Categories that include the terms: PINS and COTTER and ZINC and PLATED
|
Fasteners |  |
Pins - Clevis - Zinc Plated (Relevance 10/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Zinc Plated (Relevance 10/10)
Split pins.
|
Pins - Roll - Zinc Plated (Relevance 10/10)
Zinc plated spring steel DIN1481.
|
Pins - Cotter - Plain (Relevance 7/10)
Split pins.
|
Pins - Cotter - Stainless Steel (Relevance 7/10)
Split pins.
|
Screws - Socket - Button - Zinc Plated (Relevance 7/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Zinc Plated (Relevance 7/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Keys and Keysteel | |
Keys - Gib Head - Zinc Plated (Relevance 7/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Fasteners | |
Pins - Clevis - Adjustable (Relevance 4/10)
Multihole clevis pins for quick and easy adjustments
Made from 1010, 1018 or 1022 steel
|
Pins - Clevis - Plain (Relevance 4/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Self Locking (Relevance 4/10)
No need for cotter pins
Self locking and reusable with a spring loaded ball lock Plated steel with stainless steel ball
|
Pins - Clevis - Stainless Steel 304 (Relevance 4/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 4/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Dowel - Extractable (Relevance 4/10)
Hardened and Ground Steel 100 Cr6 to DIN 7979, m6 Dia. Tolerance.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650
|
Pins - Dowel - Standard - Hardened Steel (Relevance 4/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 4/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Hammer Drive - Flat Head (Relevance 4/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 4/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hitch - External (Relevance 4/10)
Also known as R-Clips.
|
Pins - Roll - Plain (Relevance 4/10)
Plain carbon spring steel DIN1481.
|
Pins - Roll - Stainless Steel (Relevance 4/10)
304 and 420 grades DIN1481.
|
Pins - Spirol (Relevance 4/10)
|
Pins - Taper - Imperial - Miniature (Relevance 4/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Miniature sizes. Stainless and Mild Steel.
|
Pins - Taper - Imperial - Standard (Relevance 4/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Pins - Taper - Metric (Relevance 4/10)
Metric Sizes 1:50 Taper
Metric Sizes to DIN 1.
|
Pins - Taper - Metric - Extractable - Internal Thread (Relevance 4/10)
1:50 Taper.
DIN 7978. Mild Steel.
|
Pins - Wire Lock Lynch - Double Wire - Round (Relevance 4/10)
|
Roll Pins - Hobby (Relevance 4/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Magnets | |
Magnets - Rare Earth - Plated (Relevance 4/10)
Incredibly strong attraction and repulsion. Neodymium-Iron-Boron encased in nickel jackets to protect the brittle magnet material and prevent corrosion.
High strength to weight ratios. Commonly used in miniature applications such as linear actuators, sensing applications, gyroscopes, flow meters, recording devices, pacemakers and alternators. Temperature range -73 Deg C to 93 Deg C. Size tolerances +/- 0.13
|
Tools | |
Tools - Pin Wrench (Relevance 4/10)
Used on nuts with two holes.
Constructed of special blued steel.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 3/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 3/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Syncro - L-Shaped (Relevance 3/10)
|
Collars - Shaft - Clamp Type (Relevance 3/10)
|
Collars - Shaft - Fairloc (Relevance 3/10)
|
Collars - Shaft - Gripfast (Relevance 3/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Standard (Relevance 3/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Collars - Shaft - With Integral Shim (Relevance 3/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Hubs - Bolt On (Relevance 3/10)
Aluminium Hub with Set Screws
|
Insulators - Screw (Relevance 3/10)
Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.
|
Reducers - Bore (Relevance 3/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Rings - Tolerance (Relevance 3/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Shaftloc-tm Simple Type M (Relevance 3/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 3/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Fasteners | |
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 3/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Screws - Self Tapping - Countersunk Head (Relevance 3/10)
Countersunk screws length includes head. ie, the full overall length of the screw.
|
Screws - Self Tapping - For Plastics (Relevance 3/10)
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics Be sure to select correct screw for hard or soft plastic threadcutting
|
Screws - Self Tapping - Pan Head (Relevance 3/10)
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
|
Hobby Accessories | |
Spinners - 2 Blade (Relevance 3/10)
Spinners for aircraft propellers
|
Spinners - 3 Blade (Relevance 3/10)
Spinners for aircraft propellers
|
Shaft and Shafting | |
Shafts - Pinion (Relevance 3/10)
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 1/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Clutches and Brakes | |
Clutches - Slip - Inline (Relevance 1/10)
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
|
Couplings | |
Couplings - Double Disk (Relevance 1/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
Couplings - Double Disk - High Torque (Relevance 1/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Fasteners | |
Joints - Ball and Socket - Right Angle (Relevance 1/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Joints - Clevis - Plastic (Relevance 1/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Joints - Clevis - Steel (Relevance 1/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Nuts - Dome - Steel (Relevance 1/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Steel (Relevance 1/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Steel (Relevance 1/10)
Zinc Plated Wing Nuts
|
Screws - Machine - Steel (Relevance 1/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Studs - Ball - Threaded (Relevance 1/10)
Zinc Plated Steel DIN 71803 Form C Surface Hardened to 55 HRC (Ball (D1) Only - Thread is Not Hardened)
|
Threaded Rod - Allthread - Steel (Relevance 1/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Games | |
Games - Amusement (Relevance 1/10)
Fun inexpensive little gadgets and gizmos to keep the kids amused for hours
Lava drops, water snakes, pin art Voic changer, Juggling balls Magic eight ball
|
Gears and Gearing | |
Gears - Mitre - Module 1 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Zinc die cast and steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Hobby Accessories | |
Speed Controllers - Aircraft (Relevance 1/10)
|
Speed Controllers - Car and Buggy (Relevance 1/10)
|
Speed Controllers - Marine (Relevance 1/10)
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Single Assembly (Relevance 1/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with a bearing fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings - Bearing - Single Assembly - Circlip Retained (Relevance 1/10)
Includes bearings.
