Categories that include the terms: SOLARBOTICS and KIT and 2 and PHOTOPOPPER and PHOTOVORE and 42B
|
Solarbotics Kits |  |
Solarbotics Kit 2 - Photopopper Photovore 4.2b (Relevance 10/10)
A very active solar powered robot. Educational build yourself kits.
Can cover up to a meter (3.3 feet) distance in under 2 minutes. Solar powered, light-sensing directional optics (eyes) and a pair of obstacle avoidance sensors. Directed phototropic or light-seeking behavior - traces outlines around shadows. Everything required is included (high-quality printed circuit board, optics, motors). 12 page instruction manual with over 26 illustrations and images.
|
Solarbotics Kit 5 - SolarSpeeder 1.1 (Relevance 4/10)
The SolarSpeeder 1.1 is a very quick Solaroller. Educational build yourself kits.
Can cover 3 meters (10 feet) in under 40 seconds in direct sunlight. Uses the same updated Solarengine technology found in the PhotoPopper 4.2 Photovore. About 60 mm long when assembled.
|
Solarbotics Kit KHM - Herbie the Mousebot (Relevance 4/10)
Herbie the Mousebot is a very quick, easy-to-build, light-chasing robot kit with functional whisker and tail sensors! Educational build yourself kits.
|
Educational Projects | |
Kits - Mousetrap Powered Vehicles (Relevance 3/10)
These kits are designed to teach kids about physics.
|
Kits - Mousetrap Vehicle Wheels (Relevance 3/10)
Wheels for mousetrap vehicles
|
Kits - Rubber Band Powered (Relevance 3/10)
These kits are designed to teach kids about physics.
|
Electrical | |
Solarbotics Capacitors (Relevance 3/10)
|
Solarbotics Chips - Voltage Detectors (Relevance 3/10)
The Panasonic 1381 series of voltage detectors activate at preset voltage levels.
|
Solarbotics Miscellaneous (Relevance 3/10)
Coils and Trimpot.
|
Solarbotics Parts Bundles (Relevance 3/10)
Bundles of useful parts to assist with bicore experiments.
The large bundle includes a complete BEP board.
|
Solarbotics Sensors (Relevance 3/10)
|
Fasteners | |
Inserts - Thread Repair - Kits (Relevance 3/10)
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 3/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Gearboxes | |
Educational Gearbox Kits (Relevance 3/10)
Basic gearbox kits for prototyping, testing and learning
|
Gearmotors | |
Gearmotors - Basic - Hobby Kits (Relevance 3/10)
These gearmotor kits are of simple mainly plastic design. Great for making simple toys, hobbies or concept testing. Educational series.
|
Solarbotics Gearmotors (Relevance 3/10)
Hobby gearmotors for all types of applications
|
Gears and Gearing | |
Gears - Bevel - Module 2 (Relevance 3/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Mitre - Module 2 (Relevance 3/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - Module 2 (Relevance 3/10)
20 Degree Pressure Angle. Carbon steel, acetal and nylon.
Plastic and metallic.
|
Gears - Spur - Module 2 (Relevance 3/10)
PCD = No. of Teeth x 2.000mm. 20 Degree Pressure Angle. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon. 303 stainless steel, acetal, AISI4135 steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Hobby Accessories | |
Glow Starter Kits (Relevance 3/10)
Starter pack. Fuel Bottel, 4 in 1 spanner, glow starter and charger
|
Propellers - Plane - Nitro - 2 Blade (Relevance 3/10)
|
Spinners - 2 Blade (Relevance 3/10)
Spinners for aircraft propellers
|
Housings with Integral Bearing | |
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 3/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Kits | |
Assortment Kits - Various (Relevance 3/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Materials | |
Solarbotics Materials (Relevance 3/10)
Versatile material for building robots because of its ability to glue well with epoxy and superglue.
