Categories that include the terms: SUSPENSION and UNITS and RUBBER and RECTANGULAR and BOLT
|
Mounts and Vibration Control |  |
Suspension Units - Rubber - Square - Insert Type (Relevance 8/10)
Housing: Steel / Rubber: Black, hardness 70 Shore. Inner square section: Steel tube for mounting plug-in lever arms on one or both sides. All metal parts are paint-finished. Maximum Working Angle: ±30°. Operating Temperature Range: -40°C to +80°C.
|
Castors | |
Ball Transfer Units - Screw Stem (Relevance 5/10)
For conveying materials. From miniature to large.
Measuring equipment. Lightweight coilhander. Guides for small linear motion (eg. photocopier slides). Transfer of material in clean rooms.
|
Castors - Black Rubber (Relevance 4/10)
Black rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Castors - Blue Non Marking Rubber (Relevance 4/10)
Blue non-marking rubber castors including fixed, swivel and brake types. Economical, protects floors, quiet, easy to roll over obstacles
|
Clamping and Locking | |
Hubs - Bolt On (Relevance 4/10)
Aluminium Hub with Set Screws
|
Fasteners | |
Screws - Hex Head - Steel (Relevance 4/10)
UNC - UNF - METRIC - Bolts and Set Screws.
|
Screws - Hex Head - Titanium Grade 1 (Relevance 4/10)
Fully threaded hex head screws (DIN933)
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Din 933.
|
Screws - Machine - Aluminium (Relevance 4/10)
Metal Thread Screws UNC.
Nuts sold separately - See Fasteners - Nuts.
|
Screws - Machine - Brass (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - PEEK - Pan Head (Relevance 4/10)
PEEK is a super-engineering thermoplastic used for its special physical and chemical characteristics. Excellent resistance to chemicals, water, abrasion, shock, fatigue, radiation, heat, etc. PEEK is registered trademark of Vitre™.
Excellent chemical resistance, impenetrable by most chemicals with the exception of concentrated sulphuric acid. Excellent thermal and water resistance; maintains high heat-resistance strength. Excellent abrasion, shock and fatigue resistance. Excellent radiation resistance and electrical properties. Heat-resistant temperature: 180 Degrees Celcius (UL approved temperature). Excellent flame-resistance cleared by UL standard 94V-0. Useful for hot-water pumps, chemical pumps, chemical-resistant applications such as FPD (Flat Panel Display) and semiconductor production equipment/devices, printed circuit board etching devices, metal plating equipment and chemical plants. Use with a nut to compensate for thread moulding pitch errors. When a nut is not used, it is recommended that the overlap of mating screw threads be shorter than 20mm. For further information on the special properties of plastic screws and cautions concerning their use, please contact sales.
|
Screws - Machine - Stainless Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel (Relevance 4/10)
Metal Thread Screws UNC - UNF - BA - METRIC - Zinc Plated and Plain - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Titanium CP1 (Relevance 4/10)
Metal Thread Screws - Metric. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Self Tapping - Countersunk Head (Relevance 4/10)
Countersunk screws length includes head. ie, the full overall length of the screw.
|
Screws - Self Tapping - For Plastics (Relevance 4/10)
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics Be sure to select correct screw for hard or soft plastic threadcutting
|
Screws - Self Tapping - Pan Head (Relevance 4/10)
Type AB Steel Self Tapping Screws.
