Categories that include the terms: STUDS and THREADED and STANDARD
|
Fasteners |  |
Studs - Ball - Threaded (Relevance 9/10)
Zinc Plated Steel DIN 71803 Form C Surface Hardened to 55 HRC (Ball (D1) Only - Thread is Not Hardened)
|
Batteries | |
Batteries - Standard (Relevance 5/10)
The Venom standard non-rechargeable battery range includes AA, AAA, C, D and 9V non-rechargeable.
Bulk packs and single cards
|
Fasteners | |
Pins - Taper - Imperial - Standard (Relevance 5/10)
Imperial Sizes 1:48 Taper (1/4 in. per foot). Standard sizes numbers 0 to 14. Stainless and Mild Steel.
|
Socket Set Screws - Cup Point - Standard (Relevance 5/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Spacers | |
Spacers - Hex - Threaded - Brass (Relevance 5/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Nylon (Relevance 5/10)
Threaded Hex Spacers.
|
Spacers - Hex - Threaded - Stainless Steel (Relevance 5/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Spacers - Hex - Threaded - Steel (Relevance 5/10)
Threaded Hex Spacers. Also known as coupling nuts.
|
Bearings - Clutch | |
Bearings - One Way - Sprag - Standard (Relevance 4/10)
Sprag clutch bearings allow your application to turn one way whilst locking in the opposite direction.
High carbon hardened steel alloy. Always lock out power switch before installing, removing, lubricating or servicing a system that uses Cam Clutch products. When connecting or disconnecting Cam Clutch products, eye protection is required. Wear safety glasses, protective clothing, gloves and safety shoes. Designed for press fit installation.
|
Cam Followers | |
Cam Followers - Miniature - Standard (Relevance 4/10)
Stainless steel ball type cam followers.
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 4/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 4/10)
For conveying materials. From miniature to large.
|
Clamping and Locking | |
Collars - Shaft - Standard (Relevance 4/10)
Includes miniature precision types. Carbon steel, 303 and 316 stainless.
|
Couplings | |
Couplings - Helical - Standard (Relevance 4/10)
0.1 to 16.2 Nm.
Zero backlash. Max. Ang Misalignment 5 Degrees. Max Parallel Offset 0.25mm.
|
Fasteners | |
Pins - Dowel - Standard - Hardened Steel (Relevance 4/10)
Precision Dowel Pins - Various Materials.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Pins - Dowel - Standard - Stainless Steel (Relevance 4/10)
Precision Dowel Pins - Various Corrosion Resistant Grades.
Note! Type 2 pins may be supplied in lieu of type 1 pins.
|
Threaded Rod - Allthread - Brass (Relevance 4/10)
UNC - UNF - METRIC brass.
|
Threaded Rod - Allthread - Plastic (Relevance 4/10)
UNC - UNF - METRIC - Nylon and PVC.
Light Weight. Non Corrosive. Vibration Resistant.
|
Threaded Rod - Allthread - Stainless Steel (Relevance 4/10)
UNC - UNF - METRIC - 303, 304 and 316 grades.
|
Threaded Rod - Allthread - Steel (Relevance 4/10)
UNC - UNF - METRIC - BSW - Includes plain and zinc plated, mild steel and high tensile.
|
Threaded Rod - Aluminium (Relevance 4/10)
UNC and UNF light weight aluminium.
|
Yoke Ends - Threaded (Relevance 4/10)
Linkage Connectors
Drop forged steel machined to SAE standards Also see clevis joints
|
Frame Kits | |
Automat - Frame Kit Threaded Rods (Relevance 4/10)
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Phenolic (Relevance 4/10)
Moulded from black or red phenolic resin.
Light Weight. Thermal insulating. Non corrosive.
|
Knobs - Ball - Threaded - Phenolic with Shank (Relevance 4/10)
|
Knobs - Ball - Threaded - Plastic with Knurl (Relevance 4/10)
Brass threaded insert Knurled circumference to assist with grip
|
Knobs - Ball - Threaded - Polished Aluminium (Relevance 4/10)
DIN319 Tapped aluminium
Polished with a flash chrome finish
|
Knobs - Ball - Threaded - Polished or Raw Brass (Relevance 4/10)
CDA 360 Free Machining Brass
Polished balls are fully finished and suitable for decorative and display purposes
|
Hobby Accessories | |
Propellers - Plane - Electric - Standard (Relevance 4/10)
|
Linear Slides | |
Slides - Linear - Non Recirculating Ball - Standard (Relevance 4/10)
The BSP precision Linear Slide series is a lightweight and compact linear motion rolling guide made of stainless steel formed precisely to be U-shaped table or track rail.
