Categories that include the term: WASHERS
|
Hobby Condensed Selection |  |
Hobby Washers - Precision Shim (Relevance 10/10)
A small selection of popular sizes.
See main listings for sizes not shown here.
|
Washers | |
Washers - Cup - Aluminium (Relevance 10/10)
For countersunk screws.
Aluminium solid cup washers.
|
Washers - Cup - Stainless Steel (Relevance 10/10)
For countersunk screws.
Stainless Steel cup washers.
|
Washers - Disc Spring - Carbon Steel (Relevance 10/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Disc Spring - Plastic (Relevance 10/10)
Also known as belleville washers.
Not for constant spring forces or when high forces are needed. Provides flat spring characteristics and compensates for axial clearances and tolerances. Vibration dampening and noise reduction. Electrical and thermal insulation. Non magnetic - Polysorb® material.
|
Washers - Disc Spring - Stainless Steel (Relevance 10/10)
Also known as belleville washers.
Manufactured under strict quality control to conform to DIN 2093
|
Washers - Disk Lock (Relevance 10/10)
Stainless Grade Grade A2 302/316 18-8. Vibration-proof self tightening structural locking device. Maximum Working Temp: +430°C. DISC-LOCK® has outperformed all other types of loose, washered, threaded or pinned systems. in a wide range of high stress, corrosive, and vibration sensitive applications.
|
Washers - Finishing (Relevance 10/10)
|
Washers - Flat - Aluminium (Relevance 10/10)
Flat washers.
|
Washers - Flat - Brass - Commercial (Relevance 10/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Brass - Precision (Relevance 10/10)
Precision Tolerances. Laminated brass shim washers.
|
Washers - Flat - Carbon Spring Steel - Precision (Relevance 10/10)
Flat Carbon Spring Steel Washers.
|
Washers - Flat - Commercial - All Types (Relevance 10/10)
Includes all materials listed in other commercial washer categories.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Fibre (Relevance 10/10)
Flat fibre washers.
|
Washers - Flat - High Tensile (Relevance 10/10)
ASTM F436 1985. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Mild Steel (Relevance 10/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - Nylon (Relevance 10/10)
Flat washers.
Please note! Tolerances for commercial grade washers are much larger than for precision washers. In most cases the actual washer size will be larger than the nominal ID and smaller than the nominal OD.
|
Washers - Flat - PTFE (Relevance 10/10)
Teflon Washers
|
Washers - Flat - PVC (Relevance 10/10)
Flat washers.
|
Washers - Flat - Precision - All Types (Relevance 10/10)
Includes all materials listed in other precision washer categories.
|
Washers - Flat - Rubber (Relevance 10/10)
|
Washers - Flat - Sintered Bronze - Precision (Relevance 10/10)
Flat washers from oil impregnated sintered bronze
|
Washers - Flat - Stainless Steel - Commercial (Relevance 10/10)
Flat washers.
Dimensions are nominal. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Flat - Stainless Steel - Precision (Relevance 10/10)
Precision Tolerances.
|
Washers - Flat - Titanium - CP Grade 1 (Relevance 10/10)
Flat washers. CP Grade 1 Titanium.
CP Grade 1. Commercially pure for general industrial corrosion applications. UNS R50250. Please note! Tolerances for commercial grade washers are much larger than for precision washers.
|
Washers - Lock - External Tooth - Spring Steel (Relevance 10/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - External Tooth - Stainless Steel (Relevance 10/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Spring Steel (Relevance 10/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Internal Tooth - Stainless Steel (Relevance 10/10)
These are not the same as push on retaining rings. This product is not designed to grip a shaft. Search for push on retaining rings if that is what you require.
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Split (Relevance 10/10)
Dimensions are nominal and may vary between batches.
|
Washers - Lock - Tabbed - Heavy Duty (Relevance 10/10)
Heavy duty WH / TW Series for bearing locknuts.
Carbon spring steel. Use with NH series locknuts.
|
Washers - Nord Lock (Relevance 10/10)
Supplied in pairs
Steel: Hardness HRA 75±3% (HRC48) Passivated Zinc Plated. ALWAYS LUBRICATE FASTENERS BEFORE REUSING. When reusing fasteners the friction is always higher. When tightening, a 20% higher torque should be applied than if tightening against a flat washer.
|
Washers - Safety (Relevance 10/10)
Spring Steel Hardened Black.
|
Washers - Self Aligning (Relevance 10/10)
AISI 303 Stainless Steel or Hardened steel 9 S Mn Pb 28 K DIN 6319. Order a base washer and an aligning washer to make a complete unit. Max Shaft Size Shown will allow 3 Degree of misalignment. DIN 6319-NI washers are used for clamping mechanical parts with non-parallel surfaces.
|
Washers - Shoulder - Nylon (Relevance 10/10)
|
Washers - Spring (Relevance 10/10)
Wave Washers - All Materials.
|
Dental Handpiece Parts | |
Several Dental Washers Parts (Relevance 8/10)
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
|
RC Nitro Engine Parts | |
40 Four Spline Prop Drive Washer - 78 Fox Parts (Relevance 8/10)
Bearings and Spare Parts for Remote Control Models
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
|
Bearings - Thrust | |
Bearings - Thrust - Roller (Relevance 3/10)
Washers and Rollers sold separately. Please select the appropriate washers (2) and roller assembly to complete a set.
Raceway hardness 58 HRC. Limiting Speeds are based on adequate oil lubrication. Load ratings are a guide taking into consideration ideal operating conditions. Dimensions given are nominal. Select the correct washer OD. Some washers listed here are to suit thrust ball bearings.
|
Kits | |
Assortment Kits - Various (Relevance 3/10)
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
|
Shim | |
Shims - Arbor (Relevance 3/10)
Flat arbor shim washers.
|
Spacers | |
Spacers - Arbor (Relevance 3/10)
Flat arbor shim washers with keyway groove.
|
Fasteners | |
Pins - Hammer Drive - Flat Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Pins - Hammer Drive - Round Head (Relevance 1/10)
Used to replace screws where the need to remove the pin is unlikely.
Low Carbon Steel (Series HP210) - self-colour, not plated cold formed pin. Simple, low cost assembly for use in mild steel, aluminium, brass or plastics. Secure - unlike a machine screw, a drive stud does not depend on tightening torque to be retained in the assembly. Drive studs do not require lock washers to prevent back-out. Designed for standard metric hole sizes and installation by hammer or press. Cold formed pins with helical knurls.
|
Hobby Accessories | |
Dubro Accessories Listed by Description (Relevance 1/10)
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings, Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns, Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws, Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders, Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
|
|
