Categories that include the term: ROLLER
|
Bearings - Needle Roller |  |
Bearings - Needle Roller - Cage Type (Relevance 10/10)
Cage and Rollers.
|
Bearings - Needle Roller - Inner Rings (Relevance 10/10)
Hardened sleeves for needle roller bearings.
|
Bearings - Needle Roller - Machined - With Inner Ring (Relevance 10/10)
|
Bearings - Needle Roller - Machined - Without Inner Ring (Relevance 10/10)
|
Bearings - Needle Roller - Shell Type (Relevance 10/10)
Light Weight. Compact Design.
|
Bearings - Specialty | |
Bearings - Automotive - Tapered Roller (Relevance 10/10)
|
Bearings - One Way - Roller (Relevance 10/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 10/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Bearings and Housings | |
Bearings - Press - Needle Roller - Flange Mounted (Relevance 10/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 10/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Cam Followers - Roller Type - Urethane Covered (Relevance 10/10)
Urethane tyred cam followers for noise reduction, reduced wear and non marking
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 10/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 10/10)
High tensile steel.
|
Chain - Roller - Metal - Simplex (Relevance 10/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 10/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 10/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 10/10)
Includes Miniature Sizes.
|
Chain - Roller - Plastic - Simplex (Relevance 10/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 10/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 10/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 10/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 10/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 10/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 10/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 10/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 10/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 10/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 10/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 10/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 10/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 10/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Sprockets - Idler (Relevance 10/10)
Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Rollers | |
Bearings - Pressure Roller - With Urethane OD (Relevance 10/10)
Bearings with Urethane Tyre on OD for applications requiring frictional movement.
For applications including paper and card dispensing and rolling (eg ATM Machines).
|
Rollers - Idler - Stainless Steel (Relevance 10/10)
|
Rollers - Idler - With Aluminium Sleeve (Relevance 10/10)
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
|
Rollers - Idler - With Sintered Bearing (Relevance 10/10)
|
Rollers - Nylon Tyre (Relevance 10/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Rollers - Steel (Relevance 10/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Rollers - Track - With Inner Race (Relevance 10/10)
|
Rollers - Urethane Feed - With Hub (Relevance 10/10)
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter Sleeve - Aluminium
|
Rollers - Yoke - Cam (Relevance 10/10)
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking
Polycoated shore 80A cast urethane cover
|
RC Car Parts | |
LOSA0051 1/10-Scale Comp Crawler Race Roller Losi Parts (Relevance 8/10)
Bearings and Spare Parts for Remote Control Models
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
|
Hobby Accessories | |
Speed Controllers - Aircraft (Relevance 4/10)
|
Speed Controllers - Car and Buggy (Relevance 4/10)
|
Speed Controllers - Marine (Relevance 4/10)
|
Remote Control Equipment | |
Controllers - Hand (Relevance 4/10)
Transmitters. Includes Spektrum, JR, E-Sky, digital and analogue radio control equipment.
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 3/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 3/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 3/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 3/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 3/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 3/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Fasteners | |
Pins - Dowel - Standard - Hardened Steel (Relevance 3/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 3/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels (Relevance 3/10)
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
|
Dual Vee - Guide Wheels - Studded (Relevance 3/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Dual Vee - Tracks with Mounting Holes (Relevance 3/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 3/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Ladder Chain and Sprockets | |
Chain - Ladder - 6.350mm Pitch (Relevance 3/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
Chain - Ladder - 9.525mm Pitch (Relevance 3/10)
Steel - Brass - Stainless - High Tensile. Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
|
Pulleys | |
Pulleys - Timing - Idler (Relevance 3/10)
Complete with Needle Roller Bearing.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Remote Control Cars | |
Cars - Offroad - Electric - Losi (Relevance 1/10)
Offroad electric cars, trucks, buggies and truggies. 1/8, 1/10, 1/16, 1/18, 1/32 and 1/36 Scale
Brands Include: XXX-4 G+ 4WD, XXX-CR Competition 2WD Buggy Kit, Xxxt-cr, Short Course Truck, 1/18 Dirt Oval Sprint Car Mini Slider, 1/10 Dirt Oval Sprint Car Slider, Mini Desert Buggy Mini Desert Truck, 1/24 4WD Rally Car, Micro Desert Truck, 8IGHT-E 4WD Buggy Race Roller
|
Cars - Offroad - Nitro - Team Losi (Relevance 1/10)
Offroad nitro cars, trucks, buggies and truggies. Includes 1/8 and 1/10 Scale.
Brands Include: T Ten, 810 4WD, 8IGHT 2.0, 8IGHT 2.0 4WD Buggy Race Roller, LST XXL Monster Truck, 8ight 2.0 EU, 8IGHT-T 2.0 and 8IGHT-T 2.0 Race Roller
|
Retaining Rings and Clips | |
Spiral Rings - External - Heavy Duty (Relevance 1/10)
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2
|
Spiral Rings - Internal - Heavy Duty (Relevance 1/10)
Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2
|
|
