Categories that include the terms: WASHERS and CUP and ALUMINIUM
|
Washers |  |
Washers - Cup - Aluminium (Relevance 10/10)
For countersunk screws.
Aluminium solid cup washers.
|
Washers - Cup - Stainless Steel (Relevance 9/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Flat - Aluminium (Relevance 9/10)
Flat washers.
|
Fasteners | |
Threaded Rod - Aluminium (Relevance 5/10)
UNC and UNF light weight aluminium.
|
Handles and Knobs | |
Knobs - Ball - Threaded - Polished Aluminium (Relevance 5/10)
DIN319 Tapped aluminium
Polished with a flash chrome finish
|
Materials | |
Sheet - Aluminium (Relevance 5/10)
Non precision inexpensive aluminium sheet for hobby applications.
Sheet for applications not requiring absolute precision. Thickness tolerances +/- 0.1mm Lengths and widths will be at least that specified but may be more.
|
Tube - Streamline - Aluminium (Relevance 5/10)
Streamline Aluminium Tubing.
Teardrop shaped soft aluminium tubing Enables easier bending Great for tight applications
|
Shim | |
Shim and Foil - Aluminium (Relevance 5/10)
Includes listing on 6061-T6 Aluminium Sheet. Very thin to thick sizes.
NOTE! Very thin sizes may experience some bending or indentations. This product is meant for engineering applications not decorative applications.
|
Spacers | |
Spacers - Round - Through Bore - Aluminium (Relevance 5/10)
Shaft spacers - Aluminium
|
Washers | |
Washers - Disc Spring - Carbon Steel (Relevance 5/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Disc Spring - Plastic (Relevance 5/10)
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
|
Washers - Disc Spring - Stainless Steel (Relevance 5/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Flat - Brass - Commercial (Relevance 5/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Brass - Precision (Relevance 5/10)
Precision Tolerances. Laminated brass shim washers.
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 5/10)
Flat Carbon Spring Steel Washers.
|
Washers - Flat - Commercial - All Types (Relevance 5/10)
Includes all materials listed in other commercial washer categories.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Fibre (Relevance 5/10)
Flat fibre washers.
|
Washers - Flat - Mild Steel (Relevance 5/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Nylon (Relevance 5/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - PTFE (Relevance 5/10)
Teflon Washers
|
Washers - Flat - PVC (Relevance 5/10)
Flat washers.
|
Washers - Flat - Precision - All Types (Relevance 5/10)
Includes all materials listed in other precision washer categories.
|
Washers - Flat - Sintered Bronze - Precision (Relevance 5/10)
Flat washers from oil impregnated sintered bronze
|
Washers - Flat - Stainless Steel - Commercial (Relevance 5/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Titanium - CP Grade 1 (Relevance 5/10)
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Spring (Relevance 5/10)
Wave Washers - All Materials.
|
Couplings | |
Couplings - Bellows - Set Screw - Aluminium (Relevance 4/10)
Zero Backlash - High Torsional Stiffness - Identical Clockwise and Anticlockwise Characteristics
Phosphor Bronze Bellows Aluminium Hubs
|
Fasteners | |
Nuts - Hexagonal - Aluminium (Relevance 4/10)
METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Nuts - Hexagonal - Nylon Insert - Aluminium (Relevance 4/10)
Nylon Insert for Locking. Not Nyloc™ brand.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering.
|
Screws - Machine - Aluminium (Relevance 4/10)
Metal Thread Screws UNC.
Nuts sold separately - See Fasteners - Nuts.
|
Screws - Socket - Button - Aluminium (Relevance 4/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN7380.
|
Screws - Socket - Cap - Aluminium (Relevance 4/10)
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
|
Screws - Socket - Countersunk - Aluminium (Relevance 4/10)
Flat Head Countersunk UNC - UNF - METRIC.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN7991.
|
Socket Set Screws - Cup Point - Standard (Relevance 4/10)
Standard grub screws. Includes alloy steel and stainless steel. UNC - UNF - BA - METRIC.
|
Handles and Knobs | |
Knobs - Pointer - Aluminium and Plastic (Relevance 4/10)
Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.
|
Hobby Condensed Selection | |
Hobby Washers - Precision Shim (Relevance 4/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Materials | |
Rod - Round - Aluminium (Relevance 4/10)
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Round - Aluminium (Relevance 4/10)
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. For use with bearings we suggest you use items from the category - Shafting - Ground. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Tube - Square - Aluminium (Relevance 4/10)
Hollow square tubing for general hobby applications.
Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
|
Plain Bearings | |
Bushes - Aluminium - Frelon Lined (Relevance 4/10)
Self lubricating - Replaces oilite or plastic bearings.
SLIP FIT: Housing bore should be OD +0.050/+0.075 - lock in place with retaining compound or epoxy. PRESS FIT: Housing bore should be OD -0.000/+0.010. Use freezing method for press fit assembly - freeze bearing to -18 Deg C for 30 minutes. Body: Aluminium. Lining: Frelon.
|
Rollers | |
Rollers - Idler - With Aluminium Sleeve (Relevance 4/10)
Tolerance of Roller Outside Diameter (D) is ±0.075 mm
|
Storage | |
Enclosures - Aluminium - 100 Series (Relevance 4/10)
Great little boxes ready for you to adapt to your mechanical or electrical projects.
Internal guide slots for mounting PCB assemblies vertically. Ideal for housing sensitive electrical, mechanical, pneumatic or hydraulic devices Provides effective shielding of EMI and RFI. Designed to IP65 of IEC529 and NEMA 4 (dust and hoseproof). The lid incorporates a recessed neoprene gasket.
|
Enclosures - Aluminium - Economy (Relevance 4/10)
Great little boxes ready for you to adapt to your mechanical projects.
Excellent screening properties for EMI and RFI Ideal for projects subject to weather Great housings for mechanical projects. Easy to machine. 380 Die Cast aluminium alloy BS1490 LM24 Close fitting flanged lids
|
Suction Cups | |
Suction Cups (Relevance 4/10)
|
Washers | |
Washers - Disk Lock (Relevance 4/10)
Stainless Grade Grade A2 302/316 18-8. Vibration-proof self tightening structural locking device. Maximum Working Temp: +430°C. DISC-LOCK® has outperformed all other types of loose, washered, threaded or pinned systems. in a wide range of high stress, corrosive, and vibration sensitive applications.
|
Washers - Finishing (Relevance 4/10)
|
Washers - Flat - High Tensile (Relevance 4/10)
ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Rubber (Relevance 4/10)
|
Washers - Flat - Stainless Steel - Precision (Relevance 4/10)
Precision Tolerances.
|
Washers - Lock - External Tooth - Spring Steel (Relevance 4/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 4/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 4/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 4/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Split (Relevance 4/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Tabbed - Heavy Duty (Relevance 4/10)
Heavy duty WH / TW Series for bearing locknuts.
Carbon spring steel. Use with NH series locknuts.
|
Washers - Nord Lock (Relevance 4/10)
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer.
|
Washers - Safety (Relevance 4/10)
Spring Steel Hardened Black.
|
Washers - Self Aligning (Relevance 4/10)
AISI 303 Stainless Steel or Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
|
Washers - Shoulder - Nylon (Relevance 4/10)
|
Bearings - Specialty | |
Bearings - Ceramic Si3N4 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Higher speed than Zr02.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. 3.2g/cubic cm density. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. Si3N4 (GSN-201) standard material for balls, cage and rings. HRC80 Hardness. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Ceramic ZrO2 (Relevance 1/10)
Excellent performance in electrical and magnetism sensitive applications. Not for High Speed.
Excellent performance in electrical and magnetism sensitive applications. Wear and corrosion resistance. Lubrication and maintenance free. Cages of PTFE or Glass Fibre Reinforced Nylon. Can be made from special aviation aluminum on request. ZrO2 standard material for balls, cage and rings. Si3N4 available to special order. High and low- temperature application. Up to 250 Deg C with PTFE Cage and 130 Deg C with Nylon Cage.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 1/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Bearings and Housings | |
Bearings - Press - Needle Roller - Flange Mounted (Relevance 1/10)
Fitted with drawn cup needle bearing. -30 to 110 Deg C. Retainer : Carbon Steel / Zinc Plated or Oxycote® Hardened to HRB 93.98. Shafts must be hardened to Rc 58 with 0.8um surface finish or finer.
|
Bearings - Spyraflo - Flanged Housing - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Flanged Housing - Washdown (Relevance 1/10)
Electroless nickel plated aluminum housing with self aligning Stainless Steel covered Acetal bearing.
See links at bottom of web page for more information +/- 5% Static Alignment Electroless nickel plated aluminium housing Corrosion Resistant Light weight
|
Bearings - Spyraflo - Pillow Block - Self Aligning (Relevance 1/10)
Robust light weight aluminium housing with self aligning needle roller or bronze bearings.
