Categories that include the terms: SHAFTING and PRE and DRILLED and RAIL and SUPPORTS
|
Shaft and Shafting |  |
Supports - Flanged Two Bolt (Relevance 6/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 6/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
Couplings | |
Extenders - Shaft (Relevance 4/10)
Miniature and large shaft extenders.
|
Gears and Gearing | |
Gears - Racks - Flexible - Guide Rails (Relevance 4/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Rail (Relevance 4/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Materials | |
Rod - Round - Aluminium (Relevance 4/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Brass (Relevance 4/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Glass Fibre (Relevance 4/10)
High impact light weight glass fibre for modelling.
Glass fibre rod is not smooth.
|
Rod - Round - Sintered Bronze (Relevance 4/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Rod - Round - Stainless Steel (Relevance 4/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Shaft and Shafting | |
Shafting - Ground - Hobby (Relevance 4/10)
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc Not recommended for use with precision steel or stainless steel bearings Some sizes have special features such as serrations or small barbs (noted in description). Unground ends Ideal for axles in robotic applications and educational projects
|
Shafting - Ground - Precision (Relevance 4/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Shafts - Flexible - Coupling Ends - Open (SDP) (Relevance 4/10)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 4/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Splined Shafts and Bushes | |
Splined Bushes - Unflanged (Relevance 4/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Splined Shafts (Relevance 4/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Clamping and Locking | |
Collars - Shaft - Clamp Type (Relevance 3/10)
|
Collars - Shaft - Fairloc (Relevance 3/10)
|
Collars - Shaft - Gripfast (Relevance 3/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Standard (Relevance 3/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Collars - Shaft - With Integral Shim (Relevance 3/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Fasteners | |
Threaded Rod - Allthread - Brass (Relevance 3/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 3/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 3/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Threaded Rod - Aluminium (Relevance 3/10)
UNC and UNF light weight aluminium.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 3/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels (Relevance 3/10)
Vee grooved track roller guide wheels with Abec 5 precision bearings.
Match with correct Track Size.
|
Dual Vee - Guide Wheels - Studded (Relevance 3/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Dual Vee - Tracks with Mounting Holes (Relevance 3/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Dual Vee - Tracks without Mounting Holes (Relevance 3/10)
Vee tracks for vee grooved track roller guide wheels.
Match Track Size with same size Guide Wheel.
|
Linear Motion Bearings | |
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Magnets | |
Magnets - Alcomax - Rectangular Bar (Relevance 3/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 3/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Rod - Sintered (Relevance 3/10)
|
Magnets - Bar (Relevance 3/10)
Great hobby and educational magnets for learning about magnetic attraction
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Materials | |
Bar - H Section - Brass (Relevance 3/10)
|
Bar - I Beam - Brass (Relevance 3/10)
|
Hexagonal Bar - 303 Stainless (Relevance 3/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Brass (Relevance 3/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rectangular Bar - Brass (Relevance 3/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Rod - Half Round - Styrene (Relevance 3/10)
Styrene (ABS) Plastic
|
Rod - Round - Acetal (Relevance 3/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 3/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Carbon Fibre (Relevance 3/10)
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Rod - Round - Nylon (Relevance 3/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - PTFE (Relevance 3/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Polyester PETP (Relevance 3/10)
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Styrene (Relevance 3/10)
Styrene (ABS) Plastic
|
Rod - Round - Urethane (Relevance 3/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Square Bar - 303 Stainless (Relevance 3/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Square Bar - Brass (Relevance 3/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
|
Square Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Rod Ends | |
Rod Ends - Plastic (Relevance 3/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Rod Ends - Steel - Bronze Lined (Relevance 3/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - PTFE Lined (Relevance 3/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Shaft and Shafting | |
Rod - Drill (Relevance 3/10)
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight.
|
Shafts - Flexible - Panel Mount - Cased (Relevance 3/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Open (Relevance 3/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Pinion (Relevance 3/10)
|
Balls | |
Balls - Bored - Plastic (Relevance 1/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Bored - Steel (Relevance 1/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - One Way - Roller (Relevance 1/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze (Relevance 1/10)
Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Press-Fit - Self Aligning (Relevance 1/10)
Needle roller, bronze and acetal bearings in specially designed press fit retainers
See links at bottom of web page for more information +/- 5% Static Alignment Use punch of min dia. J relieved to dia. K x 2mm deep. Refer datasheet for dia. K and J. Link at bottom of web page.
|
Clamping and Locking | |
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Fasteners | |
Joints - Clevis - Plastic (Relevance 1/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Plugs - Pressure (Relevance 1/10)
|
Socket Set Screws - Acetal Tipped (Relevance 1/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Brass Tipped (Relevance 1/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Nylon Tipped (Relevance 1/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Gearboxes | |
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 1/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 1/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 1/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - DC - Low Voltage (Relevance 1/10)
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel.
|
Gears and Gearing | |
Gears - Racks - Flexible (Relevance 1/10)
Blue acetal. Ideal for curved or irregular surfaces. Can fit a bent radius as small as 75mm.
20 Degree Pressure Angle. Resistant to weak acids and alkalis, oil, grease, petrol, alcohol, ketones. Working temperature 100 Deg. C, Intermittent to 149 Deg. C. See optional rack clamps and guide rails. Longer lengths available on special order.
|
Gears - Spur - 16 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 14.5 Degree Pressure Angle. Nylon.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 16 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 64 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.15 (Relevance 1/10)
PCD = No. of Teeth x 0.150mm. 20 Degree Pressure Angle. Brass.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.25 (Relevance 1/10)
PCD = No. of Teeth x 0.250mm. 20 Degree Pressure Angle. Brass and carbon steel.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.4 (Relevance 1/10)
PCD = No. of Teeth x 0.400mm. 20 Degree Pressure Angle. 416 stainless steel, acetal, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.5 (Relevance 1/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.7 (Relevance 1/10)
PCD = No. of Teeth x 0.700mm. 20 Degree Pressure Angle. Acetal.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.75 (Relevance 1/10)
PCD = No. of Teeth x 0.750mm. 20 Degree Pressure Angle. Brass.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.75 - Stem (Relevance 1/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 0.8 (Relevance 1/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 1/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 - Stem (Relevance 1/10)
Gears with integral shafts.
