Categories that include the terms: STAINLESS and SHAFT
|
Fasteners |  |
Threaded Rod - Allthread - Stainless Steel (Relevance 10/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Materials | |
Hexagonal Bar - 303 Stainless (Relevance 10/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rod - Round - Stainless Steel (Relevance 10/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground.
|
Square Bar - 303 Stainless (Relevance 10/10)
Corrosion resistant 303 grade stainless.
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Clamping and Locking | |
Collars - Shaft - Standard (Relevance 8/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Rod Ends | |
Rod Ends - Steel - Bronze Lined (Relevance 8/10)
Imperial and Metric / Carbon steel and Stainless Steel.
Dimensions not shown are available on request. CFF.SS series are made to DIN 648K and ISO 6126JK.
|
Rod Ends - Steel - PTFE Lined (Relevance 8/10)
Imperial and Metric. Tight fit (Minimal ball clearance) / Carbon steel and Stainless Steel.
Dimensions not shown are available on request.
|
Shaft and Shafting | |
Shafting - Ground - Precision (Relevance 8/10)
Precision ground shafting. Various materials including silver steel, 303 304 316 416 stainless steel, hardened carbon steel, chrome vanadium alloy.
|
Spacers | |
Spacers - Round - Through Bore - Stainless Steel (Relevance 8/10)
Shaft spacers - Stainless Steel
|
Washers | |
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 8/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Balls | |
Balls - Stainless Steel - 304 Grade (Relevance 7/10)
A2 Grade. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs.
Tolerances available on request. Grade 100. Non annealed. Hardness: Rockwell C: 25-39. Specific Gravity: 7.916. Low magnetic permeability. Good corrosion resistance. Excellent for use in handling foodstuffs. Note! Increase in magnetic permeability may occur due to the grinding process and can be relieved by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316 Grade (Relevance 7/10)
A4 Grade. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities.
Tolerances available on request. Grade 100. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972. Low magnetic permeability. Resistant to severe corrosive conditions. Excellent welding and brazing qualities. Note! Increase in magnetic permeability may occur due to the grinding process and can be releived by heating to over 1000 Deg C.
|
Balls - Stainless Steel - 316L Grade (Relevance 7/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Balls - Stainless Steel - 440C Grade (Relevance 7/10)
Hardness: Rockwell C: 55-60.
Tolerances available on request. AISI440C Stainless Steel. Hardness: Rockwell C: 55-60.
|
Bearings | |
Bearings - Ball - 440C Stainless 6000 / 6200 / 6300 Series (Relevance 7/10)
Stainless Steel 440C Grade - Hardened - Precision - Corrosion Resistant.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire.
|
Bearings - Specialty | |
Bearings - Acetal - with 316 Stainless Steel Balls (Relevance 7/10)
Bearings for Extreme Corrosion Resistance - Low Speed - Low Load.
Races made from Acetal - Balls made from 316 Stainless Steel - Cages from Acetal or Nylon. Lubrication - Water Lubrication or can be run dry - Must lubricate over 2500 RPM. Temperature Range - Minus 30 Deg C to 100 Deg C Continuous.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 7/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Clamping and Locking | |
Collars - Shaft - Clamp Type (Relevance 7/10)
|
Collars - Shaft - Fairloc (Relevance 7/10)
|
Collars - Shaft - Gripfast (Relevance 7/10)
Self Locking - Quick Release.
265 kg Load Capacity (600 lbs). ABS Plastic Inner Body and Outer Sleeve. Steel Retention Ring, Balls and Springs.
|
Collars - Shaft - With Integral Shim (Relevance 7/10)
Bore tolerance (+0.003/+0.013). Imperial Collars have undersized tolerances. Metric Collars have oversized tolerances.
|
Couplings | |
Extenders - Shaft (Relevance 7/10)
Miniature and large shaft extenders.
|
Fasteners | |
Nuts - Cap - Stainless Steel (Relevance 7/10)
Stainless Steel. Lower profile than a dome nut.
|
Nuts - Dome - Stainless Steel (Relevance 7/10)
Stainless Steel.