See links at bottom of web page for more information +/- 5% Static Alignment Sintered aluminium housing Corrosion Resistant Light weight
|
Housings - Bearing - Pillow Block - Miniature (Relevance 1/10)
Aluminium pillow block housings mounted with 440C stainless miniature bearings
No more need for expensive engineering of housings to suit your new applications. Fully greased Japanese 440C Grade corrosion resistant stainless steel ball bearings Double shielded bearings to minimise contamination
|
Clamping and Locking | |
Clamps - Gear - Screw Type (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Clamps - Gear - Split (Relevance 1/10)
Commercial - Precision - Stainless - Aluminium - Carbon Steel - For clamp type gears.
Precision Type : Height and Clearance Radii Tolerances +/- 0.397. Precision Type : All other dimensional tolerances except ID +/-0.127. Commercial Type : Height and Clearance Radii Tolerances +/- 0.794. Commercial Type : All other dimensional tolerances except ID +/-0.254. ID Tolerances - Refer to table.
|
Hubs - Bolt On (Relevance 1/10)
Aluminium Hub with Set Screws
|
Couplings | |
Couplings - Double Disk (Relevance 1/10)
Zero Backlash - High Torsional Stiffness.
Hub and Spacer: Aluminium Alloy. Pin and Disc: Stainless Steel. Max Axial Play: +/-0.5mm. 0.7 to 12.5 Nm. 3000 to 19000 rpm.
|
Couplings - Double Disk - High Torque (Relevance 1/10)
Zero Backlash - Clamp Locking - Medium torsional stiffness.
High torsional stiffness and high response. Zero backlash. Hub: Aluminium (A2017) Spacer: Aluminium (A2011). Pin: Stainless Steel (SUS301) Disk: Stainless Steel (SUS303). Maximum Temperature: +100°C. 2.8 to 22 Nm. 2400 to 4800 rpm. Identical clockwise & anti-clockwise rotational characteristics.
|
Couplings - Jaw Type - With Polyurethane Spider (Relevance 1/10)
Miniature aluminium curved jaw flexible couplings. 2 to 160 Nm.
Discs (either red as standard with blue or white optional) are available to purchase separately. Flexible couplings transmit torque and rotational angle while absorbing misalignment. When the misalignment exceeds allowable values, vibration may result or the life of the coupling may become shortened. Zero backlash in low torque application, made capable by having the hubs pressed in a spacer. Can be used as a flexible coupling in a high torque application.
|
Couplings - Slit Type (Relevance 1/10)
Aluminium - Stainless Steel - Flexible - Zero Backlash. 0.1 to 35 Nm. 2400 to 48000 rpm.
High Torsional Stiffness. Zero Backlash.
|
Fasteners | |
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Screws - Thumb - Plain (Relevance 1/10)
Brass, steel, aluminum and stainless and nylon.
|
Gearboxes | |
Gearboxes - Cross Axis - 47 x 40 x 22mm (Relevance 1/10)
Worm and Wormwheel box. 1.4 to 2.5Nm. 5:1 to 120:1 ratios. P20 and PF20.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 70 x 60 x 28mm (Relevance 1/10)
Worm and Wormwheel box. 2.5 to 8.8Nm. 5:1 to 120:1 ratios. P30 and PF30 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Cross Axis - 90 x 75 x 32mm (Relevance 1/10)
Worm and Wormwheel box. 5.0 to 18.0Nm. 5:1 to 120:1 ratios. P40 and PF40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Worm: High Carbon Steel 817M40 (40CrNiMo6). Wheel: Quality Aluminium Bronze (CA104 / AB2). Threaded Bearing Caps: Mild Steel, chemically blackened (Blackodised). Fasteners: Steel (non-plated). Bearings : Steel.
|
Gearboxes - Right Angle - 50.0 x 50.0 x 30.0mm (Relevance 1/10)
Economy Bevel Gear Type. GDRA Series.
Speeds up to 500 rpm. Bearings : Special resin and bronze with steel backing. Shafts : 303 Stainless Steel. Cover : Black plastic over black anodised aluminium housing. Gears : AISI 1045 steel.
|
Gearboxes - Right Angle - 75.0 x 75.0 x 44.0mm (Relevance 1/10)
BLH40 Series.