Metallic.
|
Gears - Spur - Module 1.25 (Relevance 1/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.5 (Relevance 1/10)
PCD = No. of Teeth x 1.500mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2 (Relevance 1/10)
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2.5 (Relevance 1/10)
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 3 (Relevance 1/10)
PCD = No. of Teeth x 3.000mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears and Gearing - Matched Sets | |
Gears - Bevel - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets. For 90 degree angle power transfer.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. See Gears - Mitre for 1:1 ratios.
|
Gears - Mitre - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets - 1:1 Ratio. Stainless steel and aluminium.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90 degree angle.
|
Handles and Knobs | |
Knobs - Ball - Knock On - Phenolic (Relevance 1/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Knobs - Oval Tapered - Press On - Phenolic (Relevance 1/10)
Press on knobs hold on securely without threads or set screws
Shaft diameter should be +0.000 / - 0.076 mm for best performance Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside.
|
Knobs - Pointer - 18T Spline Type (Relevance 1/10)
Push on suits 18 tooth splined 6.35mm (1/4 inch) shaft.
|
Knobs - Pointer - Aluminium and Plastic (Relevance 1/10)
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
|
Knobs - Pointer - Arrow Top (Relevance 1/10)
Push on. Suits 6.35mm (1/4 inch) shaft.
|
Knobs - Precision - Knurled (Relevance 1/10)
Set screw and clamp types - Stainless Steel. Also known as Thumb Knobs.
303 Stainless Steel. ID Tolerance +0.013 / -0.000 mm (+0.0005 / - 0.0000 inch).
|
Hinges | |
Hinges - Flexi-Hinge - Precision (Relevance 1/10)
Double and Single Ended - Limited Angle Rotary Applications.
Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature.
|
Hobby Accessories | |
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Hobby Condensed Selection | |
Hobby Washers - Precision Shim (Relevance 1/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Insert Bearings and Housings | |
Bearings - For Pressed Metal Housings (Relevance 1/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 1/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 1/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 1/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Kits | |
Assortment Kits - Various (Relevance 1/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Linear Motion Bearings | |
Bearings - Linear - Ball (Relevance 1/10)
Adjustable and fixed types - open for running on a supported rail and closed for fixed shafts.
Use with hardened precision ground shafting. Shaft tolerance: h6 (Normal Fit), j6 (Close Fit). Housing Tolerance: H7 (Clearance Fit), J7 (Interference Fit). Max Temp: 100 Deg C Intermittent, 80 Deg C continuous.
|
Bearings - Linear - Ball - Thomson Super Smart (Closed) (Relevance 1/10)
For running on shafts fixed at the ends.
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Carriage Assembly (Relevance 1/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 1/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 1/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Magnets | |
Magnets - Ceramic Blocks (Relevance 1/10)
Low cost, light weight, high energy material
Non conductive hard brittle material Performs best at temperatures below 249 Deg C Can be cut with a diamond wheel Difficult to grind and can't be machined or drilled by normal methods Tolerance 0.13mm on all dimensions
|
Materials | |
Balsa Wood - Trailing Edge (Relevance 1/10)
A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only
|
Solarbotics Materials (Relevance 1/10)
Versatile material for building robots because of its ability to glue well with epoxy and superglue.
Can be easily shaped by immersing in hot water and bending to your desired shape while it cools. Can be easily cut, drilled and threaded for screw fasteners. Do not use black Sintra with solar powered robots as it may get soft on hot days.
|
Tube - Round - Aluminium (Relevance 1/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Brass (Relevance 1/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Copper (Relevance 1/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Stainless Steel (Relevance 1/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Motors - Hobby - Robotic - Appliances | |
Motors - DC 12.3X24.4 mm (Relevance 1/10)
M-300C Series 0.5 to 6 VDC - 1820 to 2700 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx. 22 grams.
|
Motors - DC 16.6X32.0 mm (Relevance 1/10)
M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 18.9X18.0X9.5 mm (Relevance 1/10)
M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams.
|
Motors - DC 25.0X21.0 mm (Relevance 1/10)
M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 25.0x20.1X15.1 mm (Relevance 1/10)
M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X23.8 mm (Relevance 1/10)
M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X24.2X18.3 mm (Relevance 1/10)
MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 30.5X24.2 mm (Relevance 1/10)
M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 30.5X24.2X18.3 mm (Relevance 1/10)
MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Mounts and Vibration Control | |
Adjusters - Rigid (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Mild steel bright zinc plated. Screwdriver cross recess in base.
|
Adjusters - Tilt (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25° from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.
|
Pulleys | |
Pulleys - Timing - Idler (Relevance 1/10)
Complete with Needle Roller Bearing.
Can be used directly on shafts with a surface hardnes of RC 58 or higher. Can be run on hardened Inner Rings. See also Drive Tighteners. 12.7mm Bore models can be run directly on the drive tighteners.
|
Remote Control Cars | |
Cars - Onroad - Nitro - Great Vigor (Relevance 1/10)
1/10th onroad nitro cars.
Brands Include: VE Commodore SS Ute, Subaru - Shaft Drive 1/8 scale
|
Retaining Rings and Clips | |
Circlips - External - Grooveless (Relevance 1/10)
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
|
|