Length is from the tip of the screw to the base of the head. Ie, does not include the head.
|
Screws - Wood - Brass (Relevance 4/10)
Brass wood screws for models
|
Socket Set Screws - Acetal Tipped (Relevance 4/10)
Acetal tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Brass Tipped (Relevance 4/10)
Brass tipped grub screws. Helps to prevent shaft damage on harder shafts.
|
Socket Set Screws - Cone Point (Relevance 4/10)
Cone point grub screws
|
Socket Set Screws - Cup Point - Standard (Relevance 4/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Socket Set Screws - Dog Point (Relevance 4/10)
Dog point grub screws
|
Socket Set Screws - Flat Ball Tip (Relevance 4/10)
Grub screws with a rotating flat tip. The ball can rotate up to 9 Deg. to fasten the object securely.
|
Socket Set Screws - Flat Tip (Relevance 4/10)
Flat tip grub screws
|
Socket Set Screws - Half Dog Point (Relevance 4/10)
Half Dog Point grub screws
|
Socket Set Screws - Nylon Tipped (Relevance 4/10)
Nylon tipped grub screws. Soft tip compresses into threads to become self locking. Helps to prevent shaft damage.
|
Socket Set Screws - Solder Tipped (Relevance 4/10)
Solder tipped grub screws. Allow fine adjustment and spreads over the contacting surface so as not to mark or deform it.
|
Handles and Knobs | |
Knobs - Thumb - For Cap Screws (Relevance 4/10)
Four Types and four colours to fit onto Socket Head Cap Screws.
To fit Socket Head Cap Screws (Order Separately - See link at base of listing below). Choice of 4 Colours. Choice of 4 styles. Made From Acetal Resin.
|
Knobs - Thumb - With Cap Screw (Relevance 4/10)
Four types and four colours.
Complete with high tensile alloy steel screw. If stainless steel screws required please order cap screws separately and knobs without screw.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Housing - Base Type (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Housing - Flanged (Relevance 4/10)
Use with bush type ball nuts.
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Bush Type (Relevance 4/10)
Antibacklash. Repeatability <0.01mm, accuracy <0.1mm/300mm when used with our screws. Hardened ground and polished Cf53 steel.
|
Screws - Ball - 16mm Nuts - Pillow Block (Relevance 4/10)
Includes ball nut.
Antibacklash. Repeatability 0.01mm, accuracy 0.1mm/300mm when used with our 16mm screws. Hardened ground and polished Cf53 steel to HRC62 +/-2. Balls hardened HRC63 +/- 2.
|
Screws - Ball - Economy - Rolled - Nut Only (Relevance 4/10)
Match with screw. Accuracy T7 50µm/300mm.
Steel 16 MnCr5 or 100Cr6. Size, length of screw and end bearing configurations will affect the resulting loads and speeds. Backlash 0.01 Percent of lead. Accuracy T7 50µm/300mm. Blank sleeve supplied in nut to retain balls. Do not remove without simultaneous assembly to screw.
|
Screws - Ball - Thomson Saginaw (Relevance 4/10)
Offer 90% efficiency converting rotary to linear motion with low coefficient of friction.
When replacing screws, hydraulics or pneumatics, they allow the use of smaller, less expensive drive motors and reduce the need for auxiliary equipment. Offer dependable accuracy and repeatability, Made off high quality alloy steel, hardened to Rockwell 56-60C.
|
Linear Drive Systems - Leadscrew | |
Leadscrew Nut Flanges for Acme Nuts (Relevance 4/10)
Flanges for Acme leadscrew thread nuts imperial
These flanges are screwed onto the outer thread of the red leadscrew nuts This provides a mounting surface to enable location of the leadscrew nut on the surface to be moved
|
Leadscrew Nuts - Imperial - Acme (Relevance 4/10)
Acme Leadscrew Nuts - Use with Acme Leadscrew thread and flanges for mounting
|
Leadscrew Nuts - Metric - Flanged - Plastic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Iglidur W300. Single Start / Right Hand.
|
Leadscrew Nuts - Metric - Hexagonal - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrew Nuts - Metric - Round - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: KSM = Carbon Manganese Steel S300 Pb (11 SMn Pb37) / LRM = Bronze CuSn8P. Carbon Manganese steel can be welded but difficulties may arise with bubbling due to sulphur content. KSM: Manual control control only - low rotational speeds only - for clamping or locking functions - for receiving dead weights. LRM: Manual or powered control - low and medium rotational speeds - for working under load. For power transmission and continuous use always use bronze nuts not steel.
|
Leadscrew Nuts - Metric - Square - Metallic (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew thread listed in separate category.