Can be easily shaped by immersing in hot water and bending to your desired shape while it cools. Can be easily cut, drilled and threaded for screw fasteners. Do not use black Sintra with solar powered robots as it may get soft on hot days.
|
Model Kit Accessories | |
Model Kit Abrasives (Relevance 3/10)
For a professional finish
|
Model Kit Cement (Relevance 3/10)
Tamiya nd Mr Hobby Glue for plastic model kits
|
Model Kit Knives (Relevance 3/10)
Cutting tools, Excel knife blades and handles, razor saws.
|
Model Kit Masking Tape (Relevance 3/10)
Various sizes
|
Model Kit Paint Brushes (Relevance 3/10)
Paint brushes for finishing plastic model kits
|
Model Kit Paint Thinners (Relevance 3/10)
Thinners for enamel and acrylic paints
|
Model Kit Paints - Acrylic (Relevance 3/10)
Water Based paints for model kits
|
Model Kit Paints - Enamel (Relevance 3/10)
Oil based paints for model kits
|
Model Kit Paints - Textured (Relevance 3/10)
Texture paint for great looking dioramas
|
Model Kit Polishing Compound (Relevance 3/10)
For a professional finish
|
Model Kit Primers and Cleaners (Relevance 3/10)
For surface preparation prior to painting
|
Model Kit Putty (Relevance 3/10)
For a professional finish
|
Model Kit Tools (Relevance 3/10)
Stands, Line Tracing Kit, Applicators, Cleaning Brushes
|
Model Kit Weathering Materials (Relevance 3/10)
For a professional finish
|
Model Kits | |
Model Kits - Cars (Relevance 3/10)
Model kits to build, paint and display. NOT Remote Control.
|
Model Kits - Motorbikes (Relevance 3/10)
Model kits to build, paint and display. NOT Remote Control.
|
Model Kits - Personnel and Equipment (Relevance 3/10)
Model kits to build, paint and display. NOT Remote Control.
|
Model Kits - Planes and Helicopters - Military (Relevance 3/10)
Model kits to build, paint and display. NOT Remote Control.
|
Model Kits - Ships - Boats - Submarines (Relevance 3/10)
Model kits to build, paint and display. NOT Remote Control.
|
Model Kits - Tanks and Armoured Vehicles (Relevance 3/10)
Model kits to build, paint and display. NOT Remote Control.
|
Motors | |
Solarbotics Motors (Relevance 3/10)
|
Remote Control Aircraft | |
Foam Plane Kits Electric - E-flite (Relevance 3/10)
Foam Plane Kits Electric - E-flite
This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands Include: Apprentice
|
Foam Plane Kits Electric - Great Planes (Relevance 3/10)
Outdoor
Brands Include: Flatout Zero
|
Foam Plane Kits Electric - Hobby Zone (Relevance 3/10)
Foam Plane Kits Electric - Hobby Zone
This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands Include: Super Cub LP
|
Foam Plane Kits Electric - Park Zone (Relevance 3/10)
Foam Plane Kits Electric - Park Zone
This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands Include: Spitfire, Messerschmitt, P-51D Mustang, Extra 300, F4F Wildcat, F4U Corsair, T-28D Trojan and Habu
|
Foam Plane Kits Electric - Venom (Relevance 3/10)
Island Hopper, Texan
This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands Include: Texan and Island Hopper
|
Remote Control Boats | |
Boat Kits - Pacific Balsa (Relevance 3/10)
Check the details in Assembly to determine whether the boat is ready to run or requires additional parts.
|
Wheels | |
Solarbotics Wheels (Relevance 3/10)
|
Worms and Worm Gears | |
Worm Gears - 24 Pitch (Series 2) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 32 Pitch (Series 2) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - 48 Pitch (Series 2) - Metallic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
14.5 Degree Pressure Angle - 4.08 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 3/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 24 Pitch (Series 2) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 9.47 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - 32 Pitch (Series 2) - Plastic (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 8.13 Degree Lead Angle - 2 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 0.8 (Series 2) - Plastic Gear and Metallic Worm (Relevance 3/10)
Match with metallic worms Module 0.80 Series 2.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 1 (Series 2) - Plastic Gear and Metallic Worm (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 2 (Series 4) - Plastic Gear and Metallic Worm (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 4.40 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 1/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Specialty | |
Bearings - Ceramic ZrO2 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 1/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Belts | |
Belts - Timing - 2.000mm Pitch - GT - 3mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 6mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.000mm Pitch - GT - 9mm Wide (Relevance 1/10)
GT Series Metric Timing Belts.
