Categories that include the terms: SCREWS and HEX and HEAD and TITANIUM and GRADE and 1
|
Fasteners |  |
Screws - Hex Head - Titanium Grade 1 (Relevance 10/10)
Fully threaded hex head screws (DIN933)
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Din 933.
|
Nuts - Hexagonal - Titanium - CP Grade 1 (Relevance 8/10)
METRIC. CP Grade 1.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Machine - Titanium CP1 - Countersunk Head (Relevance 8/10)
Flat Head Countersunk. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Hex Head - Plastic (Relevance 7/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Hex Head - Steel (Relevance 7/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Washers | |
Washers - Flat - Titanium - CP Grade 1 (Relevance 7/10)
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Fasteners | |
Screws - Machine - Titanium CP1 (Relevance 6/10)
Metal Thread Screws - Metric. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Socket - Cap - Titanium (Relevance 5/10)
METRIC. CP Grade 1.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Metric Sizes to DIN912.
|
Balls | |
Balls - Stainless Steel - 316 Grade (Relevance 4/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 4/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Fasteners | |
Screws - Large Shallow Head (Relevance 4/10)
UNC - UNF - METRIC - Various Materials.
|
Screws - Machine - Brass - Countersunk Head (Relevance 4/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Nylon - Countersunk Head (Relevance 4/10)
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - PEEK - Pan Head (Relevance 4/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 4/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Self Tapping - Countersunk Head (Relevance 4/10)
Countersunk screws length includes head. ie, the full overall length of the screw.
|
Screws - Self Tapping - Pan Head (Relevance 4/10)
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
|
Screws - Shoulder - Socket Head (Relevance 4/10)
Includes stainless steel and alloy steel
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Balls | |
Balls - Stainless Steel - 304 Grade (Relevance 3/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 440C Grade (Relevance 3/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Castors | |
Ball Transfer Units - Screw Stem (Relevance 3/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 3/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Insulators - Screw (Relevance 3/10)
Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.
|
Couplings | |
Couplings - Bellows - Set Screw - Aluminium (Relevance 3/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Fasteners | |
Pins - Hammer Drive - Flat Head (Relevance 3/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 3/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Machine - Aluminium (Relevance 3/10)
Metal Thread Screws UNC.
Nuts sold separately - See Fasteners - Nuts.
|
Screws - Machine - Brass (Relevance 3/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Nylon (Relevance 3/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - Stainless Steel (Relevance 3/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 3/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Self Tapping - For Plastics (Relevance 3/10)
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics Be sure to select correct screw for hard or soft plastic threadcutting
|
Screws - Socket - Button - Alloy Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Aluminium (Relevance 3/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Zinc Plated (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Alloy Steel (Relevance 3/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Aluminium (Relevance 3/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Nylon (Relevance 3/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Screws - Socket - Cap - Stainless (Relevance 3/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Zinc Plated (Relevance 3/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Aluminium (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Thumb - Plain (Relevance 3/10)
Brass, steel, aluminum and stainless and nylon.
|
Screws - Wood - Brass (Relevance 3/10)
Brass wood screws for models
|
Sleeves - Hex Hole (Relevance 3/10)
|
Socket Set Screws - Acetal Tipped (Relevance 3/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Brass Tipped (Relevance 3/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Cone Point (Relevance 3/10)
Cone point grub screws
|
Socket Set Screws - Cup Point - Standard (Relevance 3/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Socket Set Screws - Dog Point (Relevance 3/10)
Dog point grub screws
|
Socket Set Screws - Flat Ball Tip (Relevance 3/10)
Grub screws with a rotating flat tip. The ball can rotate up to 9 Deg. to fasten the object securely.
|
Socket Set Screws - Flat Tip (Relevance 3/10)
Flat tip grub screws
|
Socket Set Screws - Half Dog Point (Relevance 3/10)
Half Dog Point grub screws
|
Socket Set Screws - Nylon Tipped (Relevance 3/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Rolling Ball Tip (Relevance 3/10)
Rolling ball tip for locating into a hole
|
Socket Set Screws - Solder Tipped (Relevance 3/10)
Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.
|
Gears and Gearing | |
Gears - Bevel - Module 1 (Relevance 3/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Internal - Module 1 (Relevance 3/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Mitre - Module 1 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - Module 1 (Relevance 3/10)
20 Degree Pressure Angle. Brass, carbon steel, stainless steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - Module 1 (Relevance 3/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 - Stem (Relevance 3/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Stock - Module 1 (Relevance 3/10)
Lengths of spur gear stock for manufacturing gears.
|
Handles and Knobs | |
Knobs - Thumb - For Cap Screws (Relevance 3/10)
Four Types and four colours to fit onto Socket Head Cap Screws.