Material: Carbon Manganese Steel S300 Pb (11 SMn Pb37). If welding, difficulties may arise with bubbling due to sulphur content. To be used with screws:- LFM, LSM, LRH, LSRH (Single Start). Manual control - Low rotation speeds - For clamping or locking functions - For receiving dead weights. For power transmission and continuous use, always use bronze nuts, never steel. Nuts and screws should always be lubricated with grease or oil.
|
Leadscrews - Imperial - Acme (Relevance 4/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Acme (Relevance 4/10)
Acme Leadscrew Thread - Use with Acme Supernuts
|
Leadscrews - Metric - Rolled Thread - Carbon Steel (Relevance 4/10)
Trapezoidal thread design. Use with metric leadscrew nuts listed in separate category.
Carbon Steel C35 For power transmission and continuous use always use bronze nuts - never steel. Nuts and screws should always be lubricated with grease or oil. Steel nuts with steel screws should only be used for hand motion. Efficiency Guide 20 percent with lubrication for single start.
|
Magnets | |
Magnets - Rubber and Vinyl (Relevance 4/10)
Magnetic Vinyl Sheets and Magnetic Rubber Strip
|
Materials | |
Rectangular Bar - Brass (Relevance 4/10)
Thin and thick brass strip and rectangular profiles
Saw Cut Ends. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries. Small sizes may not be perfectly straight.
|
Tube - Rectangular - Brass (Relevance 4/10)
Rectangular hollow tubing.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Mounts and Vibration Control | |
Mounts - Centre Bolt - Solo Unitised (Relevance 4/10)
Calculate static load and select a mount of equal or greater capacity. For dynamic loads of 3 x static load select the next larger size. Lubricate mount and socket with water or rubber lubricant. Insert into socket and hand rotate with axial force. Outer Body : Natural Rubber / Spacer : Rolled Tubular Steel.
|
Seals and Sealing | |
Oil Seals - Nitrile Rubber (Relevance 4/10)
DIN 3760 - General purpose grease and oil sealing.
Operating Temp. Range: -30°C to +90°C. The rubber elastomer outer covering tolerates thermal expansion as well as roughness in the housing bore. Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.
|
Shaft and Shafting | |
Supports - Flanged Two Bolt (Relevance 4/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 4/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
Tools | |
Tools - Screw Extractors (Relevance 4/10)
The quick and easy way to remove broken screws, bolts, pipes and studs.
Note! You will also need a drill bit of the correct size for each extractor.
|
Castors | |
Ball Transfer Units - Base Mount - Standard Duty (Relevance 3/10)
For conveying materials.
|
Ball Transfer Units - Flange Mount - Standard Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Ball Transfer Units - Heavy Duty (Relevance 3/10)
For conveying materials. From miniature to large.
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 3/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Insulators - Screw (Relevance 3/10)
Nonconductive. Noncorrosive. Lightweight. Self-sealing. Self-locking.
|
Couplings | |
Couplings - Bellows - Set Screw - Aluminium (Relevance 3/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Couplings - Jaw Type - With Rubber Spider (Relevance 3/10)
Max 3600 RPM. 0.39 to 16.27 Nm.
Angular Offset = 1 Deg. Max. Parallel Offset = 0.381mm Max. Max Recommended Speed 3600 RPM.
|
Educational Projects | |
Kits - Rubber Band Powered (Relevance 3/10)
These kits are designed to teach kids about physics.
|
Fasteners | |
Screws - Hex Head - Plastic (Relevance 3/10)
UNC - UNF - METRIC - Nylon and PVC.
|
Screws - Large Shallow Head (Relevance 3/10)
UNC - UNF - METRIC - Various Materials.
|
Screws - Machine - Brass - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Nylon (Relevance 3/10)
UNC / UNF / Metric. Pan head, cheese head, binder head.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - Nylon - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC and UNF.