Pitch (P) - 2mm. Tooth Height (H) - 0.76mm. Belt Height (W) - 1.52mm. TRUE METRIC is a trademark of Designatronics. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.032mm Pitch - MXL (Relevance 1/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.073mm Pitch - 40DP (Relevance 1/10)
Standard Series Timing Belts 2.072mm or 0.08016 inch pitch.
Pitch (P) - 2.073mm (0.0816 inch). Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.500mm Pitch - T2.5 (Relevance 1/10)
T Series Metric Timing Belts.
Pitch (P) - 2.500mm. Tooth Length (T) - 1.50mm. Tooth Height (H) - 0.70mm. Belt Height (W) - 1.30mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 9.525mm Pitch - L (Relevance 1/10)
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Pitch (P) - 9.525mm (0.200 inch). Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
|
Belts - Vee - 6.4 x 4.1 mm - 2L (Relevance 1/10)
Miniature and small belts. 6.4mm Top Width x 4.1mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.5 x 9.0 mm - A/4L (Relevance 1/10)
12.5mm Top Width x 9.0mm Height.
Sizes are nominal and may vary slightly.
|
Belts - Vee - 12.7 x 10.0 mm - SPA (Relevance 1/10)
12.7mm Top Width x 10.0mm Height.
Sizes are nominal and may vary slightly.
|
Couplings | |
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Fasteners | |
Inserts - Thread Repair (Relevance 1/10)
Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Games | |
Games - Educational (Relevance 1/10)
Crystals, science kits, space race and more
Katamino - Splash Attack - Sputnik - Think Twice Magic Pen - Zimbbos - Zippy Dice
|
Gearboxes | |
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 1/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 1/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 1/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 19.0 x 19.0 x 12.0mm (Relevance 1/10)
Economy Mitre Gear Type. Miniature open gearbox.
Economy hobby type open gearbox Steel mitre gears permanently coupled 1 to 1 ratio
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - DC - Size 12 (Relevance 1/10)
12mm Gearhead Body Diameter.
|
Gearmotors - DC - Size 20 Low Cost (Relevance 1/10)
20mm Gearhead Body Diameter. Low cost. 70 RPM Output Speed. One model only. Reversible.
|
Gearmotors - DC - Size 27 Low Cost (Relevance 1/10)
27mm Gearhead Body Diameter. Low cost. 36 RPM Output Speed. One model only. Reversible.
|
Gears and Gearing | |
Gears - Bevel - 24 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - 32 Pitch (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Bevel - Module 2.5 (Relevance 1/10)
For 90 degree angle power transfer.
20 Degree Pressure Angle. Do not mix gears from different sets. See Gears - Mitre for 1:1 ratios.
|
Gears - Internal - 24 Pitch (Relevance 1/10)
Various materials including 2024-T4 Aluminum, 303 stainless steel and brass.
|
Gears - Mitre - 20 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Unhardened Steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 24 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - 32 Pitch (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Nylon, brass and carbon steel.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 14.5 Degree (Relevance 1/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 24 Pitch - 20 Degree (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 32 Pitch - 14.5 Degree (Relevance 1/10)
14.5 Degree Pressure Angle. Brass, carbon steel and nylon.
Plastic and metallic.
|
Gears - Racks - 72 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 120 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - Module 1.25 (Relevance 1/10)
20 Degree Pressure Angle. Acetal.
Plastic.
|
Gears - Spur - 16 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.588mm (1/16 in.). 20 Degree Pressure Angle. Nylon and acetal.
Plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 14.5 Degree Pressure Angle. Nylon, brass and carbon steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 24 Pitch - Stem (Relevance 1/10)
303 stainless steel.
