Categories that include the terms: PULLEYS and FLAT and BELT and IDLER
|
Pulleys |  |
Pulleys - Flat Belt (Relevance 10/10)
Polycarbonate pulleys for flat belts 6mm or 6.35mm wide.
Aluminium Knurled Inserts. Gold Iridite Brass Knurled Inserts. Set Screw Locking.
|
Belts | |
Belts - Flat (Relevance 7/10)
Working Tension 2.3 to 27.5 N. Length Tolerance +/- 0.5%. Breaking Strength 1108 N. 1 Ply Polyester Woven Cord, Black Neoprene Coating. Maximum Belt Speed: 5000 mtrs / min (20000 feet / min).
|
Pulleys | |
Pulleys - Timing - 1.000mm Pitch - Suits 3mm Belts (Relevance 7/10)
Timing Pulleys to suit 1mm Pitch Timing Belts.
Aluminium Alloy
|
Pulleys - Timing - 1.000mm Pitch - Suits 6mm Belts (Relevance 7/10)
Timing Pulleys to suit 1mm Pitch Timing Belts.
Aluminium Alloy
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 3mm Wide Belts (Relevance 7/10)
Timing Pulleys to suit GT 2mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 6mm Wide Belts (Relevance 7/10)
Timing Pulleys to suit 2mm Pitch GT Timing Belts 6mm Wide.
Various materials as shown.
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 9mm Wide Belts (Relevance 7/10)
Timing Pulleys to suit 2mm Pitch GT Timing Belts 9mm Wide.
Aluminium Alloy
|
Pulleys - Timing - 3.000mm Pitch - GT - To Suit 6mm Wide Belts (Relevance 7/10)
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 6mm Wide.
Various materials as shown.
|
Pulleys - Timing - 3.000mm Pitch - GT - To Suit 9mm Wide Belts (Relevance 7/10)
Timing Pulleys to suit GT 3.000mm Pitch Timing Belts 9mm Wide.
Various materials as shown.
|
Pulleys - Timing - Idler (Relevance 7/10)
Complete with Needle Roller Bearing.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Pulleys - U Groove - Idler (Relevance 7/10)
Plastic and Steel with Steel Ball Bearings or Plain Bearings.
|
Belt and Sprockets - Posi-Drive | |
Belts - Posi-Drive - 3.75 mm Circular Pitch - Double Core (Relevance 4/10)
Same as US 0.1475 Pitch - Use with Posi-Drive Sprockets.
Use Double Core with Posi-Drive Sprockets. 3.746mm Circular Pitch. Same as US 0.1475 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Belts - Posi-Drive - 4.00 mm Circular Pitch - Double Core (Relevance 4/10)
Same as US 20 Pitch - Use with Posi-Drive Sprockets.
Use Double Core with Posi-Drive Sprockets. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Belts - Posi-Drive - 4.00 mm Circular Pitch - Single Core (Relevance 4/10)
Same as US 20 Pitch - Use with Posi-Drive Pulleys.
Use Single Core with Posi-Drive Pulleys. 3.990mm Circular Pitch. Same as US 20 Pitch. Posi-drive material lengths in this category can not be joined by the customer as special equipment is required. Material lengths are used in reciprocating applications and not meant to be joined
|
Sprockets - Posi-Drive - 3.75 mm Circular Pitch (Relevance 4/10)
Same as US 0.1475 Pitch - Use with Double Core Belts.
Use with Double Core Posi-Drive Belts. 3.746mm Circular Pitch. Same as US 0.1475 Pitch.
|
Sprockets - Posi-Drive - 4.00 mm Circular Pitch (Relevance 4/10)
Same as US 20 Pitch - Use with Double Core Belts.
Use with Double Core Posi-Drive Belts. 3.990mm Circular Pitch. Same as US 20 Pitch.
|
Belts | |
Belt Tension Tester (Relevance 4/10)
For testing the tension on assembled timing belts, vee belts, flat belts etc.
