Hobby & Engineering Supplies - an MBA company

Belts Timing Htd 5mm Categories


Belts - Timing - 5.080mm Pitch - XL - 7.9mm Wide
Belts - Timing -  5.080mm Pitch - XL -  7.9mm Wide

Also see combined categories:
All XL 5.08mm Pitch Timing Belts

Standard Series Timing Belts 5.080mm or 0.200 inch pitch.

Pitch (P) - 5.080mm (0.200 inch). Belts working load should be rated at approximately 1/15th of their ultimate breaking strength. Tooth Length (T) - 1.40mm. Tooth Height (H) - 1.30mm. Belt Height (W) - 2.30mm - Corner Radii ( r ) - 0.40mm. Breaking strength is not indicative of working strength.

Related Information:

There is also a good range of Belts - Timing - 5.080mm Pitch - XL - 7.9mm Wide on the Small Parts and Bearings website.


Belts - Vee - 10.0 x 5.5mm - M-3L
Belts - Vee - 10.0 x 5.5mm - M-3L

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 10.0mm Top Width x 5.5mm Height.

Sizes are nominal and may vary slightly. Items marked as Fractional Horsepower are designed for general purrpose low horseposer applications such as laundry machines, home workshop tools, small fans and blowers, garage equipment, small metal and woodworking tools etc. Belts shown as Fractional Horsepower type should not be used with reverse side idlers.

Related Information:

There is also a good range of Belts - Vee - 10.0 x 5.5mm - M-3L on the Small Parts and Bearings website.


Belts - Vee - 10.0 x 6.0mm - Z
Belts - Vee - 10.0 x 6.0mm - Z

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 10.0mm Top Width x 6.0mm Height.

Sizes are nominal and may vary slightly.

Related Information:

There is also a good range of Belts - Vee - 10.0 x 6.0mm - Z on the Small Parts and Bearings website.


Belts - Vee - 8.0 x 4.0mm
Belts - Vee -  8.0 x 4.0mm

Also see combined categories:
All Vee Belts 8mm and 10mm Top Width

Miniature and small belts. 8.0mm Top Width x 4.0mm Height.

Sizes are nominal and may vary slightly.

Related Information:

There is also a good range of Belts - Vee - 8.0 x 4.0mm on the Small Parts and Bearings website.


Belt CP 2 E-Sky Parts
Belt CP 2 E-Sky Parts


Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Belt CP E-Sky Parts
Belt CP E-Sky Parts


Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


KA85 Belt Sander Black and Decker Parts
KA85 Belt Sander Black and Decker Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of KA85 Belt Sander Black and Decker Parts on the Small Parts and Bearings website.


BSG-151 Belt Sander Ozito Parts
BSG-151 Belt Sander Ozito Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of BSG-151 Belt Sander Ozito Parts on the Small Parts and Bearings website.


BSR-1000 Belt Sander Ozito Parts
BSR-1000 Belt Sander Ozito Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of BSR-1000 Belt Sander Ozito Parts on the Small Parts and Bearings website.


BSR-800 Belt Sander Ozito Parts
BSR-800 Belt Sander Ozito Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of BSR-800 Belt Sander Ozito Parts on the Small Parts and Bearings website.


1-10 Belt Drive Colt Parts
1-10 Belt Drive Colt Parts


Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


TA03 - TA03F Chassis Belt Drive Tamiya Parts
TA03 - TA03F Chassis Belt Drive Tamiya Parts


Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Freejet Hoover Parts
Freejet Hoover Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Freejet Hoover Parts on the Small Parts and Bearings website.


Multi Models Dyson Parts
Multi Models Dyson Parts


Bearings and Spare Parts

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.

There is also a good range of Multi Models Dyson Parts on the Small Parts and Bearings website.


