Categories that include the terms: ROLLERS and URETHANE and TYRE
|
Rollers |  |
Bearings - Pressure Roller - With Urethane OD (Relevance 10/10)
Bearings with Urethane Tyre on OD for applications requiring frictional movement.
For applications including paper and card dispensing and rolling (eg ATM Machines).
|
Rollers - Urethane Feed - With Hub (Relevance 10/10)
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter Sleeve - Aluminium
|
Cam Followers | |
Cam Followers - Roller Type - Urethane Covered (Relevance 9/10)
Urethane tyred cam followers for noise reduction, reduced wear and non marking
|
Rollers | |
Rollers - Nylon Tyre (Relevance 9/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Cage Type (Relevance 5/10)
Cage and Rollers.
|
Bearings - Needle Roller - Inner Rings (Relevance 5/10)
Hardened sleeves for needle roller bearings.
|
Bearings - Specialty | |
Bearings - One Way - Roller (Relevance 5/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 5/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 5/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Roller Chain and Sprockets | |
Sprockets - Idler (Relevance 5/10)
Complete with Needle Roller or Ball Bearings. 3.75mm to 25.4mm pitch.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Rollers | |
Rollers - Idler - With Aluminium Sleeve (Relevance 5/10)
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
|
Rollers - Yoke - Cam (Relevance 5/10)
Urethane tyred cam yoke rollers for noise reduction, reduced wear and non marking
Polycoated shore 80A cast urethane cover
|
Wheels | |
Wheels and Tyres - Hobby - Car (Relevance 5/10)
1/36, 1/18, 1/10, 1/8 and 1/5 scale wheels and tires (tyres) Brands Proline, Axial, Nanda Venom and Laser
|
Bearings - Needle Roller | |
Bearings - Needle Roller - Machined - With Inner Ring (Relevance 4/10)
|
Bearings - Needle Roller - Machined - Without Inner Ring (Relevance 4/10)
|
Bearings - Needle Roller - Shell Type (Relevance 4/10)
Light Weight. Compact Design.
|
Bearings - Specialty | |
Bearings - Automotive - Tapered Roller (Relevance 4/10)
|
Bearings and Housings | |
Bearings - Press - Needle Roller - Flange Mounted (Relevance 4/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Materials | |
Rod - Round - Urethane (Relevance 4/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 4/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 4/10)
High tensile steel.
|
Chain - Roller - Metal - Simplex (Relevance 4/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 4/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 4/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 4/10)
Includes Miniature Sizes.
|
Chain - Roller - Plastic - Simplex (Relevance 4/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 4/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 4/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 4/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 4/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 4/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 4/10)
|
Rollers - Idler - With Sintered Bearing (Relevance 4/10)
|
Rollers - Steel (Relevance 4/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Rollers - Track - With Inner Race (Relevance 4/10)
|
Wheels | |
Wheels - Hobby - Car - Rockcrawler Rims and Tyres (Relevance 4/10)
Rims and Tires for Axial Rockcrawlers, Losi Night crawler Comp Crawler.
|
Wheels - Trolley - Soft Tyre (Relevance 4/10)
Designed to fit standard supermarket trolley or industrial trolley wheel yokes.
Quiet operation. Non marking. Smooth running.
|
Couplings | |
Couplings - Jaw Type - With Polyurethane Spider (Relevance 3/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Hobby Accessories | |
Speed Controllers - Aircraft (Relevance 3/10)
|
Speed Controllers - Car and Buggy (Relevance 3/10)
|
Speed Controllers - Marine (Relevance 3/10)
|
Materials | |
Rod - Half Round - Styrene (Relevance 3/10)
Styrene (ABS) Plastic
|
Rod - Round - Styrene (Relevance 3/10)
Styrene (ABS) Plastic
|
Sheet - Styrene (Relevance 3/10)
Styrene (ABS) plastic sheet in single sheets and bulk packs
|
Strip - Styrene (Relevance 3/10)
Styrene (ABS) Plastic
|
Tube - Styrene (Relevance 3/10)
Styrene (ABS) Plastic
|
Remote Control Equipment | |
Controllers - Hand (Relevance 3/10)
Transmitters. Includes Spektrum, JR, E-Sky, digital and analogue radio control equipment.
|
Bearings and Housings | |
Bearings - Spyraflo - Flange Mount - Non Aligning (Relevance 1/10)
Low profile flange mounted needle roller and bronze bearings
See links at bottom of web page for more information
|
Bearings - Spyraflo - Flange Mount - Self Aligning (Relevance 1/10)
Low profile self aligning flange mounted needle roller, acetal and bronze bearings
See links at bottom of web page for more information +/- 5% Static Alignment
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 1/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Bearings - Spyraflo - Self Clinching - Non Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Bearings - Spyraflo - Self Clinching - Self Aligning (Relevance 1/10)
Bronze, acetal and needle roller bearings in a special self-clinching housing. Refer technical sheets linked at bottom of tables.
See links at bottom of web page for more information +/- 5% Static Alignment See animation link at bottom of web page Panel material no harder than RB65/RB75 Panel hole to be punched or machined to size A (+0.07/-0.00mm)
|
Fasteners | |
Pins - Dowel - Standard - Hardened Steel (Relevance 1/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 1/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels (Relevance 1/10)
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
|
Dual Vee - Guide Wheels - Studded (Relevance 1/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Dual Vee - Tracks with Mounting Holes (Relevance 1/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 1/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Ladder Chain and Sprockets | |
Chain - Ladder - 6.350mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
Chain - Ladder - 9.525mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
|
Pulleys | |
Pulleys - Timing - Idler (Relevance 1/10)
Complete with Needle Roller Bearing.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Remote Control Cars | |
Cars - Offroad - Electric - Losi (Relevance 1/10)
Offroad electric cars, trucks, buggies and truggies. 1/8, 1/10, 1/16, 1/18, 1/32 and 1/36 Scale
Brands Include: XXX-4 G+ 4WD, XXX-CR Competition 2WD Buggy Kit, Xxxt-cr, Short Course Truck, 1/18 Dirt Oval Sprint Car Mini Slider, 1/10 Dirt Oval Sprint Car Slider, Mini Desert Buggy Mini Desert Truck, 1/24 4WD Rally Car, Micro Desert Truck, 8IGHT-E 4WD Buggy Race Roller
|
Cars - Offroad - Nitro - Team Losi (Relevance 1/10)
Offroad nitro cars, trucks, buggies and truggies. Includes 1/8 and 1/10 Scale.
Brands Include: T Ten, 810 4WD, 8IGHT 2.0, 8IGHT 2.0 4WD Buggy Race Roller, LST XXL Monster Truck, 8ight 2.0 EU, 8IGHT-T 2.0 and 8IGHT-T 2.0 Race Roller
|
Retaining Rings and Clips | |
Spiral Rings - External - Heavy Duty (Relevance 1/10)
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2
|
Spiral Rings - Internal - Heavy Duty (Relevance 1/10)
Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2
|
Wheels | |
Wheels - Drive - Friction (Relevance 1/10)
O-Ring tyre - Acetal body - Brass bore insert.
Brass Bore Insert. Acetal Body. Set Screw Locking. Buna N O-Ring Tyre - 70 Durometer. Bore tolerance +0.025/-0.000.
|
|