Non Conductive. Non Corrosive. Non Magnetic. Lightweight. Vibration Resistant.
|
Screws - Machine - Stainless Steel - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Steel - Countersunk Head (Relevance 3/10)
Flat Head Countersunk UNC - UNF - BA - METRIC - Plain and Zinc Plated - Various Head Types.
Nuts sold seperately - See Nuts.
|
Screws - Machine - Titanium CP1 - Countersunk Head (Relevance 3/10)
Flat Head Countersunk. CP Grade 1 Titanium.
Nuts sold seperately - See Nuts. CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250.
|
Screws - Shoulder - Socket Head (Relevance 3/10)
Includes stainless steel and alloy steel
|
Screws - Socket - Button - Alloy Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Aluminium (Relevance 3/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Stainless Steel (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Button - Zinc Plated (Relevance 3/10)
UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Alloy Steel (Relevance 3/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Aluminium (Relevance 3/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Nylon (Relevance 3/10)
UNC - UNF - METRIC - Non Conductive - Non Magnetic.
|
Screws - Socket - Cap - Stainless (Relevance 3/10)
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Titanium (Relevance 3/10)
METRIC. CP Grade 1.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Metric Sizes to DIN912.
|
Screws - Socket - Cap - Zinc Plated (Relevance 3/10)
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Aluminium (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Stainless Steel (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Socket - Countersunk - Steel (Relevance 3/10)
Flat Head Countersunk UNC - UNF - METRIC - Alloy Steel - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Screws - Thumb - Plain (Relevance 3/10)
Brass, steel, aluminum and stainless and nylon.
|
Socket Set Screws - Rolling Ball Tip (Relevance 3/10)
Rolling ball tip for locating into a hole
|
Housings with Integral Bearing | |
Housings - Bearing - Flanged - 2 Bolt Hole - W300 (Relevance 3/10)
With integral self aligning plain bearing.
Housing: Igumid G. Ball: Highly wear resistant Iglidur W300.
|
Insert Bearings and Housings | |
Housings - Bearing - Flanged - 2 Bolt Hole - Cast Iron (Relevance 3/10)
Lubrication Groove. Bearings sold separately. Larger sizes available on request. Use with steel bearing inserts for cast iron housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Plastic (Relevance 3/10)
Load and speed capability depend on the bearing used. Use with steel bearing inserts for plastic housings.
|
Housings - Bearing - Flanged - 2 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Housings - Bearing - Flanged - 3 Bolt Hole - Pressed Metal (Relevance 3/10)
Bearings sold separately. Use with steel bearing inserts for pressed metal housings. Larger sizes available on request.
|
Keys and Keysteel | |
Keys - Keysteel Lengths - Rectangular (Relevance 3/10)
Manufactured slightly oversize to prevent machine backlash. Zinc plating may be silver or gold in colour.
|
Linear Drive Systems - Ballscrew | |
Screws - Ball - 16mm Diameter (Relevance 3/10)
16mm Diameter with pitches 2.5 to 20mm. Machined or unmachined ends. Nuts sold seperately.
Material : Cf53 induction hardened to HRC 62 (=/- 2). Pitch accuracy : <= 0.1mm / 300mm ISO class 7. Nuts sold seperately.
|
Screws - Ball - Economy - Rolled - Screw Only (Relevance 3/10)
Match with nut. Accuracy T7 50µm/300mm.
Longer lengths available on request (up to 5600mm). Steel Cf53 or Cf60 induction hardened and polished. Running trach hardened to 60 HRC. Profile: Gothic type rolled. Accuracy T7 50µm/300mm.
|
Magnets | |
Magnets - Alcomax - Rectangular Bar (Relevance 3/10)
No keepers
|
Materials | |
Plates - Bronze - Sintered - Rectangular (Relevance 3/10)
SAE 841 Powdered metal bronze bearing plates.