|
Nuts - Hexagonal - Half - Stainless Steel (Relevance 7/10)
UNC - UNF - METRIC
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Stainless Steel (Relevance 7/10)
Nylon Insert for Locking. Nyloc™ and other brands.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Stainless Steel (Relevance 7/10)
UNC - UNF - BA - METRIC - BSW - Course - Fine - Extra Fine.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Wing - Stainless Steel (Relevance 7/10)
304 and 316 Stainless Wing Nuts
|
Pins - Clevis - Stainless Steel 304 (Relevance 7/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Clevis - Stainless Steel 316 (Relevance 7/10)
Match with a suitable R-Clip or Spilt Pin - pin size shown in listings
|
Pins - Cotter - Stainless Steel (Relevance 7/10)
Split pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 7/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Roll - Stainless Steel (Relevance 7/10)
304 and 420 grades DIN1481.
|
Screws - Machine - Stainless Steel (Relevance 7/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 7/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Socket - Button - Stainless Steel (Relevance 7/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Stainless (Relevance 7/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 7/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Threaded Rod - Allthread - Brass (Relevance 7/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 7/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Steel (Relevance 7/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Threaded Rod - Aluminium (Relevance 7/10)
UNC and UNF light weight aluminium.
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 7/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Magnets | |
Magnets - Alcomax - Rectangular Bar (Relevance 7/10)
No keepers
|
Magnets - Alnico - Bar (Relevance 7/10)
Cast Alnico 5 bar
|
Magnets - Alnico - Rod - Sintered (Relevance 7/10)
|
Magnets - Bar (Relevance 7/10)
Great hobby and educational magnets for learning about magnetic attraction
These strong ferrite magnets can be used in hobbies or industrial applications. Non listed sizes can be ordered with minimum quantities often as low as 100 pieces. These are a basic magnet with unfinished edges. The nature of this product is that the edges chip easily so please don't rely on parts having an esthetically pleasing edge finish.
|
Materials | |
Bar - H Section - Brass (Relevance 7/10)
|
Bar - I Beam - Brass (Relevance 7/10)
|
Hexagonal Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small A/F sizes may not be perfectly straight.
|
Hexagonal Bar - Carbon Steel (Relevance 7/10)
Saw Cut Ends. Small A/F sizes may not be perfectly straight.
|
Rectangular Bar - Brass (Relevance 7/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Rod - Half Round - Styrene (Relevance 7/10)
Styrene (ABS) Plastic
|
Rod - Round - Acetal (Relevance 7/10)
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Aluminium (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Brass (Relevance 7/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 7/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Rod - Round - Carbon Fibre (Relevance 7/10)
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish Items marked as Low Grade may have tolerance variations up to 0.2mm
|
Rod - Round - Glass Fibre (Relevance 7/10)
High impact light weight glass fibre for modelling.
Glass fibre rod is not smooth.
|
Rod - Round - Nylon (Relevance 7/10)
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - PTFE (Relevance 7/10)
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Polyester PETP (Relevance 7/10)
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
|
Rod - Round - Sintered Bronze (Relevance 7/10)
Sintered bronze is supplied oversized so it can be machine finished to the dimensions shown.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Oil impregnated porous bronze rod. Smaller diameters may not be supplied straight.
|
Rod - Round - Styrene (Relevance 7/10)
Styrene (ABS) Plastic
|
Rod - Round - Urethane (Relevance 7/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Square Bar - Brass (Relevance 7/10)
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Smaller sizes may not be supplied straight.
|
Square Bar - Carbon Steel (Relevance 7/10)
Saw Cut Ends. Smaller sizes may not be supplied straight.
|
Tube - Round - Stainless Steel (Relevance 7/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Retaining Rings and Clips | |
Snaprings - External - Stainless Steel (Relevance 7/10)
301 S11/S22 Stainless Steel.
|
Snaprings - Internal - Stainless Steel (Relevance 7/10)
301 S11/S22 Stainless Steel.
|
Rod Ends | |
Rod Ends - Plastic (Relevance 7/10)
Thermoplastic Body / L280® Polymer Ball.