Slides: Stainless Steel End Stop / Retainer: Synthetic Resin. Maximum Speed: 0.5 m/sec (30m/min). Temperature: +100°C (Constant), +120°C (Maximum). Does not incorporate a mechanical stopper. Sensitive to external contaminants.
|
Materials | |
Bungs - Round - Threaded (Relevance 4/10)
|
Bungs - Square - Threaded (Relevance 4/10)
|
Rod - Round - Bronze - LG2 (Standard) (Relevance 4/10)
Leaded Gunmetal Bronze. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Bronze - LG2 (Standard) (Relevance 4/10)
Leaded Gunmetal Bronze tubing. Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Paint | |
Paints - Standard Spray - Tamiya (Relevance 4/10)
Cans of spray paint suitable for painting static models.
Tamiya spray colours provide an impressive finish to static models. When painting figures with a brush, it can be difficult to get paint into creases such as on faces and fabric. Using spray paint is a sure way to get a smooth, even finish. They are also extremely useful for painting large surfaces. Each can contains 100ml of paint, which is enough to fully cover 2 or 3, 1/24 scale sized car bodies. The paint is a synthetic lacquer that cures in a short period of time. Tamiya spray paints are not affected by acrylic or enamel paints. Therefore, following the painting of the entire assembly, details can be added or picked out using enamel and/or acrylic paints. By combining three different paints, the decoration of plastic models will become simpler and more effective.
|
Retaining Rings and Clips | |
Circlips - External - Basic (Standard) (Relevance 4/10)
Imperial and metric DIN471 / N1400 / D1460.
|
Rope and Cable | |
Attachments - Threaded Plugs (Relevance 4/10)
F and L dimensions are obtained after swaging. Before swaging the fitting is round.
|
Spacers | |
Pillars - Threaded (Relevance 4/10)
Standoffs
|
Spacers - Round - Threaded (Relevance 4/10)
Brass or 303 Stainless Steel
|
Springs | |
Plungers - Spring - Threaded (Relevance 4/10)
Items shown with Long-Lok have a dry threadlocking sealant applied to thread.
|
Springs - Compression - Standard (Relevance 4/10)
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
|
Guide Rails - Tracks and Bearings | |
Dual Vee - Guide Wheels - Studded (Relevance 3/10)
Vee grooved track roller guide wheels.
Match with correct Track Size. Note! OD is reference only. Allow up to 1.2 mm larger than listed.
|
Mounts and Vibration Control | |
Dampeners - Double Studded - Silicone (Relevance 3/10)
Damps low frequency vibrations.
Use for compression only.
|
Adhesives and Sealants | |
Epoxies (Relevance 1/10)
ZAP, Molytec, Pacer. 5 and 30 minute. Metal filled and standard.
Some items in this category are marked as only available for collection.
|
Balls | |
Balls - Stainless Steel - 316L Grade (Relevance 1/10)
Easier to machine than standard 316 grade.
316L Stainless Steel has the same properties as 316, except that it has a lower carbon content. It is also easier to machine. Non-magnetic. Resistant to severe corrosive conditions. Hardness: Rockwell C: 25-39. Specific Gravity: 7.972.
|
Bearings | |
Bearings - High Speed Cage (Relevance 1/10)
Bearings with cages for high speed applications, including phenolic, nylon and polyamide.
Bearings in this listing have various types of high speed cages. Speed ratings range from 20 percent to 80 percent increase on standard cage types. Please contact us for a data sheet on the specific size you require.
|
Bearings - Specialty | |
Bearings - Ball - Single Row - Radial - Unflanged - High Precision (Relevance 1/10)
Stainless and Chrome Steel Bearings - Abec 5 and Abec 7.
Single Row Radial Ball Bearings. Miniature sizes from 1mm bore to over 50mm bore. Not all bearings are readily available. Please enquire. True high precision bearings are not recommended for skates or fishing reels. High precision bearings are used in accurately balanced application such as spindles, gyros and medical equipment. If your application is not of a precision nature, standard bearings may be more suitable (and less expensive).
|
Bearings - Ceramic Hybrid (Relevance 1/10)
Steel Races with Si3N4 Ceramic Balls
Bearings with steel races and ceramic balls. For standard bearings, the balls are usually one of the first components to show wear. Ceramic balls are harder than steel and do not wear as easily.
|
Bearings - Ceramic Si3N4 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Belts | |
Belts - Timing - 2.032mm Pitch - MXL (Relevance 1/10)
Standard Series Timing Belts 2.032mm or 0.080 inch pitch.
Pitch (P) - 2.032mm (0.08 inch). Tooth Length (T) - 0.76mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.14mm - Corner Radii ( r ) - 0.13mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 2.073mm Pitch - 40DP (Relevance 1/10)
Standard Series Timing Belts 2.072mm or 0.08016 inch pitch.