Width and length are oversized and will finish to the dimensions shown. Thickness +/- 0.127mm.
|
Tube - Rectangular - Carbon Fibre (Relevance 3/10)
High impact light weight carbon fibre hollow tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish
|
Seals and Sealing | |
O-Rings - Nitrile Rubber (Relevance 3/10)
General purpose.
Temperature Range: -30°C to +90°C. Nitrile: Excellent resistance to mineral oil based fluids, hydrocarbon fuels, greases and water. Not suitable for aromatic hydrocarbons, chlorinated hydrocarbons, brake fluid and some fire resistant hydraulic fluids.
|
O-Rings - Silicone Rubber (Relevance 3/10)
High thermal resistance and cold flexibility.
Temperature Range: -70°C to +200°C. Good dialectric properties and resistance to ozone and oxygen attack. Retains flexibility at high and low temperatures. Poor strength and tear resistance. Poor resistance to oils, fuels, concentrated acids and alkalis, water and steam.
|
Shim | |
Shims - Rubber (Relevance 3/10)
Handy non marring soft spacer shims in a wedge shape
Level and stabilise appliances, desks, tables, filing cabinets, machinery Stackable. Vibration cushioning. Ribs ensure that wedges grab tight and stay in place Black ridid wedges can support up to 2000 lbs White flexible wedges can be trimmed with a utility knife
|
Toys | |
Toys - Planes - Rubber Band and Throwing (Relevance 3/10)
Inexpensive foam gliders, planes and Twirly Propellers
|
Universal Joints | |
Covers - Universal Joint - Elasticate Rubber (Relevance 3/10)
For Single and Double Universal Joints.
-27 Deg C to 70 Deg C temp range (constant). -32 Deg C to 120 Deg C temp range (intermittent).
|
Washers | |
Washers - Flat - Rubber (Relevance 3/10)
|
Adhesives and Sealants | |
Super Bonders (Relevance 1/10)
Mercury, ZAP, Molytec, Loctite, Pacer, Pro Seal. Cyanoacrylate adhesives for quick bonding. Products for foam Kicker, wood, metals, rubber and plastics.
Some items in this category are marked as only available for collection.
|
Bearings - Thrust | |
Lazy Susan Bearings (Relevance 1/10)
One unit construction for maximum stability and quiet running.
Centre opening allows for a centre post if required.
|
Cam Followers | |
Cam Followers - Roller Type - Stainless Steel (Relevance 1/10)
Stainless steel roller type cam followers.
Stainless Steel similar to 440C. Seals: Synthetic rubber seals. Shields: Stainless Steel shields. Screwdriver slot for mounting. Stud designed to fit H7 housing.
|
Clamping and Locking | |
Reducers - Bore (Relevance 1/10)
Inch to Metric / Inch to Inch / Metric to Metric.
S = Recommended set screw positions. C = Recommended position for single set screw fastening. T = Recommended position for tangential screw in clamp hub.
|
Shaftloc-tm Simple Type M (Relevance 1/10)
Simple effective way to lock components onto shafts.
Passivated 416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened Precision, dynamically balanced and suitable for high speed applications. Diameters A and B concentric within 0.013 T.I.R. Tightening the nut causes slotted sleeve to contract, gripping the shaft and clamping the component to the sleeve.
|
Shaftloc-tm Sleeves - Single Ended (Relevance 1/10)
Simple effective way to lock components onto shafts.
