Categories that include the terms: SPRINGS and TORSION and LEFT and HAND and WOUND
|
Springs |  |
Springs - Torsion - Left Hand Wound (Relevance 10/10)
Left Hand Wound. 180 Deg. Deflection. Right hand wound and special springs are available on special order.
|
Springs - Torsion - Right Hand Wound (Relevance 10/10)
Right Hand Wound.
|
Worms and Worm Gears | |
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Left Hand (Relevance 5/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Materials | |
Wire - Steel - Spring - Music Wire (Relevance 4/10)
SAE 1090 Spring Steel.
Shipped in straight lengths on wood backing board.
|
Springs | |
Plungers - Spring - Smooth (Relevance 4/10)
Stainless Steel or Plastic - No Thread.
Body BSD: Pom (Delrin) BSD-SS: W.-Nr 1.4305 (303) Stainless Steel. Sleeve BSD: Thermoplastic BSD-SS: Stainless Steel. Ball: W.-Nr 1.4034 (420) Stainless Steel. Spring: W.-Nr 1.4310 (301) Stainless Steel. Surface Finish BSD: Ball hardened, bright BSD-SS: Bright.
|
Spring Assemblies - Bracket - RINO (Relevance 4/10)
Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.
|
Spring Assemblies - Small Bracket - RINO (Relevance 4/10)
Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
|
Spring Motor Assemblies - Open - RINO (Relevance 4/10)
Budget Assemblies. Average fatigue life of 5000 to 30000 cycles.
Springs : 301 Stainless Steel. Average fatigue life of 5,000 to 30,000 cycles.
|
Spring Motor Assemblies - SDP (Relevance 4/10)
Base Mounted.
Base Mounted. Springs : 301 Stainless Steel.
|
Spring Motors - SDP (Relevance 4/10)
301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.
|
Springs - Compression - Conical (Relevance 4/10)
Conical 302 Stainless steel springs
Solid height lower than a standard compression spring due to the conical shape Ends are closed Starting rate is the same as the kg/mm rate
|
Springs - Compression - Standard (Relevance 4/10)
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
|
Springs - Extension (Relevance 4/10)
Zinc Plated Spring Steel not recommended for applications exceeding 121 Deg C (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 Deg C (500 Deg F). 302 stainless steel is slightly magnetic.
|
Washers | |
Washers - Disc Spring - Plastic (Relevance 4/10)
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 4/10)
Flat Carbon Spring Steel Washers.
|
Fasteners | |
Joints - Clevis - Spring Clips (Relevance 3/10)
Made from 9SMn steel.
Steel 9 SMn 28K (550-700 N/mm2). See also yokes.
|
Reels | |
Reels - Spring Powered - Base Mounted - Plastic Case (Relevance 3/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Reels - Spring Powered - Base Mounted - Steel (Relevance 3/10)
Used in counterbalances, door closers, cable retractors, hose retreivers, tool head returns, cabinets and furniture.
|
Remote Control Equipment | |
Controllers - Hand (Relevance 3/10)
Transmitters. Includes Spektrum, JR, E-Sky, digital and analogue radio control equipment.
|
Springs | |
Plungers - Spring - Threaded (Relevance 3/10)
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
|
Posts - Spring (Relevance 3/10)
|
Springs - Compression - Metre Lengths (Relevance 3/10)
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
|
Springs - Constant Force (Relevance 3/10)
Mounting hole specifications will be supplied on request. Free ID may vary to meet load specification.
|
Springs - Extension - Metre Lengths (Relevance 3/10)
Music wire to Din 17223 Class C. No. 1,1200. Stainless Steel wire to Din 17224 No. 1,4310.
|
Washers | |
Washers - Disc Spring - Carbon Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Disc Spring - Stainless Steel (Relevance 3/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Lock - External Tooth - Spring Steel (Relevance 3/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 3/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Spring (Relevance 3/10)
Wave Washers - All Materials.
|
Worms and Worm Gears | |
Worm Gears - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worm Gears - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 1 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.58 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Worms - Module 2.5 (Series 1) - Plastic and Metallic - Right Hand (Relevance 3/10)
Worms and Gears must be chosen from the same pitch and series to match.