To fit Socket Head Cap Screws (Order Separately - See link at base of listing below). Choice of 4 Colours. Choice of 4 styles. Made From Acetal Resin.
|
Knobs - Thumb - With Cap Screw (Relevance 3/10)
Four types and four colours.
Complete with high tensile alloy steel screw. If stainless steel screws required please order cap screws separately and knobs without screw.
|
Hobby Condensed Selection | |
Hobby Gears - Worm and Wheel 40 : 1 Plastic (Relevance 3/10)
Popular Hobby Set
1 start 40 tooth gear.
|
Keys and Keysteel | |
Keys - Gib Head - Steel (Relevance 3/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Keys - Gib Head - Zinc Plated (Relevance 3/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Diameter (Relevance 3/10)
16mm Diameter with pitches 2.5 to 20mm. Machined or unmachined ends. Nuts sold seperately.
Material : Cf53 induction hardened to HRC 62 (=/- 2). Pitch accuracy : <= 0.1mm / 300mm ISO class 7. Nuts sold seperately.
|
Screws - Ball - 16mm Housing - Base Type (Relevance 3/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Housing - Flanged (Relevance 3/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Bush Type (Relevance 3/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 3/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Screws - Ball - Economy - Rolled - Nut Only (Relevance 3/10)
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
|
Screws - Ball - Economy - Rolled - Screw Only (Relevance 3/10)
Match with nut. Accuracy T7 50µm/300mm.
Longer lengths available on request (up to 5600mm). Steel Cf53 or Cf60 induction hardened and polished. Running trach hardened to 60 HRC. Profile: Gothic type rolled. Accuracy T7 50µm/300mm.
|
Screws - Ball - Thomson Saginaw (Relevance 3/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nut Flanges for Acme Nuts (Relevance 3/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 3/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 3/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 3/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 3/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Imperial - Acme (Relevance 3/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Acme (Relevance 3/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 3/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Spacers | |
Spacers - Hex - Threaded - Brass (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Nylon (Relevance 3/10)
Threaded Hex Spacers.
|
Spacers - Hex - Threaded - Stainless Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Steel (Relevance 3/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Tools | |
Tools - Keys - Hex (Relevance 3/10)
Long and short series allen keys.
Alloy Steel Heat Treated. Short Arm DIN 911. Long Arm ANSI B18.3 1986.
|
Tools - Screw Extractors (Relevance 3/10)
The quick and easy way to remove broken screws, bolts, pipes and studs.
Note! You will also need a drill bit of the correct size for each extractor.
|
Worms and Worm Gears | |
Worm Gears - 24 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 24 Pitch (Series 1) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 1) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 64 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.5 (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.18 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 1) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.77 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 1) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 48 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 3.35 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 64 Pitch (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 1.78 Degree Lead Angle - 1 Lead. Includes anti-backlash series. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 0.5 (Series 1) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.18 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 1/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 1/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Belts | |
Belts - Timing - 1.000mm Pitch (Relevance 1/10)
Miniature 1mm series timing belts
Pitch (P) - 1.000mm Tooth Height (H) - 0.41mm. Belt Height (W) - 0.97mm Breaking strength is not indicative of working strength.
|
Belts - Vee - 6.4 x 4.1 mm - 2L (Relevance 1/10)
Miniature and small belts. 6.4mm Top Width x 4.1mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 5.5 mm - M/3L (Relevance 1/10)
Miniature and small belts. 10.0mm Top Width x 5.5mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 10.0 x 6.0 mm - Z (Relevance 1/10)
Miniature and small belts. 10.0mm Top Width x 6.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.5 x 9.0 mm - A/4L (Relevance 1/10)
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.7 x 10.0 mm - SPA (Relevance 1/10)
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.3 x 13.0 mm - SPB (Relevance 1/10)
16.3mm Top Width x 13.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 16.5 x 11.0 mm - B/5L (Relevance 1/10)
16.5mm Top Width x 11.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 31.5 x 19.0 mm - D (Relevance 1/10)
31.5mm Top Width x 19.0mm Height.
Sizes are nominal and may vary slightly.
|
Clamping and Locking | |
Hubs - Bolt On (Relevance 1/10)
Aluminium Hub with Set Screws
|
Fasteners | |
Nuts - Hexagonal - Aluminium (Relevance 1/10)
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Hexagonal - Brass (Relevance 1/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon (Relevance 1/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon - Self Tapping (Relevance 1/10)
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 1/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Brass (Relevance 1/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 1/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 1/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 1/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 1/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Pins - Clevis - Stainless Steel 316 (Relevance 1/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Dowel - Standard - Stainless Steel (Relevance 1/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 1/10)
304 and 420 grades DIN1481.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 1/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Gearboxes | |
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 1/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 1/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - DC - Size 12 (Relevance 1/10)
12mm Gearhead Body Diameter.
|
Gears and Gearing | |
Gears - Bevel - Module 1.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Mitre - 16 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
|