416 Stainless Steel Simple two part screw together system locks parts securely to shaft. Asymetric thread geometry produces a large radial clamping force when the nut is tightened
|
Fasteners | |
Inserts - Expansion (Relevance 1/10)
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability but where maximum strength is required other inserts shown in this catalogue should be preferred.
|
Inserts - Keensert (Relevance 1/10)
Stainless Steel 303. Maximum strength and reliability. Positive mechanical lock against rotation:. The insert kees are driven down into the tapped threads of the parent material during installation to securely lock the insert against rotation. Inserts with internal thread lock are designed to securely lock a bolt when it is entered into the insert only a few turns.
|
Nuts - Aerotight (Relevance 1/10)
Aerotight is a Registered Trademark and can only be applied to goods manufactured by the Premier Screw and Repetition Company Limited. Any company infringing the registered trade mark may be liable to legal proceedings. Aerotight nuts should not be used on damaged or interrupted threads. When assembled on the screw at least two threads should protrude through the Aerotight nut. Advantages: Will not work loose. No other locking device needed.
|
Nuts - Hexagonal - Binx (Relevance 1/10)
Manufactured from A2 302/304 grade stainless steel. The standard Binx's entire locking action is contained within the nut body which is no thicker than a standard full nut. The ingenious design incorporates two opposing cantilever type springs which lock onto the bolt with inward and downward pressure. May be removed and placed repeatedly with minimum thread wear.
|
Nuts - Hexagonal - Brass (Relevance 1/10)
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
|
Nuts - Quick Release (Relevance 1/10)
Carbon steel, black oxide finish. Button Thread® nuts allow quick fixturing on long thread lengths. Simply press the button and the threads are disengaged to allow easy movement up or down the screw. Release the button and the threads engage for normal turning.
|
Nuts - Well (Relevance 1/10)
Flanged neoprene bushing with a brass machine nut moulded into one end. Tightening a conventional machine screw threaded in a brass nut causes the insert to expand, making a secure fastening. 1. Place the Well Nut® insert all the way into a pre-drilled hole until the flange is firmly against the mounting surface. 2. Pass machine screw through part to be fastened and tighten until snug.
|
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Handles and Knobs | |
Knobs - Oval Tapered - Press On - Phenolic (Relevance 1/10)
Press on knobs hold on securely without threads or set screws
Shaft diameter should be +0.000 / - 0.076 mm for best performance Knob is held in place by a ribbed insert that squeezes onto the shaft. Eliminates machining costs Knobs will not come off with normal use but can be removed by knocking with a hammer on the underside.
|
Knobs - Pointer - Aluminium and Plastic (Relevance 1/10)
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
|
Knobs - Precision - Knurled (Relevance 1/10)
Set screw and clamp types - Stainless Steel. Also known as Thumb Knobs.
303 Stainless Steel. ID Tolerance +0.013 / -0.000 mm (+0.0005 / - 0.0000 inch).
|
Hobby Accessories | |
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Square - Miniature (Relevance 1/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Insert Bearings and Housings | |
Bearings - For Cast Iron Housings (Relevance 1/10)
With spherical OD for use with cast iron flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request. Lubrication Hole to match Lubrication groove in housing.
|
Bearings - For Pressed Metal Housings (Relevance 1/10)
With spherical OD for use with pressed metal flanged and pillow block housings.
Grub Screw locking. Preferred misallignment of no more than 2 Degrees, but can accommodate up to 6 Degrees. Also available with eccentric locking collars on request.
|
Kits | |
Assortment Kits - Various (Relevance 1/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Materials | |
Materials - Magnetic Sheeting (Relevance 1/10)
Magnetic sheeting is ideal for making small decorative magnets or for use on vehicles.
If cared for properly this magnetic material will not damage paintwork. Magnets should be removed weekly and the vehicle washed before re-applying Type 1: White on one side and magnetic on the other. Ordered per metre. Type 2: Rectangular sheets sticky on one side and magnetic on the other. Sheeting will be supplied in one length up to the max continuous length shown in the tables
|
Rod - Round - Urethane (Relevance 1/10)
Hard urethane rubber compound. Machinable. Length +/- 3.2mm. Diameter +/- 2 percent
|
Solarbotics Materials (Relevance 1/10)
Versatile material for building robots because of its ability to glue well with epoxy and superglue.