Case: AA15 Red Anodised Aluminum (6082-T6). Shaft Bevel: Hardened Alloy Steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) (8620) depending on manufacturer's preference. Threaded Bearing Caps: Mild Steel, chemically blackened (blackodised). Fasteners: Steel (non-plated) Bearings: Steel. Lubrication: Greased for life - Shell Alvania Grease HDX2.
|
Gears and Gearing | |
Gears - Internal - 24 Pitch (Relevance 1/10)
Various materials including 2024-T4 Aluminum, 303 stainless steel and brass.
|
Gears - Internal - Module 0.5 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 0.8 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Internal - Module 1 (Relevance 1/10)
2024-T4 Aluminum and 303 stainless steel.
|
Gears - Mitre - Module 0.6 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Stainless steel, brass, aluminium and acetal.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 1.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 2.5 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Mitre - Module 3 (Relevance 1/10)
1:1 Ratio. 20 Degree Pressure Angle - Steel, stainless steel, brass, aluminium, acetal and zinc die cast.
Mitre gears are used with a matching gear of the same pitch and number of teeth. This provides a 1:1 ratio on a 90 degree angle. See Gears - Bevel for other ratios.
|
Gears - Racks - 24 Pitch - 20 Degree (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 64 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 72 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 96 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - 120 Pitch (Relevance 1/10)
20 Degree Pressure Angle. 416 stainless steel and aluminium.
Metallic.
|
Gears - Racks - Flexible - Guide Rails (Relevance 1/10)
For mounting flexirack. Flexible nylon or rigid aluminium guide rails.
Longer lengths in Nylon available on special order.
|
Gears - Spur - 24 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 1.058mm (1/24 in.). 20 Degree Pressure Angle. 2024 aluminium, brass, acetal, 303 stainless steel, nylon, bakelite and alloy steel.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 24 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 32 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.794mm (1/32 in.). 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, acetal, bakelite, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 32 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 48 Pitch - 14.5 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 14.5 Degree Pressure Angle. 5052 aluminium, brass, carbon steel and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - 20 Degree (Relevance 1/10)
PCD = No. of Teeth x 0.529mm (1/48 in.). 20 Degree Pressure Angle. 2024 and 5052 aluminium, 303 stainless steel, acetal, brass and nylon.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 48 Pitch - Hub Mounting (Relevance 1/10)
Suits hub and cluster gears 9.525mm (3/8) mounting diameter as listed on this site. Aluminium, stainless steel and acetal.
Plastic and metallic.
|
Gears - Spur - 64 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.397mm (1/64 in.). 20 Degree Pressure Angle. 5052 aluminium, stainless steel, acetal and brass.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch (Relevance 1/10)
PCD = No. of Teeth x 0.353mm (1/72 in.). 20 Degree Pressure Angle. 2024 aluminium, stainless steel and acetal.
Plastic and metallic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - 72 Pitch - Differential End (Relevance 1/10)
To suit the precision diffs listed on this site. 2024 aluminium and 303 stainless steel.
Metallic.
|
Gears - Spur - Module 0.5 (Relevance 1/10)
PCD = No. of Teeth x 0.500mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 0.8 (Relevance 1/10)
PCD = No. of Teeth x 0.800mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears - Spur - Module 1 (Relevance 1/10)
PCD = No. of Teeth x 1.000mm. 20 Degree Pressure Angle. 2024 aluminium, 303 stainless steel, 416 stainless, acetal, AISI4135 steel, brass and carbon steel.
Metallic and plastic. Fairloc Hub Type require controlled shaft tolerances between 0.0025 and 0.0203 mm Clearance.
|
Gears and Gearing - Antibacklash | |
Gears - Spur - Antibacklash - 32 Pitch (Relevance 1/10)
Steel - Stainless Steel - Aluminium - 20 Degree Pressure Angle.
|
Gears and Gearing - Matched Sets | |
Gears - Bevel - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets. For 90 degree angle power transfer.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. See Gears - Mitre for 1:1 ratios.
|
Gears - Mitre - 48 Pitch - Precision Matched Sets (Relevance 1/10)
Sold as sets - 1:1 Ratio. Stainless steel and aluminium.
Stainless : 303 Stainless Steel. Aluminium : 2024-T4 or T351 Aluminium Alloy Anodised before cutting. AGMA Q10 Quality. 20 Degree Pressure Angle. Mitre gear sets provide a 1:1 ratio on a 90 degree angle.
|
Hobby Accessories | |
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
Housings to Suit Ball Bearings | |
Housings - Bearing - Square - Miniature (Relevance 1/10)
Aluminium housings to suit standard radial ball bearings.