Dimensions not shown are available on request.
|
Roller Chain and Sprockets | |
Chain - Roller - Metal - Simplex - Links - Stainless Steel (Relevance 7/10)
Includes Miniature Sizes.
|
Chain - Roller - Metal - Simplex - Stainless Steel (Relevance 7/10)
Includes Miniature Sizes.
|
Sprockets - 3.75mm Pitch - Simplex - Stainless Steel (Relevance 7/10)
With and without Hubs. Miniature 3.75mm Pitch.
Match with 0375 Series Simplex Chain
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 7/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Rollers | |
Rollers - Idler - Stainless Steel (Relevance 7/10)
|
Seals and Sealing | |
Sealing Plugs - Stainless (Relevance 7/10)
The sealing plug is a safe, quick, leakproof and low cost method for sealing cross-drilled holes. It ensures peak performance with a comfortable safety margin even in extreme applications.
Sleeve: Stainless Steel DIN 1.4305, AISI 303 Ball: Bearing Steel, Heat Treated Hardness: HB = 220
|
Shaft and Shafting | |
Rod - Drill (Relevance 7/10)
For punches dies and high strength machine parts. Unhardened - requires heat treatment.
Unfinished ends. Requires heat treating to harden. Small diameters may not be perfectly straight.
|
Shafting - Ground - Hobby (Relevance 7/10)
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc Not recommended for use with precision steel or stainless steel bearings Some sizes have special features such as serrations or small barbs (noted in description). Unground ends Ideal for axles in robotic applications and educational projects
|
Shafts - Flexible - Coupling Ends - Open (SDP) (Relevance 7/10)
Flexible shafting with coupling ends ready to attach to a fixed shaft.
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Cased (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Flexible - Panel Mount - Open (Relevance 7/10)
See PDF file at bottom of internet page for Performance Data.
|
Shafts - Pinion (Relevance 7/10)
|
Supports - Flanged Two Bolt (Relevance 7/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 7/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
Shim | |
Shim and Foil - Stainless Steel (Relevance 7/10)
Shim sheet. Very thin foil to thick sizes. Includes 416, 303 and 316 grades.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Spacers | |
Joints - Tee - Tubing and Rod (Relevance 7/10)
Inexpensive nylon joiners for hobby tubing and rod
|
Spacers - Hex - Threaded - Stainless Steel (Relevance 7/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Splined Shafts and Bushes | |
Splined Bushes - Unflanged (Relevance 7/10)
Match with same size External splined shafts.
Match bushes and shafts by Major Diameter.
|
Splined Shafts (Relevance 7/10)
Match with same size internal splined bushes.
Match bushes and shafts by Major Diameter.
|
Washers | |
Washers - Cup - Stainless Steel (Relevance 7/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Disc Spring - Stainless Steel (Relevance 7/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Stainless Steel - Commercial (Relevance 7/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 7/10)
Precision Tolerances.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 7/10)
Dimensions are nominal and may vary between batches.
|
Clamping and Locking | |
Shaftloc-tm Simple Type M (Relevance 4/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 4/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Balls | |
Balls - Bored - Plastic (Relevance 1/10)
Bored acetal balls as used in plastic rod ends.
Maintenance Free - Self Lubricating. Corrosion Resistant Iglidur W300 material. Suitable for rotating, oscillating and linear movement. Lightweight.
|
Balls - Bored - Steel (Relevance 1/10)
Bored steel balls as used in steel rod ends.
Hardness: 58-64 Rc. Material: SUJ-2.
|
Bearings | |
Bearings - Ball - Single Row - Radial - Flanged (Relevance 1/10)
Stainless and Chrome Steel Bearings with Flanges.
Single Row Radial Ball Bearings. Not all Bearings are readily available. Please enquire. Miniature sizes from 1mm bore to over 50mm bore.
|
Bearings - Ball - Single Row - Radial - Unflanged (Relevance 1/10)
Stainless and Chrome Steel Bearings.
Single Row Radial Ball Bearings. Not all bearings are readily available. Please enquire. Miniature sizes from 0.65 to over 50 mm bore.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - One Way - Roller (Relevance 1/10)
Roller Clutch Bearings rotate in one direction only.