20 Degree Pressure Angle - 3.87 Degree Lead Angle - 1 Lead. A single start worm and gear will provide a ratio equivalent to the number of teeth on the gear. A double start worm and gear will provide a ratio of half the number of teeth on the gear.
|
Clamping and Locking | |
Collars - Shaft - Gripfast (Relevance 1/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Dental Products | |
Tools - Dental Handpiece Repair (Relevance 1/10)
Tools for dental handpiece repair work.
|
Fasteners | |
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Pins - Clevis - Self Locking (Relevance 1/10)
No need for cotter pins
Self locking and reusable with a spring loaded ball lock Plated steel with stainless steel ball
|
Pins - Roll - Plain (Relevance 1/10)
Plain carbon spring steel DIN1481.
|
Pins - Roll - Zinc Plated (Relevance 1/10)
Zinc plated spring steel DIN1481.
|
Handles and Knobs | |
Handles - Soft (Relevance 1/10)
|
Knobs - Ball - Knock On - Phenolic (Relevance 1/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Knobs - Ball - Threaded - Phenolic (Relevance 1/10)
Moulded from black or red phenolic resin.
Light Weight. Thermal insulating. Non corrosive.
|
Knobs - Ball - Threaded - Phenolic with Shank (Relevance 1/10)
|
Knobs - Ball - Threaded - Plastic with Knurl (Relevance 1/10)
Brass threaded insert Knurled circumference to assist with grip
|
Knobs - Ball - Threaded - Polished Aluminium (Relevance 1/10)
DIN319 Tapped aluminium
Polished with a flash chrome finish
|
Knobs - Ball - Threaded - Polished or Raw Brass (Relevance 1/10)
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes
|
Knobs - Cabinet Hardware (Relevance 1/10)
|
Knobs - Knurled - Torque - Female (Relevance 1/10)
Plastic (high grade gloss black phenolic) Knob. Temperature Range: -30°C to +140°C.
|
Knobs - Knurled - Torque - Male (Relevance 1/10)
Plastic (high grade gloss black phenolic) Knob with Steel insert.
|
Knobs - Lever (Relevance 1/10)
Lever knobs with moulded female threads, ideal for direct attachment to operating levers. Plastic (high grade gloss black phenolic) with Steel insert. Temperature Range: -30°C to +140°C. All knobs are fitted with a brass female insert.
|
Knobs - Oval Tapered - Press On - Phenolic (Relevance 1/10)
Press on knobs hold on securely without threads or set screws
Shaft diameter should be +0.000 / - 0.076 mm for best performance Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside.
|
Knobs - Pointer - 18T Spline Type (Relevance 1/10)
Push on suits 18 tooth splined 6.35mm (1/4 inch) shaft.
|
Knobs - Pointer - Aluminium and Plastic (Relevance 1/10)
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
|
Knobs - Pointer - Arrow Top (Relevance 1/10)
Push on. Suits 6.35mm (1/4 inch) shaft.
|
Knobs - Precision - Knurled (Relevance 1/10)
Set screw and clamp types - Stainless Steel. Also known as Thumb Knobs.
303 Stainless Steel. ID Tolerance +0.013 / -0.000 mm (+0.0005 / - 0.0000 inch).
|
Knobs - Star - Female - Plastic (Relevance 1/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Knobs - Star - Male - Plastic (Relevance 1/10)
Plastic (high grade gloss black phenolic) knob with steel insert. Temperature Range: -30°C to +140°C.
|
Knobs - Thumb - Female (Relevance 1/10)
Plastic (high grade gloss black phenolic) with Steel insert. Temperature Range: -30°C to +140°C.
|
Knobs - Thumb - For Cap Screws (Relevance 1/10)
Four Types and four colours to fit onto Socket Head Cap Screws.
To fit Socket Head Cap Screws (Order Separately - See link at base of listing below). Choice of 4 Colours. Choice of 4 styles. Made From Acetal Resin.
|
Knobs - Thumb - With Cap Screw (Relevance 1/10)
Four types and four colours.
Complete with high tensile alloy steel screw. If stainless steel screws required please order cap screws separately and knobs without screw.
|
Knobs - Valve and Handwheels (Relevance 1/10)
|
Knobs - Wing - Female (Relevance 1/10)
Plastic (high grade gloss black phenolic) with Steel Insert. Temperature Range: -30°C to +140°C.
|
Knobs - Wing - Male (Relevance 1/10)
Plastic (high grade gloss black phenolic) with Steel Insert. Temperature Range: -30°C to +140°C.
|
Hinges | |
Hinges - Flexi-Hinge - Precision (Relevance 1/10)
Double and Single Ended - Limited Angle Rotary Applications.
