Categories that include the terms: SCREWS and HEX and HEAD and PLASTIC
|
Fasteners |  |
Screws - Hex Head - Plastic (Relevance 10/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Hex Head - Steel (Relevance 10/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Hex Head - Titanium Grade 1 (Relevance 10/10)
Fully threaded hex head screws (DIN933)
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Din 933.
|
Screws - Machine - Nylon - Countersunk Head (Relevance 10/10)
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Large Shallow Head (Relevance 7/10)
UNC - UNF - METRIC - Various Materials.
|
Screws - Machine - Brass - Countersunk Head (Relevance 7/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Nylon (Relevance 7/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - PEEK - Pan Head (Relevance 7/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 7/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 7/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Titanium CP1 - Countersunk Head (Relevance 7/10)
Flat Head Countersunk. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Self Tapping - Countersunk Head (Relevance 7/10)
Countersunk screws length includes head. ie, the full overall length of the screw.
|
Screws - Self Tapping - For Plastics (Relevance 7/10)
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics Be sure to select correct screw for hard or soft plastic threadcutting
|
Screws - Self Tapping - Pan Head (Relevance 7/10)
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
|
Screws - Shoulder - Socket Head (Relevance 7/10)
Includes stainless steel and alloy steel
|
Screws - Socket - Cap - Nylon (Relevance 7/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Socket Set Screws - Acetal Tipped (Relevance 7/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Nylon Tipped (Relevance 7/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 7/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Spacers | |
Spacers - Hex - Threaded - Nylon (Relevance 7/10)
Threaded Hex Spacers.
|
Balls | |
Balls - Acetal (Relevance 4/10)
High intensity strength, rigidity, outstanding resistance to abrasion and most solvents.
Tolerances available on request. Acetal Copolymer. High intensity strength, rigidity, outstanding resistance to abrasion and most solvents. Opaque White. Specific Gravity: 1.4.
|
Balls - Bored - Plastic (Relevance 4/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Nylon (Relevance 4/10)
Resists alkalies, weak acids and most organic solvents.
Tolerances available on request. Nylon (Polyamide 6/6). Resists alkalies, weak acids and most organic solvents. Low water absorption. Unpolished. Specific Gravity: 1.14.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Acetal - with Glass Balls (Relevance 4/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from Ground Glass - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Bearings - Thrust | |
Bearings - Thrust - Plastic - Self Seating (Relevance 4/10)
Tensile strengths shown are Static Axial in Newtons. Easy to install. Good friction wear properties.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 4/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Castors | |
Ball Transfer Units - Screw Stem (Relevance 4/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 4/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Insulators - Screw (Relevance 4/10)
Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.
|
Couplings | |
Couplings - Bellows - Set Screw - Aluminium (Relevance 4/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Fasteners | |
Joints - Clevis - Plastic (Relevance 4/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Nuts - Dome - Nylon (Relevance 4/10)
Natural Nylon.
|
Nuts - Hexagonal - Nylon (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 4/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 4/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 4/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Nylon (Relevance 4/10)
|
Pins - Hammer Drive - Flat Head (Relevance 4/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 4/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Machine - Aluminium (Relevance 4/10)
Metal Thread Screws UNC.
Nuts sold separately - See Fasteners - Nuts.
|
Screws - Machine - Brass (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Titanium CP1 (Relevance 4/10)
Metal Thread Screws - Metric. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Socket - Button - Alloy Steel (Relevance 4/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Aluminium (Relevance 4/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 4/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Zinc Plated (Relevance 4/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Alloy Steel (Relevance 4/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Aluminium (Relevance 4/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Stainless (Relevance 4/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Titanium (Relevance 4/10)
METRIC. CP Grade 1.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Zinc Plated (Relevance 4/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Aluminium (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Thumb - Plain (Relevance 4/10)
Brass, steel, aluminum and stainless and nylon.
|
Screws - Wood - Brass (Relevance 4/10)
Brass wood screws for models
|
Sleeves - Hex Hole (Relevance 4/10)
|
Socket Set Screws - Brass Tipped (Relevance 4/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Cone Point (Relevance 4/10)
Cone point grub screws
|
Socket Set Screws - Cup Point - Standard (Relevance 4/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Socket Set Screws - Dog Point (Relevance 4/10)
Dog point grub screws
|
Socket Set Screws - Flat Ball Tip (Relevance 4/10)
Grub screws with a rotating flat tip. The ball can rotate up to 9 Deg. to fasten the object securely.