Gauges for testing all types of belts when assembled for correct tension.
|
Belts - Rounthane (Relevance 4/10)
Joinable belting.
Join with Rounthane Connectors. Material : Non Slip Polyurethane. Use with grooved idler pulleys or 6.35mm Top Width V Pulleys. Purchased per 305mm (1 foot). Orders for more than 1 foot will be supplied as a continuous length.
|
Belts - Rounthane - Connectors (Relevance 4/10)
Joinable belting connectors.
|
Belts - Timing - 1.000mm Pitch (Relevance 4/10)
Miniature 1mm series timing belts
Pitch (P) - 1.000mm Tooth Height (H) - 0.41mm. Belt Height (W) - 0.97mm Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 3mm Wide (Relevance 4/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 6mm Wide (Relevance 4/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 9mm Wide (Relevance 4/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.032mm Pitch - MXL (Relevance 4/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.073mm Pitch - 40DP (Relevance 4/10)
Standard Series Timing Belts 2.072mm or 0.08016 inch pitch.
Pitch (P) - 2.073mm (0.0816 inch). Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.500mm Pitch - T2.5 (Relevance 4/10)
T Series Metric Timing Belts.
Pitch (P) - 2.500mm. Tooth Length (T) - 1.50mm. Tooth Height (H) - 0.70mm. Belt Height (W) - 1.30mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 6mm Wide (Relevance 4/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - GT - 9mm Wide (Relevance 4/10)
GT Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.14mm. Belt Height (W) - 2.41mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 3.000mm Pitch - HTD (Relevance 4/10)
HTD Series Metric Timing Belts.
Pitch (P) - 3.000mm. Tooth Height (H) - 1.22mm. Belt Height (W) - 2.41mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - GT - TRUE METRIC (Relevance 4/10)
GT Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 1.93mm. Belt Height (W) - 3.81mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - HTD (Relevance 4/10)
HTD Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Height (H) - 2.08mm. Belt Height (W) - 3.81mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.000mm Pitch - T5 (Relevance 4/10)
T Series Metric Timing Belts.
Pitch (P) - 5.000mm. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.20mm. Belt Height (W) - 2.20mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 4/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 9.525mm Pitch - L (Relevance 4/10)
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Pitch (P) - 9.525mm (0.200 inch). Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - Lengths (Relevance 4/10)
Sold per meter - Refer diagrams in timing belt listings for aspects of various pitches.
Lengths of timing belt stock are used for reciprocating applications. Not meant to be joined.
|
Belts - Vee - 5.0 x 3.0 mm (Relevance 4/10)
Miniature and small belts. 5.0mm Top Width x 3.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.0 x 4.0 mm - Y (Relevance 4/10)
Miniature and small belts. 6.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 6.4 x 4.1 mm - 2L (Relevance 4/10)
Miniature and small belts. 6.4mm Top Width x 4.1mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 8.0 x 4.0 mm (Relevance 4/10)
Miniature and small belts. 8.0mm Top Width x 4.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 9.7 x 8.0 mm - SPZ (Relevance 4/10)
Miniature and small belts. 9.7mm Top Width x 8.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 5.5 mm - M/3L (Relevance 4/10)
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 6.0 mm - Z (Relevance 4/10)
Miniature and small belts. 10.0mm Top Width x 6.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.5 x 9.0 mm - A/4L (Relevance 4/10)
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.7 x 10.0 mm - SPA (Relevance 4/10)
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.3 x 13.0 mm - SPB (Relevance 4/10)
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.5 x 11.0 mm - B/5L (Relevance 4/10)
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 31.5 x 19.0 mm - D (Relevance 4/10)
31.5mm Top Width x 19.0mm Height.
