Plungers Spring Smooth Double Ended - Hobby And Engineering Parts

Categories that include the terms: PLUNGERS and SPRING and SMOOTH and DOUBLE and ENDED Springs Plungers - Spring - Smooth (Relevance 8/10) Stainless Steel or Plastic - No Thread. Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright. Plungers - Spring - Threaded (Relevance 5/10) Items shown with Long-Lok have a dry threadlocking sealant applied to thread. Belt and Sprockets - Posi-Drive Belts - Posi-Drive - 3.75 mm Circular Pitch - Double Core (Relevance 4/10) Same as US 0.1475 Pitch - Use with Posi-Drive Sprockets. Use Double Core with Posi-Drive Sprockets. 3.746mm Circular Pitch. Same as US 0.1475 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined Belts - Posi-Drive - 4.00 mm Circular Pitch - Double Core (Relevance 4/10) Same as US 20 Pitch - Use with Posi-Drive Sprockets. Use Double Core with Posi-Drive Sprockets. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined Hobby Accessories Tape - Double Sided (Relevance 4/10) Double Sided Foam Tape Materials Wire - Steel - Spring - Music Wire (Relevance 4/10) SAE 1090 Spring Steel. Shipped in straight lengths on wood backing board. Springs Spring Assemblies - Bracket - RINO (Relevance 4/10) Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables. Spring Assemblies - Small Bracket - RINO (Relevance 4/10) Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. Spring Motor Assemblies - Open - RINO (Relevance 4/10) Budget Assemblies. Average fatigue life of 5000 to 30000 cycles. Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles. Spring Motor Assemblies - SDP (Relevance 4/10) Base Mounted. Base Mounted. Springs : 301 Stainless Steel. Springs - Compression - Conical (Relevance 4/10) Conical 302 Stainless steel springs Solid height lower than a standard compression spring due to the conical shape Ends are closed Starting rate is the same as the kg/mm rate Springs - Compression - Standard (Relevance 4/10) Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote. Springs - Extension (Relevance 4/10) Zinc Plated Spring Steel not recommended for applications exceeding 121 Deg C (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 Deg C (500 Deg F). 302 stainless steel is slightly magnetic. Springs - Torsion - Left Hand Wound (Relevance 4/10) Left Hand Wound. 180 Deg. Deflection. Right hand wound and special springs are available on special order. Washers Washers - Disc Spring - Plastic (Relevance 4/10) Also known as belleville washers. Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material. Washers - Flat - Carbon Spring Steel - Precision (Relevance 4/10) Flat Carbon Spring Steel Washers. Clamping and Locking Shaftloc-tm Sleeves - Single Ended (Relevance 3/10) Simple effective way to lock components onto shafts. 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Couplings Couplings - Double Disk (Relevance 3/10) Zero Backlash - High Torsional Stiffness. Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm. Couplings - Double Disk - High Torque (Relevance 3/10) Zero Backlash - Clamp Locking - Medium torsional stiffness. High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics. Fasteners Joints - Clevis - Spring Clips (Relevance 3/10) Made from 9SMn steel. Steel 9 SMn 28K (550-700 N/mm2). See also yokes. Pins - Wire Lock Lynch - Double Wire - Round (Relevance 3/10) Mounts and Vibration Control Dampeners - Double Studded - Silicone (Relevance 3/10) Damps low frequency vibrations. Use for compression only. Reels Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 3/10) Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture. Reels - Spring Powered - Base Mounted - Steel (Relevance 3/10) Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture. Retaining Rings and Clips R-Clips - Double Coil (Relevance 3/10) Also known as internal hitch pins, bridge pins or humpback pins Springs Posts - Spring (Relevance 3/10) Spring Motors - SDP (Relevance 3/10) 301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher. Springs - Compression - Metre Lengths (Relevance 3/10) Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310. Springs - Constant Force (Relevance 3/10) Mounting hole specifications will be supplied on request. Free ID may vary to meet load specification. Springs - Extension - Metre Lengths (Relevance 3/10) Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310. Springs - Torsion - Right Hand Wound (Relevance 3/10) Right Hand Wound. Washers Washers - Disc Spring - Carbon Steel (Relevance 3/10) Also known