|
Socket Set Screws - Flat Tip (Relevance 4/10)
Flat tip grub screws
|
Socket Set Screws - Half Dog Point (Relevance 4/10)
Half Dog Point grub screws
|
Socket Set Screws - Rolling Ball Tip (Relevance 4/10)
Rolling ball tip for locating into a hole
|
Socket Set Screws - Solder Tipped (Relevance 4/10)
Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.
|
Threaded Rod - Allthread - Plastic (Relevance 4/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Plastic with Knurl (Relevance 4/10)
Brass threaded insert Knurled circumference to assist with grip
|
Knobs - Pointer - Aluminium and Plastic (Relevance 4/10)
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
|
Knobs - Star - Female - Plastic (Relevance 4/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Knobs - Star - Male - Plastic (Relevance 4/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Knobs - Thumb - For Cap Screws (Relevance 4/10)
Four Types and four colours to fit onto Socket Head Cap Screws.
To fit Socket Head Cap Screws (Order Separately - See link at base of listing below). Choice of 4 Colours. Choice of 4 styles. Made From Acetal Resin.
|
Knobs - Thumb - With Cap Screw (Relevance 4/10)
Four types and four colours.
Complete with high tensile alloy steel screw. If stainless steel screws required please order cap screws separately and knobs without screw.
|
Hobby Condensed Selection | |
Hobby Gears - Worm and Wheel 40 : 1 Plastic (Relevance 4/10)
Popular Hobby Set
1 start 40 tooth gear.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Nylon with Ertalyte Bearing (Relevance 4/10)
Flanged Ertalyte Bearing in Moulded Nylon 101 Housing.
Self-Lubricating. High Performance. Electrically Insulating.
|
Insert Bearings and Housings | |
Bearings - For Plastic Housings (Relevance 4/10)
Ideal for wet conditions. Includes Acetal and Stainless grades 316 and 440C
Load and speed calculations are for reference only. Testing is recommended.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Pillow Block - Plastic (Relevance 4/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Keys and Keysteel | |
Keys - Gib Head - Steel (Relevance 4/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Keys - Gib Head - Zinc Plated (Relevance 4/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Diameter (Relevance 4/10)
16mm Diameter with pitches 2.5 to 20mm. Machined or unmachined ends. Nuts sold seperately.
Material : Cf53 induction hardened to HRC 62 (=/- 2). Pitch accuracy : <= 0.1mm / 300mm ISO class 7. Nuts sold seperately.
|
Screws - Ball - 16mm Housing - Base Type (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Housing - Flanged (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 4/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Screws - Ball - Economy - Rolled - Nut Only (Relevance 4/10)
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
|
Screws - Ball - Economy - Rolled - Screw Only (Relevance 4/10)
Match with nut. Accuracy T7 50µm/300mm.
Longer lengths available on request (up to 5600mm). Steel Cf53 or Cf60 induction hardened and polished. Running trach hardened to 60 HRC. Profile: Gothic type rolled. Accuracy T7 50µm/300mm.
|
Screws - Ball - Thomson Saginaw (Relevance 4/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nut Flanges for Acme Nuts (Relevance 4/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 4/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Imperial - Acme (Relevance 4/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Acme (Relevance 4/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Materials | |
Rod - Round - Acetal (Relevance 4/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Nylon (Relevance 4/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Plain Bearings | |
Bushes - Plastic - Ertalyte TX (Relevance 4/10)
Self lubricated, high mechanical strength, stiffness and hardness.
Specific Gravity 1.44 g/cm3. Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 76 Mpa. Hardness 94 Rockwell M. High mechanical strength, stiffness and hardness. Self lubricating.
|
Bushes - Plastic - Hobby (Relevance 4/10)
A small selection of popular sizes X-Lube.
See main listings for sizes not shown here. Pricing is highly quantity dependant. Please enquire. Self lubricating - low friction - non-corrosive - light weight - chemical resistance. Molybdenum Disulphide filled Nylon 6.
|
Bushes - Plastic - Iglidur G - Flanged (Relevance 4/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Iglidur G - Unflanged (Relevance 4/10)
General purpose maintenance free dry running.