Housing: 080 M40 (C45) Steel Zinc Plated Natural. Bearing: Steel Shields: (ZZ) Steel. Bearing housings are supplied with bearings and circlips fitted. Bearing adhesive may be used during assembly. Fixing using H holes for a capscrew fixing or THD tapped hole to fasten from the opposite direction.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Die Cast (Relevance 1/10)
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
|
Keys and Keysteel | |
Keys - Keysteel Lengths - Rectangular (Relevance 1/10)
Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.
|
Keys - Keysteel Lengths - Square (Relevance 1/10)
Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.
|
Kits | |
Assortment Kits - Various (Relevance 1/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Levers | |
Levers - Clamp (Relevance 1/10)
Steel Parts: Quality class 5.8. Handle: Diecast zinc to DIN 1743 or Glass fibre reinforced plastic with toothed wheel in diecast zinc. Surface Finish: Handle plastic coated. Steel parts black oxide finish.
|
Levers - Clamp - Quick Release (Relevance 1/10)
Handles: Die-cast zinc or plastic. Internal thread: mechanism made from carbon steel. The thru-hole clamping lever allows for quick clamping on long thread lengths.
|
Materials | |
Rod - Round - Bronze - LG2 (Standard) (Relevance 1/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 1/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Mounts and Vibration Control | |
Adjusters - Rigid (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Mild steel bright zinc plated. Screwdriver cross recess in base.
|
Adjusters - Tilt (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25° from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.
|
Mounts - Cylindrical - Square (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
|
Mounts - Finger Flex Assemblies (Relevance 1/10)
Cadmium Plated Steel Housing. Natural Rubber Isolators. Natural Frequency 6-30 Hz.
|
Mounts - Square (Relevance 1/10)
Fastener may be steel, brass or zinc plated. Natural rubber isolator.
|
Plain Bearings | |
Bushes - Bronze - Hobby (Relevance 1/10)
A small selection of popular sizes. Solid precision LG2 bronze bushes.
See main listings for sizes not shown here. ID Tolerance : -0.0127 / +0.040 --- OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Bushes - Bronze - Solid (Relevance 1/10)
Solid precision LG2 bronze bushes.
ID Tolerance : -0.0127 / +0.040. OD Tolerance : +0.060 / +0.102. LENGTH Tolerance : -0.254 / +0.254. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. Hardness : 70-90 BHN.
|
Pulleys | |
Pulleys - U Groove - Steel (Relevance 1/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Remote Control Equipment | |
Controllers - Hand (Relevance 1/10)
Transmitters. Includes Spektrum, JR, E-Sky, digital and analogue radio control equipment.
|
Retaining Rings and Clips | |
Circlips - Internal - Basic (Relevance 1/10)
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS.
Many sizes can also be ordered in Zinc Plated or Stainless Steel. Tolerances on request. Standard and heavy duty options.
|
R-Clips - Double Coil (Relevance 1/10)
Also known as internal hitch pins, bridge pins or humpback pins
|
R-Clips - Single Coil (Relevance 1/10)
Also known as internal hitch pins, bridge pins or humpback pins
|
Rollers | |
Bearings - Pressure Roller - With Urethane OD (Relevance 1/10)
Bearings with Urethane Tyre on OD for applications requiring frictional movement.
For applications including paper and card dispensing and rolling (eg ATM Machines).
|
Rollers - Idler - Stainless Steel (Relevance 1/10)
|
Rollers - Idler - With Aluminium Sleeve (Relevance 1/10)
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
|
Rollers - Idler - With Sintered Bearing (Relevance 1/10)
|
Rollers - Nylon Tyre (Relevance 1/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Rollers - Steel (Relevance 1/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Rollers - Track - With Inner Race (Relevance 1/10)
|
Rollers - Urethane Feed - With Hub (Relevance 1/10)
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter Sleeve - Aluminium
|
Rollers - Yoke - Cam (Relevance 1/10)
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking
Polycoated shore 80A cast urethane cover
|
Springs | |
Springs - Extension (Relevance 1/10)
Zinc Plated Spring Steel not recommended for applications exceeding 121 Deg C (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 Deg C (500 Deg F). 302 stainless steel is slightly magnetic.
|
Tools | |
Tools - General (Relevance 1/10)
Needle Files, Pin Vises, Gear Gauge, Wire and Tube Benders, Tube Cutters, Miniature tap, Turnbuckle Wrench, Shock Matching Tool and die set
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more
|
Universal Joints | |
Universal Joints - Steel (Relevance 1/10)
Steel - Cast Zinc - Stainless Steel.
|
Washers | |
Washers - Nord Lock (Relevance 1/10)
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer.
|
|