Sizes are nominal and may vary slightly.
|
Fasteners | |
Pins - Hammer Drive - Flat Head (Relevance 4/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Socket Set Screws - Flat Ball Tip (Relevance 4/10)
Grub screws with a rotating flat tip. The ball can rotate up to 9 Deg. to fasten the object securely.
|
Socket Set Screws - Flat Tip (Relevance 4/10)
Flat tip grub screws
|
Levers | |
Levers - Control Handles - Flat (Relevance 4/10)
Steel Parts: Quality class 5.8. Ball Knob: Black duroplastic FS31 / Surface Finish: Black oxide. Can be used for simpler clamping applications and switching operations. If necessary there must be enough space to turn the handle through an angle of 360°. The star drive hole model is designed to allow turning in steps of 45°.
|
Pulleys | |
Pulleys - Timing - 2.000mm Pitch - GT - STOCK (Relevance 4/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 2.032mm Pitch - MXL (Relevance 4/10)
Timing Pulleys to suit MXL 2.032mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.032mm Pitch - MXL - STOCK (Relevance 4/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 2.073mm Pitch - 40DP (Relevance 4/10)
Timing Pulleys to suit 40DP 2.070mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.500mm Pitch - T2.5 (Relevance 4/10)
Timing Pulleys to suit T Series 2.500mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 2.500mm Pitch - T2.5 - STOCK (Relevance 4/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 3.000mm Pitch - HTD (Relevance 4/10)
Timing Pulleys to suit HTD 3.000mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 3.000mm Pitch - HTD - STOCK (Relevance 4/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 5.000mm Pitch - GT (Relevance 4/10)
|
Pulleys - Timing - 5.000mm Pitch - HTD (Relevance 4/10)
Timing Pulleys to suit HTD 5.000mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 5.000mm Pitch - HTD - STOCK (Relevance 4/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 5.000mm Pitch - T5 (Relevance 4/10)
Timing Pulleys to suit T Series 5.000mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 5.080mm Pitch - XL (Relevance 4/10)
Timing Pulleys to suit XL Series 5.080mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 5.080mm Pitch - XL - STOCK (Relevance 4/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - Timing - 9.525mm Pitch - L (Relevance 4/10)
Timing Pulleys to suit L Series 9.525mm Pitch Timing Belts.
Various materials as shown.
|
Pulleys - Timing - 10.000mm Pitch - T10 - STOCK (Relevance 4/10)
For manufacture of timing pulleys or applications requiring multiple belts from a single drive.
|
Pulleys - U Groove - Plastic (Relevance 4/10)
Acetal Body with Brass Insert.
|
Pulleys - U Groove - Steel (Relevance 4/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Pulleys - Vee - A / 4L - Single Row - Through Bore (Relevance 4/10)
|
Pulleys - Vee - M / 3L - Single Row - Through Bore (Relevance 4/10)
|
Pulleys - Vee - Y / 2L - Single Row - Through Bore (Relevance 4/10)
|
Roller Chain and Sprockets | |
Sprockets - Idler (Relevance 4/10)
Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 4/10)
|
Rollers - Idler - With Aluminium Sleeve (Relevance 4/10)
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
|
Rollers - Idler - With Sintered Bearing (Relevance 4/10)
|
Washers | |
Washers - Flat - Aluminium (Relevance 4/10)
Flat washers.
|
Washers - Flat - Brass - Commercial (Relevance 4/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Brass - Precision (Relevance 4/10)
Precision Tolerances. Laminated brass shim washers.
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 4/10)
Flat Carbon Spring Steel Washers.
|
Washers - Flat - Commercial - All Types (Relevance 4/10)
Includes all materials listed in other commercial washer categories.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Fibre (Relevance 4/10)
Flat fibre washers.
|
Washers - Flat - High Tensile (Relevance 4/10)
ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Mild Steel (Relevance 4/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Nylon (Relevance 4/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - PTFE (Relevance 4/10)
Teflon Washers
|
Washers - Flat - PVC (Relevance 4/10)
Flat washers.
|
Washers - Flat - Precision - All Types (Relevance 4/10)
Includes all materials listed in other precision washer categories.
