Categories that include the terms: SENSORS and MOTION
|
Electrical |  |
Solarbotics Sensors (Relevance 7/10)
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 7/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 7/10)
For running on shafts fixed at the ends.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed) (Relevance 7/10)
For running on shafts fixed at the ends.
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Carriage Assembly (Relevance 7/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 7/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 7/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Castors | |
Ball Transfer Units - Screw Stem (Relevance 1/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Frelon Lined (Relevance 1/10)
Self aligning. Open or closed. Precision or standard. For rotating and linear motion.
|
Indexing | |
Mechanisms - Geneva (Relevance 1/10)
Geneva device provide precision mechanical intermittent motion.
303 Stainless Steel. Driver may travel in either direction and is reversible. Precision product.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - Thomson Saginaw (Relevance 1/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Drive Systems - Leadscrew | |
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 1/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Rope and Cable | |
Attachments - Thimbles - Synchromesh (Relevance 1/10)
Thimbles provide loop support at higher loads and protect cables from wear when motion is present. Some thimbles may have open or uneven ends.
|
Solarbotics Kits | |
Solarbotics Kit 2 - Photopopper Photovore 4.2b (Relevance 1/10)
A very active solar powered robot. Educational build yourself kits.
Can cover up to a meter (3.3 feet) distance in under 2 minutes. Solar powered, light-sensing directional optics (eyes) and a pair of obstacle avoidance sensors. Directed phototropic or light-seeking behavior - traces outlines around shadows. Everything required is included (high-quality printed circuit board, optics, motors). 12 page instruction manual with over 26 illustrations and images.
|
Solarbotics Kit KHM - Herbie the Mousebot (Relevance 1/10)
Herbie the Mousebot is a very quick, easy-to-build, light-chasing robot kit with functional whisker and tail sensors! Educational build yourself kits.
|
No more categories match your selection
|
