Categories that include the terms: SPACERS and HEX and THREADED and STAINLESS and STEEL
|
Spacers |  |
Spacers - Hex - Threaded - Stainless Steel (Relevance 10/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Steel (Relevance 10/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Brass (Relevance 9/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Nylon (Relevance 9/10)
Threaded Hex Spacers.
|
Spacers - Round - Through Bore - Stainless Steel (Relevance 9/10)
Shaft spacers - Stainless Steel
|
Fasteners | |
Threaded Rod - Allthread - Stainless Steel (Relevance 8/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Balls | |
Balls - Stainless Steel - 316L Grade (Relevance 6/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 6/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 6/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 6/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Fasteners | |
Nuts - Cap - Stainless Steel (Relevance 6/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 6/10)
Stainless Steel.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 6/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 6/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 6/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Stainless Steel (Relevance 6/10)
304 and 316 Stainless Wing Nuts
|
Screws - Machine - Stainless Steel (Relevance 6/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 6/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Threaded Rod - Allthread - Steel (Relevance 6/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 6/10)
301 S11/S22 Stainless Steel.
|
Snaprings - Internal - Stainless Steel (Relevance 6/10)
301 S11/S22 Stainless Steel.
|
Spacers | |
Spacers - Round - Threaded (Relevance 6/10)
Brass or 303 Stainless Steel
|
Spacers - Round - Through Bore - Steel (Relevance 6/10)
Shaft spacers - Steel
|
Washers | |
Washers - Cup - Stainless Steel (Relevance 6/10)
For countersunk screws.
Stainless Steel cup washers.
|
Balls | |
Balls - Stainless Steel - 304 Grade (Relevance 5/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 5/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Fasteners | |
Pins - Clevis - Stainless Steel 304 (Relevance 5/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 5/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Stainless Steel (Relevance 5/10)
Split pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 5/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 5/10)
304 and 420 grades DIN1481.
|
Screws - Hex Head - Steel (Relevance 5/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 5/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Stainless Steel (Relevance 5/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Materials | |
Rod - Round - Stainless Steel (Relevance 5/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Tube - Round - Stainless Steel (Relevance 5/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 5/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 5/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 5/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 5/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 5/10)
|
Shim | |
Shim and Foil - Stainless Steel (Relevance 5/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Spacers | |
Pillars - Threaded (Relevance 5/10)
Standoffs
|
Washers | |
Washers - Disc Spring - Stainless Steel (Relevance 5/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Stainless Steel - Commercial (Relevance 5/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 5/10)
Precision Tolerances.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 5/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 5/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Balls | |
Balls - Bored - Steel (Relevance 4/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Balls - Chrome Steel (Relevance 4/10)
Hardness: Rockwell C: 60-70.
Tolerances available on request. SAE 52100 Chrome Steel. Hardness: Rockwell C: 60-70. Specific Gravity: 7.833.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 4/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Fasteners | |
Joints - Clevis - Steel (Relevance 4/10)
Made from zinc plated 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). Zinc plate and clear passivated. Pin not included. See also yokes.
|
Nuts - Dome - Steel (Relevance 4/10)
Mild Steel, chrome and zinc plated
|
Nuts - Hexagonal - Nylon Insert - Steel (Relevance 4/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Steel (Relevance 4/10)
UNC - UNF - BA - METRIC. Plain and Zinc Plated.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Screws - Hex Head - Titanium Grade 1 (Relevance 4/10)
Fully threaded hex head screws (DIN933)
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Din 933.
|
Screws - Machine - Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Cap - Alloy Steel (Relevance 4/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Stainless (Relevance 4/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Steel (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Studs - Ball - Threaded (Relevance 4/10)
Zinc Plated Steel DIN 71803 Form C Surface Hardened to 55 HRC (Ball (D1) Only - Thread is Not Hardened)
|
Yoke Ends - Threaded (Relevance 4/10)
Linkage Connectors
Drop forged steel machined to SAE standards Also see clevis joints
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 4/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Plastic with Knurl (Relevance 4/10)
Brass threaded insert Knurled circumference to assist with grip
|
Insert Bearings and Housings | |
Bearings - For Pressed Metal Housings (Relevance 4/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Pillow Block - Pressed Metal (Relevance 4/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Linear Drive Systems - Leadscrew | |
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Materials | |
Hexagonal Bar - 303 Stainless (Relevance 4/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Carbon Steel (Relevance 4/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Square Bar - 303 Stainless (Relevance 4/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Wire - Steel - Spring - Music Wire (Relevance 4/10)
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
|
Plain Bearings | |
Bushings - Spherical - Steel (Relevance 4/10)
Steel
Compensates for axial loads and misalignment.
|
Pulleys | |
Pulleys - U Groove - Steel (Relevance 4/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 4/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - PTFE Lined (Relevance 4/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Duplex (Relevance 4/10)
High tensile steel.
|
Chain - Roller - Metal - Duplex - Links (Relevance 4/10)
High tensile steel.