|
Washers - Flat - Rubber (Relevance 4/10)
|
Washers - Flat - Sintered Bronze - Precision (Relevance 4/10)
Flat washers from oil impregnated sintered bronze
|
Washers - Flat - Stainless Steel - Commercial (Relevance 4/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 4/10)
Precision Tolerances.
|
Washers - Flat - Titanium - CP Grade 1 (Relevance 4/10)
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Adhesives and Sealants | |
Adhesives - General (Relevance 1/10)
Molytec, Loctite, Pacer, Dow Corning, 3M. Includes silicone sealant, gasket adhesive, canopy glue, belt conditioner and electronic tak-pak.
Some items in this category are marked as only available for collection.
|
Retaining Compounds (Relevance 1/10)
Molytec and Loctite. Includes Quickmetal. High and medium retaining for bearings, bushes, gears, pulleys and sprockets.
Some items in this category are marked as only available for collection.
|
Batteries | |
Batteries - Hobby - Lipo (Relevance 1/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom, Hacker. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - NiMH (Relevance 1/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Batteries - Hobby - Nicad (Relevance 1/10)
All types of hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Rings - Tolerance (Relevance 1/10)
Tolerance Rings allow looser tolerances for assembly of parts such as bearings, pulleys and gears.
Allows looser tolerances of components. Ideal for mounting ball bearings. Useful for salvaging worn parts. Permits low cost assembly by eliminating the need for conventional fasteners. Use Torque Transfer figures for gears and pulleys. Non torque transfer figures are for bearing applications.
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Fasteners | |
Nuts - Hexagonal - Brass (Relevance 1/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Pins - Dowel - Extractable (Relevance 1/10)
Hardened and Ground Steel 100 Cr6 to DIN 7979, m6 Dia. Tolerance.
Extractable dowels have a thread tapped in the end to fascilitate removal from blind holes. An air release flat is ground along the full length of the pin. Hardness 55-62 HRC, HV550-650
|
Screws - Machine - Brass - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Nylon - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - PEEK - Pan Head (Relevance 1/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 1/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Titanium CP1 - Countersunk Head (Relevance 1/10)
Flat Head Countersunk. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Socket - Countersunk - Aluminium (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Gearboxes | |
Educational Gearbox Kits (Relevance 1/10)
Basic gearbox kits for prototyping, testing and learning
|
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 1/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 1/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 1/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 1/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 1/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 1/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 1/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - Basic - Hobby Kits (Relevance 1/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Gearmotors - DC - Low Voltage (Relevance 1/10)
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel.
|
Gearmotors - DC - Size 12 (Relevance 1/10)
12mm Gearhead Body Diameter.
|
Gearmotors - DC - Size 20 Low Cost (Relevance 1/10)
20mm Gearhead Body Diameter. Low cost. 70 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 27 Low Cost (Relevance 1/10)
27mm Gearhead Body Diameter. Low cost. 36 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 37/350 Low Cost (Relevance 1/10)
37mm Gearhead Body Diameter. Low cost. 160 RPM Output Speed. One model only. Reversible.
|
Gearmotors - Open Gear (Relevance 1/10)
Perfect for applications where inspection of the gears is important, educational purposes or for visual effects.
|
Solarbotics Gearmotors (Relevance 1/10)
Hobby gearmotors for all types of applications
|
Gears and Gearing | |
Gears - Bevel - 24 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 32 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 48 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 0.8 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 1.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 3 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Cluster - Module 0.5 (Relevance 1/10)
|
Gears - Internal - 24 Pitch (Relevance 1/10)
Various materials including 2024-T4 Aluminum, 303 stainless steel and brass.
|
Gears - Internal - Module 0.5 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 0.8 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 1 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Mitre - 16 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 20 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Unhardened Steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 24 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 32 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 48 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass, carbon steel and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 0.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Brass and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
|