Pitch (P) - 2.073mm (0.0816 inch). Tooth Length (T) - 0.60mm. Tooth Height (H) - 0.46mm. Belt Height (W) - 1.20mm - Corner Radii ( r ) - 0.20mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 5.080mm Pitch - XL (Relevance 1/10)
Standard Series Timing Belts 5.080mm or 0.200 inch pitch.
Pitch (P) - 5.080mm (0.200 inch). Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.
|
Belts - Timing - 9.525mm Pitch - L (Relevance 1/10)
Standard Series Timing Belts 9.525mm or 0.375 inch pitch.
Pitch (P) - 9.525mm (0.200 inch). Tooth Length (T) - 3.25mm. Tooth Height (H) - 1.90mm. Belt Height (W) - 3.56mm - Corner Radii ( r ) - 0.50mm. Breaking strength is not indicative of working strength.
|
Books and DVD | |
Books - Engineering (Relevance 1/10)
Machinery handbook contains standards, materials and other general engineering information.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 1/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Couplings | |
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Electrical | |
Power Supplies (Relevance 1/10)
24 V DC.
Standard : 24V DC Output, 110V AC input. Available on special order : 12V DC Output, 220/230V AC input.
|
Fasteners | |
Joints - Ball and Socket - Right Angle (Relevance 1/10)
Steel Type: Zinc Passivated Induction Hardened. Stainless Steel Type: 303 Grade unhardened. Max. Static push/pull loads are valid for both radial and axial loads. Standard Steel type Ball Stud Tensile strength: Rm = 600 N/mm sq (Not applicable to stainless type). Standard Steel type Housing Tensile strength: Rm = 500 N/mm sq (Not applicable to stainless type).
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Hex Head - Titanium Grade 1 (Relevance 1/10)
Fully threaded hex head screws (DIN933)
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Din 933.
|
Screws - Machine - PEEK - Pan Head (Relevance 1/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Yoke Ends - Blank (Relevance 1/10)
Linkage Connectors with blank ends - no hole
Drop forged steel machined to SAE standards Also see clevis joints
|
Gearboxes | |
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 1/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 1/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 1/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 1/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gearmotors | |
Gearmotors - Basic - Hobby - 12.1mm Diameter (Relevance 1/10)
Small light weight geared motors used in toys and small solar applications
NOTE! These gearmotors do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
|
Handles and Knobs | |
Knobs - Ball - Knock On - Phenolic (Relevance 1/10)
Moulded from black phenolic resin.
Light Weight. Thermal insulating. Non corrosive. POK Type have a ribbed insert. Shaft should be 0 to 0.007 mm undersized for best results 712 Type suit standard metric rod
|
Hobby Accessories | |
Accessories - Hobby - Body Clips (Relevance 1/10)
Large and small body clips. Fluoro or standard. Plastic coated or anodised. Range of colours. Bent and straight.
|
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Square - Miniature (Relevance 1/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Housings with Integral Bearing | |
Housings - Bearing - Blocks - Die Cast (Relevance 1/10)
Zinc Die Cast Housings with or without Sintered Bronze Bearings.
Lubricable. With or without standard sintered bronze bearings.
|
Housings - Bearing - Blocks - Frelon Lined (Relevance 1/10)
Self aligning. Open or closed. Precision or standard. For rotating and linear motion.
|
Ladder Chain and Sprockets | |
Chain - Ladder - 6.350mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with standard 6.35mm (1/4) pitch roller chain sprockets
Use with standard 6.35mm (1/4) pitch roller chain sprockets
|
Chain - Ladder - 9.525mm Pitch (Relevance 1/10)
Steel - Brass - Stainless - High Tensile. Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
Use with Standard 9.525mm (3/8) pitch roller chain sprockets.
|
Materials | |
Solarbotics Materials (Relevance 1/10)
Versatile material for building robots because of its ability to glue well with epoxy and superglue.
Can be easily shaped by immersing in hot water and bending to your desired shape while it cools. Can be easily cut, drilled and threaded for screw fasteners. Do not use black Sintra with solar powered robots as it may get soft on hot days.
|
Mounts and Vibration Control | |
Adjusters - Tilt (Relevance 1/10)
Adjustable supports for all kinds of machinery.
Stem: Mild steel bright zinc plated. Base: Polythene or Polypropylene. Angle of Tilt: 25° from perpendicular. Hexagon Nut: 12mm A/F. Standard colour: Black.
|
Mounts - Cylindrical - Female to Blank (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Female to Female (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Blank (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Female (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Male (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Square (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
|
Retaining Rings and Clips | |
Circlips - Internal - Basic (Relevance 1/10)
Imperial and metric DIN471 and 472 / N1300 / Seeger J and JS.