as belleville washers. Manufactured under strict quality control to conform to DIN 2093 Washers - Disc Spring - Stainless Steel (Relevance 3/10) Also known as belleville washers. Manufactured under strict quality control to conform to DIN 2093 Washers - Lock - External Tooth - Spring Steel (Relevance 3/10) Dimensions are nominal and may vary between batches. Washers - Lock - Internal Tooth - Spring Steel (Relevance 3/10) These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require. Dimensions are nominal and may vary between batches. Washers - Spring (Relevance 3/10) Wave Washers - All Materials. Bearings and Housings Housings - Bearing - Pillow Block - Miniature (Relevance 1/10) Aluminium pillow block housings mounted with 440C stainless miniature bearings No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination Belt and Sprockets - Posi-Drive Sprockets - Posi-Drive - 3.75 mm Circular Pitch (Relevance 1/10) Same as US 0.1475 Pitch - Use with Double Core Belts. Use with Double Core Posi-Drive Belts. 3.746mm Circular Pitch. Same as US 0.1475 Pitch. Sprockets - Posi-Drive - 4.00 mm Circular Pitch (Relevance 1/10) Same as US 20 Pitch - Use with Double Core Belts. Use with Double Core Posi-Drive Belts. 3.990mm Circular Pitch. Same as US 20 Pitch. Clamping and Locking Collars - Shaft - Gripfast (Relevance 1/10) Self Locking - Quick Release. 265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs. Fasteners Nuts - Hexagonal - Binx (Relevance 1/10) Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear. Pins - Clevis - Self Locking (Relevance 1/10) No need for cotter pins Self locking and reusable with a spring loaded ball lock Plated steel with stainless steel ball Pins - Roll - Plain (Relevance 1/10) Plain carbon spring steel DIN1481. Pins - Roll - Zinc Plated (Relevance 1/10) Zinc plated spring steel DIN1481. Games Games - Strategy (Relevance 1/10) Strategy Games including Wooden and other games. Ideal gifts for thinking people. Gobblet on the Go - Ringgz - Double Shutter - Eye of Horus - Khet - Tower of Kadesh - Giza - Dividends Jumping Java - Logan Stones - Hive - Army of Frogs - Quarto - Quixo - Quoridor - Batik - Pylos Skybridge - Inside - Eclipse - Gipf - Zertz - Dvonn - Yinsh - Punct - Tamsk - Abalone - Pentago - Columns Trinidad - Fire and Ice - Cityscape - Poison Pot - Zaroc - Megalith - Tantrix - Yikers Hinges Hinges - Flexi-Hinge - Precision (Relevance 1/10) Double and Single Ended - Limited Angle Rotary Applications. Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature. Hobby Accessories Accessories - Hobby - General (Relevance 1/10) General hobby supplies Velcro Strip - ESC Fans - Heat Shrink - Motor Cooling Stands - Spring Dyno Camera Eye - Tuning Mat - Frequency Keys Kits Assortment Kits - Various (Relevance 1/10) Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins Materials Rod - Round - Carbon Fibre (Relevance 1/10) High impact light weight carbon fibre for modelling. Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm Rod - Round - Glass Fibre (Relevance 1/10) High impact light weight glass fibre for modelling. Glass fibre rod is not smooth. Tube - Rectangular - Carbon Fibre (Relevance 1/10) High impact light weight carbon fibre hollow tubing for modelling. Pultruded carbon fibre with a smooth epoxy coated finish Tube - Round - Carbon Fibre (Relevance 1/10) High impact light weight carbon fibre hollow tubing for modelling. Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm Tube - Square - Carbon Fibre - Round Hole (Relevance 1/10) High impact light weight carbon fibre tubing for modelling. Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm Tube - Square - Carbon Fibre - Square Hole (Relevance 1/10) High impact light weight carbon fibre tubing for modelling. Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm Paint Paints - Standard Spray - Tamiya (Relevance 1/10) Cans of spray paint suitable for painting static models. Tamiya spray colours provide an impressive finish to static models. When painting figures with a brush, it can be difficult to get paint into creases such as on faces and fabric. Using spray paint is a sure way to get a smooth, even finish. They are also extremely useful for painting large surfaces. Each can contains 100ml of paint, which is enough to fully cover 2 or 3, 1/24 scale sized car bodies. The paint is a synthetic lacquer that cures in a short period of time. Tamiya spray paints are not affected by acrylic or enamel paints. Therefore, following the painting of the entire assembly, details can be added or picked out using enamel and/or acrylic paints. By combining three different paints, the decoration of plastic models will become simpler and more effective. Retaining Rings and Clips Circlips - External - Grooveless (Relevance 1/10) Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA. Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring. Spiral Rings - External - Heavy Duty (Relevance 1/10) AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel. Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2 Spiral Rings - Internal - Heavy Duty (Relevance 1/10) Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel. Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2 Spiral Rings - Internal - Medium Duty (Relevance 1/10) Includes AI / WH / AS3217 / RR / MIL-R-27426B1 - Spring Steel and Stainless Steel. Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AI, Smalley: WH, Spirolox and Ramsey: RR, Aerospace AS3217, MIL-R-27426B1 Storage Parts Boxes - Tilt Type (Relevance 1/10) Tilt pak plastic carry box with 4 self locking drawers Can be joined togetherto make a double sided case Freestanding or mountable 4 self locking drawers each with 4 compartments Universal Joints Covers - Universal Joint - Elasticate Rubber (Relevance 1/10) For Single and Double Universal Joints. -27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent). Washers Washers - Lock - Tabbed - Heavy Duty (Relevance 1/10) Heavy duty WH / TW Series for bearing locknuts. Carbon spring steel. Use with NH series locknuts. Washers - Safety (Relevance 1/10) Spring Steel Hardened Black. Wheels Wheels - Trolley - Soft Tyre (Relevance 1/10) Designed to fit standard supermarket trolley or industrial trolley wheel yokes. Quiet operation. Non marking. Smooth running. Worms and Worm Gears Worm Gears - 24 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 24 Pitch (Series 1) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 24 Pitch (Series 2) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 32 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 32 Pitch (Series 1) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 32 Pitch (Series 2) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 32 Pitch (Series 3) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 25 Degree Pressure Angle - 15.95 Degree Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 48 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 48 Pitch (Series 2) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 48 Pitch (Series 6) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 25 Degree Pressure Angle - 14.2 Degree Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - 64 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - Module 0.5 (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 3.18 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10) Match with metallic worms Module 0.80 Series 2. 20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 24 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 24 Pitch (Series 1) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 24 Pitch (Series 2) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 32 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 32 Pitch (Series 1) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 32 Pitch (Series 2) - Plastic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 32 Pitch (Series 3) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 25 Degree Pressure Angle - 15.95 Degree Lead Angle - 4 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 48 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 48 Pitch (Series 5) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 25 Degree Pressure Angle - 14.2 Degree Lead Angle - 4 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - 64 Pitch (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - Module 0.5 (Series 1) - Metallic (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 3.18 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10) Match with metallic worms Module 0.80 Series 2. 20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 1/10) Worms and Gears must be chosen from the same pitch and series to match. 20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear. Too many choices? You have selected to see ALL categories containing the terms PLUNGERS AND SPRING AND SMOOTH AND DOUBLE AND ENDED. Click here to see ONLY THE MOST POPULAR categories containing the terms PLUNGERS AND SPRING AND SMOOTH AND DOUBLE AND ENDED.