Metallic.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch - Differential End (Relevance 1/10)
To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel.
Metallic.
|
Gears - Spur - 72 Pitch - Stem (Relevance 1/10)
303 stainless steel.
Metallic.
|
Gears - Spur - Module 0.25 (Relevance 1/10)
PCD = No. of Teeth x 0.250mm. 20 Degree Pressure Angle. Brass and carbon steel.
Metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1.25 (Relevance 1/10)
PCD = No. of Teeth x 1.250mm. 20 Degree Pressure Angle. 303 stainless steel and acetal.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 2.5 (Relevance 1/10)
PCD = No. of Teeth x 2.500mm. 20 Degree Pressure Angle. 303 stainless steel, carbon steel and nylon.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Stock - 20 Pitch (Relevance 1/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears - Spur - Stock - 24 Pitch (Relevance 1/10)
Lengths of spur gear stock for manufacturing gears.
|
Gears and Gearing - Antibacklash | |
Gears - Spur - Antibacklash - 32 Pitch (Relevance 1/10)
Steel - Stainless Steel - Aluminium - 20 Degree Pressure Angle.
|
Hobby Accessories | |
Accessories - Servo Programmer - Digital HFP20 (Relevance 1/10)
Servo programmer-tester for Hitec digital servos
|
Kites | |
Kites - 3D (Relevance 1/10)
|
Kites - Delta - Beginner (Relevance 1/10)
Beginner kites with beautiful pictures
|
Kites - Delta - X (Relevance 1/10)
It's a breeze to launch in winds as light as 4mph and flys well in winds up to 20mph.
|
Kites - Diamond (Relevance 1/10)
Classic Diamond Shape. Great for kids, beginners and family fun.
|
Kites - Parafoil (Relevance 1/10)
Parafoils are reliable and tear resistant. They are strutless so no assembly is required.
|
Kites - Parafoil 63x140 cm (Relevance 1/10)
Parafoils are reliable and tear resistant. They are strutless so no assembly is required.
|
Kites - Singleline Kites (Relevance 1/10)
|
Kites - Skycuulpts (Relevance 1/10)
|
Kites - Sport (Relevance 1/10)
Sport kites are entry level kites with dual-lines which look great and fly well time after time.
|
Kites - Stunt - Beginner (Relevance 1/10)
A great beginner stunt kite.
|
Kites - Stunt - Pro (Relevance 1/10)
A great beginner stunt kite.
|
Kites - Stunt - Vision (Relevance 1/10)
Vision represents a breakthrough in an easy-to-fly stunt kite with excellent handling.
|
Ladder Chain and Sprockets | |
Chain - Ladder - 4.242mm Pitch - Size 21 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 7.264mm Pitch - Size 18 (Relevance 1/10)
Steel - Brass - Stainless - High Tensile.
|
Chain - Ladder - 9.525mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
|
Sprockets - Ladder Chain - 4.242mm Pitch - Size 21 (Relevance 1/10)
With and without Hubs. Plastic and Steel.
|
Sprockets - Ladder Chain - 7.264mm Pitch - Size 18 (Relevance 1/10)
With and without Hubs. Plastic and Steel.
|
Materials | |
Rod - Round - Bronze - LG2 (Standard) (Relevance 1/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 1/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Motors - Hobby - Robotic - Appliances | |
Motors - DC 12.3X24.4 mm (Relevance 1/10)
M-300C Series 0.5 to 6 VDC - 1820 to 2700 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx. 22 grams.
|
Motors - DC 16.6X32.0 mm (Relevance 1/10)
M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 20.0X25.0 mm (Relevance 1/10)
1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts
|
Motors - DC 23.6X25.0 mm (Relevance 1/10)
1.5 to 4.5 VDC - 12,500 RPM unloaded at 4.5 volts
|
Motors - DC 25.0X21.0 mm (Relevance 1/10)
M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 25.0x20.1X15.1 mm (Relevance 1/10)
M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
Motors - DC 26.9X23.8 mm (Relevance 1/10)
M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
|
|