Many sizes can also be ordered in Zinc Plated or Stainless Steel. Tolerances on request. Standard and heavy duty options.
|
Roller Chain and Sprockets | |
Sprockets - 6.35mm Pitch - Simplex - Metal (Relevance 1/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0635 plastic or steel chain (25-1 ASA) American Standard 25-1 - 1/4 inch
|
Sprockets - 6.35mm Pitch - Simplex - Stainless Steel (Relevance 1/10)
With and without Hubs. 25-1 ASA 1/4 Inch
Match with 0635 Series Simplex Chain American Standard 25-1 - 1/4 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Metal (Relevance 1/10)
Match with series 0953047 steel chain (35-1 ASA)
Finish bored and keyed sprockets with black oxide finish. Hub diameters vary to suit bore. American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 4.7mm Width - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953047 plastic or steel chain (35-1 ASA) American Standard 35-1 - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Metal (Relevance 1/10)
Match with series 0953057 steel chain (06B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 06B - 3/8 inch
|
Sprockets - 9.53mm Pitch x 5.7mm Width - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 0953057 steel chain (06B BS) British Standard 06B - 3/8 inch
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Metal (Relevance 1/10)
Match with 12700775 Series Simplex Chain (08B BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 08B - 1/2 inch. With and without hubs.
|
Sprockets - 12.7mm Pitch x 7.75mm Width - Simplex - Plastic (Relevance 1/10)
Nylon - Acetal - With and without bore inserts.
Match with series 12700775 steel chain (08B-1 BS) British Standard 08B - 1/2 inch
|
Sprockets - 15.88mm Pitch x 9.65mm Roller Width - Duplex - Metal (Relevance 1/10)
Match with series 1590094 duplex steel chain (10B-2 BS)
Pilot bored sprockets come with a very small bore that will need to be machined by the customer to suit their shaft size. British Standard 10B - 5/8 inch
|
Sleeving | |
Sleeving - Mesh (Relevance 1/10)
Low cost protection for exterior threaded and cylindrical parts
Elastic snug tight fit on straight, tapered or contoured parts Made from polyethylene Thickness of web approx 1.8mm
|
Springs | |
Springs - Compression - Conical (Relevance 1/10)
Conical 302 Stainless steel springs
Solid height lower than a standard compression spring due to the conical shape Ends are closed Starting rate is the same as the kg/mm rate
|
Storage | |
Enclosures - Plastic ABS (Relevance 1/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Made with ABS Material, moulded in dark grey. Bosses on internal base allow fixing of PCBs horizontally, or connection of terminals, etc. The lid and base incorporate a tongue and groove sealing system with a neoprene gasket. Lid fixing screws are M4 stainless steel (non-metallic) into threaded brass inserts. Designed to IP65 of IEC529 and NEMS 4 (dust and hoseproof).
|
Parts Boxes - Grey Plastic (Relevance 1/10)
Fischer Plastics grey parts boxes with adjustable dividers and open top.
Open top. Fits most standard shelving. Ideal for storing small parts. Dividers can be removed, added or adjusted. Comes with dividers to make number of compartments shown - but additional dividers can be purchased.
|
Tools | |
Tools - Circlip Pliers - External (Relevance 1/10)
External circlip pliers including standard and ratchet type.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.
|
Tools - Circlip Pliers - Internal (Relevance 1/10)
Internal circlip pliers including standard and ratchet type.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.
|
Tools - Circlip Pliers - Reversible (Relevance 1/10)
Reversible circlip pliers for internal and external circlips.
Size ranges shown are for standard circlips. May also suit some non standard sizes outside the range shown. The sizes shown are for reference only. If you are buying a set of pliers to suit one particular job, please enquire as to the suitability of the pliers selected.
|
Tools - Drill Bits (Relevance 1/10)
Micro miniature drill bits starting from 0.32mm up to larger standard sizes. Sutton - PN - Bordo.
Lengths shown are based on standard stock but may vary.
|
Tools - Screw Extractors (Relevance 1/10)
The quick and easy way to remove broken screws, bolts, pipes and studs.
Note! You will also need a drill bit of the correct size for each extractor.
|
Toys | |
Toys - USB (Relevance 1/10)
These toys work off the USB port on standard computers. Great to relieve the tension around the office.
|
Washers | |
Washers - Disk Lock (Relevance 1/10)
Stainless Grade Grade A2 302/316 18-8. Vibration-proof self tightening structural locking device. Maximum Working Temp: +430°C. DISC-LOCK® has outperformed all other types of loose, washered, threaded or pinned systems. in a wide range of high stress, corrosive, and vibration sensitive applications.
|
Wheels | |
Wheels - Trolley - Soft Tyre (Relevance 1/10)
Designed to fit standard supermarket trolley or industrial trolley wheel yokes.
Quiet operation. Non marking. Smooth running.
|
|
