aluminium Sheet. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Brass (Relevance 3/10)
Brass shim sheet. Very thin foil to thick sizes. Also one assortment pack listed.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Includes strips, sheets and rolls.
|
Shim and Foil - Copper (Relevance 3/10)
Shim sheet. Very thin foil to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Stainless Steel (Relevance 3/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Shim and Foil - Steel (Relevance 3/10)
Shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 1/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 1/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Gears and Gearing | |
Gears - Racks - Flexible (Relevance 1/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Lubricants | |
Lubricants - General (Relevance 1/10)
Various brands and types. Includes Inox, Lanox, Anti-Seize, Cutting Fluid, Chain Lube, Moly Lube, Food Grade, PTFE Lubes, Silicone and more
Some items in this category are marked as only available for collection. Includes high temperature and food grade lubes. Battery Conditioner - Oils - Moisture Inhibitor - WD - Valve and Oring Lubricant
|
Materials | |
Rod - Round - Sintered Bronze (Relevance 1/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Rod - Round - Urethane (Relevance 1/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Tube - Round - Sintered Bronze (Relevance 1/10)
Oil impregnated sintered bronze tubing - self lubricating.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on ID to allow for machining.
|
Model Kit Accessories | |
Model Kit Paints - Enamel (Relevance 1/10)
Oil based paints for model kits
|
Mounts and Vibration Control | |
Mounts - Centre Bolt - Solo Unitised (Relevance 1/10)
Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.
|
Mounts - Cylindrical - Female to Blank (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Female to Female (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Blank (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Female (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Male (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Square (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
|
Mounts - Finger Flex Assemblies (Relevance 1/10)
Cadmium Plated Steel Housing. Natural Rubber Isolators. Natural Frequency 6-30 Hz.
|
Mounts - Square (Relevance 1/10)
Fastener may be steel, brass or zinc plated. Natural rubber isolator.
|
Paint | |
Paint - Polycarbonate Spray - Tamiya (Relevance 1/10)
Cans of polycarbonate spray paint developed especially for decorating transparent polycarbonate bodies used in R/C car modeling.
Each can contains 100ml of paint, which is the appropriate amount for finishing a model. Paint the body from the inside, keeping the can about 30cm from the surface. After curing, apply another coat. Small details should be brush painted beforehand using Tamiya bottle paints for polycarbonate. These paints are impervious to oil and fuels, so they can be safely used on gas-powered R/C bodies. Never use these paints on plastic models.
|
Plain Bearings | |
Bushes - Bronze - Sintered - Flanged (Relevance 1/10)
Oil impregnated flanged sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Sintered - Unflanged (Relevance 1/10)
Oil impregnated sintered bronze bushes.
Precision items show an allowable Load Speed Rating in Newtons times RPM.
|
Bushes - Bronze - Spherical - Sintered (Relevance 1/10)
Spherical OD Oil Impregnated Sintered Bronze Bushes.
ID and OD oversized. Enquire if details required.
|
Storage | |
Straps - Cargo (Relevance 1/10)
Black rubber cargo straps with hooks. Stronger but less flexible than bungee straps.
|
Washers | |
Washers - Flat - Sintered Bronze - Precision (Relevance 1/10)
Flat washers from oil impregnated sintered bronze
|
Wheels | |
Wheels - Industrial - Budget (Relevance 1/10)
Inexpensive white plastic wheels with black rubber tires and small rubber wheels with aluminum hubs
General Duty Ideal for trolleys, lawn mowers and other Plain Centre
|
|