Cart total A$ 0.00 You may need to refresh the page if your selected currency doesn't change. Currency Options Default (USD) British Pound Canadian Dollar Euro Hong Kong Dollar Japanese Yen New Zealand Dollar Singapore Dollar US Dollar Swiss Francs You may need to refresh the page if your selected currency doesn't change. Item Popularity Show only popular categories Pictures Hide pictures Show all categories starting with A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9 Major Categories Adaptors Adhesives Aircraft Aircraft Parts Ansmann Parts Axial Parts Balls Bar Batteries Bearings Belts Bikes (Models) Boats Books (Hobby) Bushes Carbon Fibre Cars - Buggies - Truggies Car Parts Castors Ceramic Chain Circlips Clamps Collars Colt Parts Couplings Cranks Dental Bearings and Parts Dowel Pins Dragon Hobby Parts Drylin Dual Vee Dubro Parts DVD's (Hobby) Educational Products E-Flite Parts E-Sky Parts Engines Engine Parts Fishing Reel Bearings Fuel Games Gas Springs Gearboxes Gearmotors Gears Great Vigor Parts Handles Hangar 9 Parts Helicopters Helicopter Bearings Helicopter Parts Housings Hubs Joints Keysteel Knobs Kyosho Parts Lazy Susans Leadscrews Levers Linear Bearings Losi Parts Lubricants Materials Model Kits and Accessories Motors Mounts Mousetrap Vehicles MVVS Engine Parts Multiplex Parts Nuts O-Rings Oil Seals OS Engine Parts Paint Parkzone Parts Parts Boxes Pins Planes Plane Parts Pulleys Ratchets Reducers Rod Rod Ends Rollers Saito Parts Screws Shafting Sheet Shim Slides Solarbotics Solar Cells Spacers Sportwerks Parts Springs Sprockets Steam Boats and Engines Super Tigre Parts Surplus Specials Suspension Units Tamiya Parts Threaded Rod Tools Tube Universal Joints Venom Parts Vibration Mounts Washers Wheels Worms Zenoah Engine Parts SEARCH Product Description (Category) Information Search Part Number (ours) Part Number (other) Guided Search CATALOGUES Catalogues Index Catalogue A-Z Online Catalogues A-Z PDF Discount Registration Online Catalogue Quick Guides Surplus Stock   Adhesives Aircraft Aircraft Parts Ansmann Parts Axial Parts Bar Batteries Bearings Bikes (Models) Boats Books (Hobby) Carbon Fibre Cars - Buggies - Truggies Car Parts Ceramic Colt Parts Couplings Dental Bearings and Parts Dragon Hobby Parts Dubro Parts DVD's (Hobby) E-Flite Parts E-Sky Parts Engines Engine Parts Fishing Reel Bearings Fuel Games Gears Great Vigor Parts Hangar 9 Parts Helicopters Helicopter Bearings Helicopter Parts Hobbyzone Parts Kyosho Parts Losi Parts Materials Model Kits and Accessories Motors Mousetrap Vehicles Multiplex Parts MVVS Engine Parts OS Engine Parts Paint Parkzone Parts Parts Boxes PDF A-Z All Categories Planes Plane Parts Products Not Listed Here Saito Parts Screws Solar Cells Solarbotics Sportwerks Parts Steam Boats and Engines Super Tigre Parts Surplus Stock Specials Tamiya Parts Tools Tube Venom Parts Zenoah Engine Parts   Products Not Listed Above Quick Guides HOW TO & ABOUT US Charity Contact Us Frequently Asked Questions Freight Rates Home How To Order Online Mailorder Newsletter Subscription Order Specially Quoted Parts Payment Options Terms and Conditions of Sale PRODUCT INFORMATION Dental Bearings Hobby Information Information Sheets New Products Surplus Specials Lists Technical Information RECOMMENDED LINKS ACMA Radio Frequencies ACMA Frequencies Class License Couplings Information eParcel Tracking Express International Tracking Gearboxes Information Jokes and Trivia Materials Information Miniature Bearings Australia Ondrives UK Rino UK Shafting Information Shafting Information Stainless Selection Tingalpa Model Aero Club TNT Freight Tracking Unfair Contracts Wikipedia Windows to The Universe World Time

• Search for information pages instead of products
• Mail Order Form
• Order non-standard parts quoted by e-mail
• Freight Rates
• Terms of Sale

All care has been taken in the compilation of this page, however errors may occur. Please do not use the information contained herein for critical applications without first re-checking the information with an independent source. No responsibility will be accepted by Hobby & Engineering Supplies Pty Ltd or the Directors of said company for any loss of any kind that may be incurred in any way whatsoever from use of the information provided in these pages.

***** Trademarks *****

Delrin^TM is a registered trademark of duPont Corporation
Teflon^TM is a registered trademark of duPont Corporation

HES Terms and Conditions of Sale

HES Privacy Policy