Use with standard radial ball bearings. Bearing not included. Can be through screwed from the top using socket head cap screws. Can be bolted from the bottom using the pre-tapped holes. Made from Aluminium 6082-T6 Black Anodised.
|
Kits | |
Assortment Kits - Various (Relevance 1/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Linear Motion Bearings - Drylin | |
Linear Slide - Drylin - Carriage Assembly (Relevance 1/10)
Insensitive to dust and dirt. Match with Drylin Rail sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Slide - Drylin - Rail (Relevance 1/10)
Insensitive to dust and dirt. Match with Drylin Carriage Assembly sold seperately.
Match size 1 assembly with size 1 rail or size 2 assembly with size 2 rail. Flat and wide for supporting high moments. Low friction value for dry running. Rugged, corrosion-free and wear-resistant. Low noise operation - rail made of hard anodised aluminium - liners made from Iglidur J.
|
Linear Motion Bearings - Drylin Bushings | |
Drylin Sliding Bearings (Relevance 1/10)
Linear sliding motion. Use with Drylin Aluminium Shafts.
Sliding film Iglidur J. Maximum Mean Surface Pressure: 25 N/mm2. Highest Wear Resistance at loads: < 2 N/mm2. Maximum Speed: 8 m/s (dry) >10 m/s (lubricated) 1.5 m/s (rotating dry). Working Temp. Range: -60°C to +100°C (increased wear when used in excess of 80°C).
|
Pulleys | |
Pulleys - Flat Belt (Relevance 1/10)
Polycarbonate pulleys for flat belts 6mm or 6.35mm wide.
Aluminium Knurled Inserts. Gold Iridite Brass Knurled Inserts. Set Screw Locking.
|
Pulleys - Timing - 1.000mm Pitch - Suits 3mm Belts (Relevance 1/10)
Timing Pulleys to suit 1mm Pitch Timing Belts.
Aluminium Alloy
|
Pulleys - Timing - 1.000mm Pitch - Suits 6mm Belts (Relevance 1/10)
Timing Pulleys to suit 1mm Pitch Timing Belts.
Aluminium Alloy
|
Pulleys - Timing - 2.000mm Pitch - GT - To Suit 9mm Wide Belts (Relevance 1/10)
Timing Pulleys to suit 2mm Pitch GT Timing Belts 9mm Wide.
Aluminium Alloy
|
Rollers | |
Rollers - Urethane Feed - With Hub (Relevance 1/10)
Urethane coated aluminium alloy feed rollers with hub.
Roller - Urethane 60 Durometer, Ground Outside Diameter Sleeve - Aluminium
|
Shaft and Shafting | |
Supports - Flanged Two Bolt (Relevance 1/10)
For linear shafting.
Housing made of Cast Aluminium. Clamping Screw (supplied) made of Steel.
|
Supports - Pedestal Two Bolt (Relevance 1/10)
For linear shafting.
Cast Aluminium or Malleable Iron. Clamping Screw (supplied) made of Steel.
|
Shim | |
Shims - Arbor (Relevance 1/10)
Flat arbor shim washers.
|
Spacers | |
Spacers - Arbor (Relevance 1/10)
Flat arbor shim washers with keyway groove.
|
Springs | |
Spring Assemblies - Bracket - RINO (Relevance 1/10)
Spring: Stainless Steel 301 S21 Grade. Bobbin and Bracket: Nylon Moulded secured to aluminium sheet. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring. End holes are centred at the distances and diameters shown in the tables.
|
Spring Assemblies - Small Bracket - RINO (Relevance 1/10)
Spring: Stainless Steel 301 S21 Grade. Base: Aluminium Drum: High Impact Styrine. Constant force extension springs provide a huge range of application opportunities. Springs can be extended in excess of 50 times the relaxed length of the spring.
|
Storage | |
Bags and Cases (Relevance 1/10)
Carry bags and cases for your RC helicopters, cars and radio equipment. Aluminium and material cases.
These items may attract increased freight rates due to their size. We will contact you before charging your order if necessary.
|
Cases - Equipment (Relevance 1/10)
Aluminium cases for your hobby equipment.
These items may attract increased freight rates due to their size. We will contact you before charging your order if necessary.
|
Wheels | |
Wheels - Industrial - Budget (Relevance 1/10)
Inexpensive white plastic wheels with black rubber tires and small rubber wheels with aluminum hubs
General Duty Ideal for trolleys, lawn mowers and other Plain Centre
|
|