Zero Backlash. Constant Spring Rate. No lubrication required. Self centering on removal of load. -53 to +176 Deg. Celsius operating temperature.
|
Hobby Accessories | |
Accessories - Hobby - General (Relevance 1/10)
General hobby supplies
Velcro Strip - ESC Fans - Heat Shrink - Motor Cooling Stands - Spring Dyno Camera Eye - Tuning Mat - Frequency Keys
|
Kits | |
Assortment Kits - Various (Relevance 1/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Levers | |
Levers - Control Handles - Flat (Relevance 1/10)
Steel Parts: Quality class 5.8. Ball Knob: Black duroplastic FS31 / Surface Finish: Black oxide. Can be used for simpler clamping applications and switching operations. If necessary there must be enough space to turn the handle through an angle of 360°. The star drive hole model is designed to allow turning in steps of 45°.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 1/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Mounts and Vibration Control | |
Mounts - Centre Bolt - Solo Unitised (Relevance 1/10)
Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.
|
Remote Control Aircraft | |
ARF - Balsa - Electric - E-Flite (Relevance 1/10)
Almost Ready to Fly Electric Balsa Planes.
ARF planes do not include motor, speed controller, hand controller, battery, charger etc UNLESS SPECIFIED. Please contact us to confirm inclusions if you are unsure prior to placing your order. This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands include: RV-9, Mini Ultra Stick, Extra 260 3D, Taylorcraft 450, Stearman PT-17, Eratix 3D 25e, Piper L-4 Grasshopper
|
ARF - Balsa - Electric - Hangar 9 (Relevance 1/10)
Almost Ready to Fly Electric Balsa Planes.
ARF planes do not include motor, speed controller, hand controller, battery, charger etc UNLESS SPECIFIED. Please contact us to confirm inclusions if you are unsure prior to placing your order. This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands include: Piper J-3 Cub, Piper Pawnee, Pulse XT, 1/4-Scale J-3 Cub, Sundowner, Taylorcraft
|
ARF - Nitro - Hangar 9 (Relevance 1/10)
Plane Bodies to suit Nitro Engines. Engine Not Included.
These planes do not include engine, hand controller, etc UNLESS SPECIFIED. Please contact us to confirm inclusions if you are unsure prior to placing your order. This product may incur a shipping surcharge. We will contact you prior to processing the order if necessary. Brands Include: PT-19 Control Line 36 Profile, Ultra Stick 40
|
Retaining Rings and Clips | |
Circlips - External - Grooveless (Relevance 1/10)
Includes MIL-R-21248/MS 90707 - Styles M1440 / Ellison GR / Seeger G and GA.
Reusable tapered section rings for grooveless shafts like plastics, tubes or castings. Can be used where adjustable ring placement is desired - like progressively tightening a compression spring.
|
Spiral Rings - External - Heavy Duty (Relevance 1/10)
AHE / WSM / AS3216 / RSN / MIL-R-27426A2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHE, Smalley: WSM, Spirolox and Ramsey: RSN, Aerospace: AS3216, MIL-R-27426A2
|
Spiral Rings - Internal - Heavy Duty (Relevance 1/10)
Includes AHI / WHM / AS3215 / Spirolox RRN / MIL-R-27426B2 - Spring Steel and Stainless Steel.
Heavy duty design for use with NAS669-670 deep grooves in applications like double row and tapered roller bearings. Requires no tools for removal. Equivalent to Associated Spring: AHI, Smalley: WHM, Spirolox and Ramsey: RRN, Aerospace AS3215, MIL-R-27426B2
|
Spiral Rings - Internal - Medium Duty (Relevance 1/10)
Includes AI / WH / AS3217 / RR / MIL-R-27426B1 - Spring Steel and Stainless Steel.
Popular series that will accommodate light and medium bearing series thrust loads. Available in military and aerospace specifications. Equivalent to Associated Spring: AI, Smalley: WH, Spirolox and Ramsey: RR, Aerospace AS3217, MIL-R-27426B1
|
Tools | |
Bits - Insert (Relevance 1/10)
Insert bits for use with hand type screwdriver bit holders
|
Tools - Taps (Relevance 1/10)
High Speed Steel Short Machine and Carbon Steel Straight Flute Taps. starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
High Speed Steel (HSS) Short Machine and Hand Taps. Carbon Steel (CS) Hand taps.
|
Tools - Thread Repair (Relevance 1/10)
Quickly repairs damaged screws
Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.
|
Torches (Relevance 1/10)
Includes hands free and friction recharge types and night vision preservation
|
Washers | |
Washers - Lock - Tabbed - Heavy Duty (Relevance 1/10)
Heavy duty WH / TW Series for bearing locknuts.
Carbon spring steel. Use with NH series locknuts.
|
Washers - Safety (Relevance 1/10)
Spring Steel Hardened Black.
|
|