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 4/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 4/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Rollers | |
Rollers - Steel (Relevance 4/10)
Hardened Steel Rollers as used in Cylindrical and Needle Roller Bearings.
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 4/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Shim | |
Shim and Foil - Steel (Relevance 4/10)
Shim sheet. Cold rolled steel. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Silver Steel | |
Shafting - Ground - Precision (Relevance 4/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Spacers | |
Spacers - Round - Hobby (Relevance 4/10)
Inexpensive nylon spacers for hobby applications
|
Spacers - Round - Through Bore - Aluminium (Relevance 4/10)
Shaft spacers - Aluminium
|
Spacers - Round - Through Bore - Brass (Relevance 4/10)
Shaft spacers - Brass
|
Spacers - Round - Through Bore - Nylon (Relevance 4/10)
Shaft spacers - Nylon
|
Tools | |
Tools - Keys - Hex (Relevance 4/10)
Long and short series allen keys.
Alloy Steel Heat Treated. Short Arm DIN 911. Long Arm ANSI B18.3 1986.
|
Universal Joints | |
Universal Joints - Steel (Relevance 4/10)
Steel - Cast Zinc - Stainless Steel.
|
Washers | |
Washers - Flat - Carbon Spring Steel - Precision (Relevance 4/10)
Flat Carbon Spring Steel Washers.
|
Fasteners | |
Nuts - Hexagonal - Binx (Relevance 3/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Wing - Steel (Relevance 3/10)
Zinc Plated Wing Nuts
|
Pins - Dowel - Standard - Hardened Steel (Relevance 3/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Screws - Hex Head - Plastic (Relevance 3/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Machine - Steel - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Alloy Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Sleeves - Hex Hole (Relevance 3/10)
|
Threaded Rod - Allthread - Brass (Relevance 3/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 3/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Aluminium (Relevance 3/10)
UNC and UNF light weight aluminium.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Phenolic (Relevance 3/10)
Moulded from black or red phenolic resin.
Light Weight. Thermal insulating. Non corrosive.
|
Knobs - Ball - Threaded - Phenolic with Shank (Relevance 3/10)
|
Knobs - Ball - Threaded - Polished Aluminium (Relevance 3/10)
DIN319 Tapped aluminium
Polished with a flash chrome finish
|
Knobs - Ball - Threaded - Polished or Raw Brass (Relevance 3/10)
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes
|
Keys and Keysteel | |
Keys - Gib Head - Steel (Relevance 3/10)
Tapered 3.000 mm per 300 mm (1:100)
|
Keys - Woodruff (Relevance 3/10)
Stainless steel and carbon steel
|
Linear Motion Bearings | |
Bearings - Linear - Ball - Thomson Precision Steel (Closed) (Relevance 3/10)
For running on shafts fixed at the ends.
|
Materials | |
Bungs - Round - Threaded (Relevance 3/10)
|
Bungs - Square - Threaded (Relevance 3/10)
|
Square Bar - Carbon Steel (Relevance 3/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Plain Bearings | |
Bushes - Steel - PTFE Lined - Split (Relevance 3/10)
Similar style to Glacier™ bushes.
|
Reels | |
Reels - Spring Powered - Base Mounted - Steel (Relevance 3/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex (Relevance 3/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Links (Relevance 3/10)
Includes Miniature Sizes.
|
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 3/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 3/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Rope and Cable | |
Attachments - Threaded Plugs (Relevance 3/10)
F and L dimensions are obtained after swaging. Before swaging the fitting is round.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 3/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Spacers - Arbor (Relevance 3/10)
Flat arbor shim washers with keyway groove.
|
Springs | |
Plungers - Spring - Threaded (Relevance 3/10)
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
|
Washers | |
Washers - Disc Spring - Carbon Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Mild Steel (Relevance 3/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Lock - External Tooth - Spring Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Adhesives and Sealants | |
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Batteries | |
Batteries - Hobby - NiMH (Relevance 1/10)
All types of Nickel Metal Hydride (NIMH) hobby battery. Hump, flat, stick packs. E-Sky, Fully Max, Dualsky, RC Revolution, Venom. Some have Tamiya or Deans Connectors.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Flanged (Relevance 1/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 1/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ceramic Hybrid (Relevance 1/10)
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 1/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Housings - Bearing - Pillow Block - Miniature (Relevance 1/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 1/10)
Stainless steel ball type cam followers.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Collars - Shaft - Gripfast (Relevance 1/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - Standard (Relevance 1/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Clutches - Slip - Inline (Relevance 1/10)
Multiplate Design.
Fully adjustable within rating limits. Low stick / slip ratio. Continuous slip within dissipation limit. Zinc plated steel housing with brass plates. Proprietary non-asbestos friction material.
|
Couplings | |
Couplings - Double Disk (Relevance 1/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
Couplings - Double Disk - High Torque (Relevance 1/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
|