Can be easily shaped by immersing in hot water and bending to your desired shape while it cools. Can be easily cut, drilled and threaded for screw fasteners. Do not use black Sintra with solar powered robots as it may get soft on hot days.
|
Mounts and Vibration Control | |
Dampeners - Bushings - Silicone (Relevance 1/10)
Protects fragile subjects from micro-vibrations and light shocks.
Bolt not supplied. Collar : Brass. Bushing : Silicone Gel.
|
Mounts - Cylindrical - Female to Blank (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Female to Female (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Blank (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Female (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Male to Male (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
|
Mounts - Cylindrical - Square (Relevance 1/10)
Rubber hardness 60 Duro Standard unless otherwise noted
Fastener may be steel, brass or zinc plated. Natural Rubber isolator.
|
Mounts - Finger Flex Assemblies (Relevance 1/10)
Cadmium Plated Steel Housing. Natural Rubber Isolators. Natural Frequency 6-30 Hz.
|
Mounts - Square (Relevance 1/10)
Fastener may be steel, brass or zinc plated. Natural rubber isolator.
|
Pulleys | |
Pulleys - Flat Belt (Relevance 1/10)
Polycarbonate pulleys for flat belts 6mm or 6.35mm wide.
Aluminium Knurled Inserts. Gold Iridite Brass Knurled Inserts. Set Screw Locking.
|
Pulleys - U Groove - Steel (Relevance 1/10)
303 Stainless Steel. Groove has 1.57 mm Radius - 1.57mm Deep. 2 hub types - Pin Hub for use with Set Screws - Clamp Hub for use with Gear Clamps.
|
Seals and Sealing | |
Rings - Backup (Relevance 1/10)
Durometer 90 Nitrile Rubber back up rings.
|
Solar | |
Solar Cells (Relevance 1/10)
Uses include solar toys, solar challenge models, science kits, solar education kits etc
Most sizes in the EPSS and EPAS range can be ordered with Solder Pads, Screws, Alligator Clips, Banana Plugs or Connecting Wires attached.
|
Storage | |
Enclosures - Plastic ABS (Relevance 1/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Made with ABS Material, moulded in dark grey. Bosses on internal base allow fixing of PCBs horizontally, or connection of terminals, etc. The lid and base incorporate a tongue and groove sealing system with a neoprene gasket. Lid fixing screws are M4 stainless steel (non-metallic) into threaded brass inserts. Designed to IP65 of IEC529 and NEMS 4 (dust and hoseproof).
|
Straps - Cargo (Relevance 1/10)
Black rubber cargo straps with hooks. Stronger but less flexible than bungee straps.
|
Tools | |
Tools - General (Relevance 1/10)
Needle Files, Pin Vises, Gear Gauge, Wire and Tube Benders, Tube Cutters, Miniature tap, Turnbuckle Wrench, Shock Matching Tool and die set
X-Acto Knife Sets - Pin Vises - Screw Pitch Gauges and more
|
Tools - Thread Repair (Relevance 1/10)
Quickly repairs damaged screws
Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.
|
Washers | |
Washers - Cup - Aluminium (Relevance 1/10)
For countersunk screws.
Aluminium solid cup washers.
|
Washers - Cup - Stainless Steel (Relevance 1/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Self Aligning (Relevance 1/10)
AISI 303 Stainless Steel or Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
|
Wheels | |
Wheels - Drive - Friction (Relevance 1/10)
O-Ring tyre - Acetal body - Brass bore insert.
Brass Bore Insert. Acetal Body. Set Screw Locking. Buna N O-Ring Tyre - 70 Durometer. Bore tolerance +0.025/-0.000.
|
Wheels - Industrial - Budget (Relevance 1/10)
Inexpensive white plastic wheels with black rubber tires and small rubber wheels with aluminum hubs
General Duty Ideal for trolleys, lawn mowers and other Plain Centre
|
|