Specific Gravity 1.45 g/cm3. Operating Temp 220 C short term / 130 C long term. Tensile Strength at 20 deg C 210 Mpa. Hardness 81 Shore D (DIN53505). Tolerances listed are after H7 Pressfit.
|
Bushes - Plastic - Natural Nylon - Unflanged (Relevance 4/10)
Nominal clearance on ID. Nominal oversize on OD for push-fit in housing. Pricing is highly quantity dependant. Please enquire.
|
Bushes - Plastic - X-Lube - Flanged (Relevance 4/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushes - Plastic - X-Lube - Unflanged (Relevance 4/10)
Self lubricating - low friction - non-corrosive - light weight - chemical resistant.
Molybdenum Disulphide filled Nylon 6. Pricing is highly quantity dependant. Please enquire. Note! X-Lube bushes are moulded to nominal tolerances for non critical applications. You will need to machine these bushes to obtain better tolerances and finish.
|
Bushings - Spherical - Plastic (Relevance 4/10)
Ball Material W300. Housing Iglidur G. Maintenance Free. Self lubricating. Compensates for axial loads and misalignment. Corrosion resistant. High vibration dampening capacity.
|
Pulleys | |
Pulleys - U Groove - Plastic (Relevance 4/10)
Acetal Body with Brass Insert.
|
Reels | |
Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 4/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Rod Ends | |
Rod Ends - Plastic (Relevance 4/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Roller Chain and Sprockets | |
Chain - Roller - Plastic - Simplex (Relevance 4/10)
Includes acetal, polyproylene and nylon. Miniature size from 3.1mm up to 12.7mm
Snap together construction - no joining links required.
|
Sprockets - 3.12mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0312 miniature plastic chain
|
Sprockets - 3.75mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0375 miniature plastic or stainless chain
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 4/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Rollers | |
Rollers - Nylon Tyre (Relevance 4/10)
Nylon tyred rollers for cabinet doors, gym equipment etc
|
Shim | |
Shim - Plastic (Relevance 4/10)
Easy to cut - colour coded - plastic shim sheets.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications. Made from sturdy polyester.
|
Spacers | |
Spacers - Hex - Threaded - Brass (Relevance 4/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Stainless Steel (Relevance 4/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Steel (Relevance 4/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Round - Through Bore - Nylon (Relevance 4/10)
Shaft spacers - Nylon
|
Storage | |
Enclosures - Plastic ABS (Relevance 4/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Made with ABS Material, moulded in dark grey. Bosses on internal base allow fixing of PCBs horizontally, or connection of terminals, etc. The lid and base incorporate a tongue and groove sealing system with a neoprene gasket. Lid fixing screws are M4 stainless steel (non-metallic) into threaded brass inserts. Designed to IP65 of IEC529 and NEMS 4 (dust and hoseproof).
|
Parts Boxes - Clear Plastic (Relevance 4/10)
Fischer Plastics clear compartmented parts boxes with flip lids.
Plastic hinged lid. Quality catch to secure contents. Ideal for storing small parts.
|
Parts Boxes - Grey Plastic (Relevance 4/10)
Fischer Plastics grey parts boxes with adjustable dividers and open top.
Open top. Fits most standard shelving. Ideal for storing small parts. Dividers can be removed, added or adjusted. Comes with dividers to make number of compartments shown - but additional dividers can be purchased.
|
Tools | |
Tools - Keys - Hex (Relevance 4/10)
Long and short series allen keys.
Alloy Steel Heat Treated. Short Arm DIN 911. Long Arm ANSI B18.3 1986.
|
Tools - Screw Extractors (Relevance 4/10)
The quick and easy way to remove broken screws, bolts, pipes and studs.
Note! You will also need a drill bit of the correct size for each extractor.
|
Universal Joints | |
Universal Joints - Plastic (Relevance 4/10)
Acetal with or without steel inserts.
|
Universal Joints - Plastic with Brass Inserts - Ondrives (Relevance 4/10)
Cross Piece and Inserts: Brass CZ121 Chromate and passivate finish. Body - Black Acetal Max Speed: 1000 Rpm. Temp. Range: -20 Deg C to +60 Deg C. Backlash Free up to 1000,000,000 Turns.
|
Washers | |
Washers - Disc Spring - Plastic (Relevance 4/10)
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
|
Washers - Flat - Nylon (Relevance 4/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Shoulder - Nylon (Relevance 4/10)
|
Wheels | |
Wheels - Industrial - Plastic (Relevance 4/10)
Wheel loadings include a safety factor of 3. Low noise. Low friction.
|
Worms and Worm Gears | |
Worm Gears - 24 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 2) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 2) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 4/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 2) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 1) - Plastic (Relevance 4/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
|