Recommended Shaft Diameter for Clutch Bearings without Inner Ring is +0.000 / -0.005 mm.
|
Bearings and Housings | |
Bearings - Press - Acetal - Flange Mounted (Relevance 1/10)
Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Bearing : PTFE Filled Acetal Self Lubricating / -40 to 150 Deg C. Self lubricating. Use any shaft material with 0.4 um or finer finish.
|
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Press - Sintered Bronze (Relevance 1/10)
Self lubricating. -28 to +95 Deg C. Use any shaft material with 0.8 um or finer finish. Self aligning +/- 5 Degress.
|
Bearings - Press - Sintered Bronze - Flange Mounted (Relevance 1/10)
Porous sintered bronze bearing. -28 to 95 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Use any shaft material with 0.8 um or finer finish.
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 1/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Housings - Bearing - Pillow Block - Miniature (Relevance 1/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 1/10)
Stainless steel ball type cam followers.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clutches and Brakes | |
Clutch Assemblies - Slip - Precision (Relevance 1/10)
Adjustable Torque range 360-3600 g.cm (5-50 oz.in).
303 Stainless Steel. Brake : Oil Impregnated Bronze. Use with hubless gears with 9.525 bore and 3.175 face width.
|
Couplings | |
Couplings - Double Disk (Relevance 1/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
Couplings - Double Disk - High Torque (Relevance 1/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - Slit Type (Relevance 1/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Fasteners | |
Inserts - Keensert (Relevance 1/10)
Stainless Steel 303. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.
|
Inserts - Thread Repair (Relevance 1/10)
Stainless inserts. Replacement Individual Inserts - Require full kit to obtain correct tap. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Inserts - Thread Repair - Assortments (Relevance 1/10)
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Inserts - Thread Repair - Kits (Relevance 1/10)
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
|
Joints - Ball and Socket - Right Angle (Relevance 1/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Joints - Clevis - Plastic (Relevance 1/10)
Use with plastic rod ends - Includes pin and clip. See also yokes.
Comes with clevis pin and retaining clip. Corrosion Resistant, Lightweight. High Tensile Strength (Shown in table as Short Term / Long Term). Vibration Dampening / Noise Dampening. (1) Tensile Strengths shown are Maximum Static axial in Newtons.
|
Locknuts (Relevance 1/10)
Nut Body: Low Carbon Steel. Locking Insert: Stainless Steel Hardness HB 201-269.
|
Nuts - Flange - Serrated (Relevance 1/10)
Stainless Steel.
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Pins - Clevis - Self Locking (Relevance 1/10)
No need for cotter pins
Self locking and reusable with a spring loaded ball lock Plated steel with stainless steel ball
|
Pins - Taper - Imperial - Miniature (Relevance 1/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Miniature sizes. Stainless and Mild Steel.
|
Pins - Taper - Imperial - Standard (Relevance 1/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Screws - Shoulder - Socket Head (Relevance 1/10)
Includes stainless steel and alloy steel
|
Screws - Socket - Countersunk - Steel (Relevance 1/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Thumb - Plain (Relevance 1/10)
Brass, steel, aluminum and stainless and nylon.
|
Socket Set Screws - Acetal Tipped (Relevance 1/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Brass Tipped (Relevance 1/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Cup Point - Standard (Relevance 1/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Socket Set Screws - Nylon Tipped (Relevance 1/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Gearboxes | |
Gearboxes - Right Angle - 30.5 x 30.5 x 18.7mm (Relevance 1/10)
Bevel Gears - 1:1 Ratio. B332 Series. Miniature gearbox.
1:1 Ratio Only / 4mm Shafts. Min Torque 0.5 Ncm. Backlash Approx 2 Degrees. Approx Max Temperature 80 Deg C. Suitable for manual and short term drive application.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 1/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 1/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Gearmotors - DC - Low Voltage (Relevance 1/10)
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Hosuing : Plastic / Shaft : Steel.
|
Gears and Gearing | |
Gears - Internal - 24 Pitch (Relevance 1/10)
Various materials including 2024-T4 Aluminum, 303 stainless steel and brass.
|
Gears - Internal - Module 0.5 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 0.8 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 1 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Mitre - Module 0.6 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 20 Degree (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
|