RC Spare Parts - Colt
RC Spare Parts - Colt


Colt spare parts listed by description. Includes 1/10 Belt Drive, Colt Buggy, GP, EVO7, Nissan Silvia, 2WD, 4WD, Toyota IS200, Monster Truck, EP Touring Car, MT Truggy, Mini Cooper, Shaft Drive

Refer to your parts manual to ensure you purchase the correct items.


Tools - Nitro Engine Starter and Accessories
Tools - Nitro Engine Starter and Accessories

Also see combined categories:
All Tools

Pocket staters, Bump Starts and belts



Pulleys - U Groove - Plastic - Hobby
Pulleys - U Groove - Plastic - Hobby

Also see combined categories:
All U Groove Bearings and Pulleys

Plastic with no locking method. Use with O-Rings or Rounthane Belts.

Related Information:


RC Spare Parts - Great Vigor
RC Spare Parts - Great Vigor


Great Vigor spare parts listed by description. Parts to suit 1/10 scale, 1/6 scale, Buggies, Truggies, 2WD, 4WD, BV1, Cage Buggy, Belt Crusher, Electrafun, Nitro Cage, Hunter Buggy, Rex-x



RC Spare Parts - Venom
RC Spare Parts - Venom


Venom Hobby Parts listed by description. Parts for 1/10 crawler, Baja, 1/8 scale cars, Beacon, Corsair, CPR Creeper, D Micro, DXL, EKOS, EPO, GPV-1, MINIZ, Island Hopper, King, Segad, KOS, KWA, M05, ME-109, MTT, Night Ranger 3D, Outlaw RC, Ozone Heli

Parts also to suit P-51, Texan, Savage, Scorpion AX10, Skywolf 3CH, Strait Jacket, TraXXas, TRX Slash. Ailerons fittings, Anti-rotation arm, A arms, Axle, Bag, Ball end, batteries assembleys, battery(bags, bars, box, case, charger, holder), beadlock, bearing kits, retainers and set. bell crank, blade grips and sets, body posts, bolt, bracket, bulkhead, cables, camber gauge, canopy, caps, carburettor, charger, chassis covers and plates. Cockpit cover, Collars, connectors, control links, control links, tray and units, coupler, cowl, crankcase, crankshaft, cylinder, Damper, decal set, differential (case, housing and system). Dig unit, drive (belt and dog), driveline, electronics unit, elevator, e-ring, ESC, exhaust (coupler, deflector and pipe), fail safes, feathering spindle.


Hobby Gears - Spur - Module 0.5
Hobby Gears - Spur - Module 0.5


A small selection of popular Module 0.5 Brass Gear Sets 9 to 20 teeth

See main listings under Gears for sizes not listed here. To work out the pitch diameter of a metric spur gear, multiply the no of teeth by the module. A module 0.5 spur gear with 20 teeth has a pitch diameter of 10mm. A module 0.5 spur gear with 10 teeth has a pitch diameter of 5mm.

Related Information:

There is also a good range of Hobby Gears - Spur - Module 0.5 on the Small Parts and Bearings website.


Eight-T Bearings Losi Parts
Eight-T Bearings Losi Parts


Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


RC Spare Parts - E-Sky
RC Spare Parts - E-Sky


E-Sky helicopter spare parts listed by description. Parts to suit Belt-CP V1 and V2, Honey Bee King, Big Lama, Cocomanche, Dauphin, Esmart, Hunter, KOB, Lama, Robins



LOSB0085 1-8-Scale 8IGHT-T 2.0 RTR 4WD Nitro Trugg Losi Parts
LOSB0085 1-8-Scale 8IGHT-T 2.0 RTR 4WD Nitro Trugg Losi Parts


Bearings and Spare Parts for Remote Control Models

Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.


Knobs - Pointer - Arrow Top
Knobs - Pointer - Arrow Top

Also see combined categories:
All Pointer Knobs

Push on. Suits 6.35mm (1/4 inch) shaft.


There is also a good range of Knobs - Pointer - Arrow Top on the Small Parts and Bearings website.


Knobs - Pointer - Skirted
Knobs - Pointer - Skirted

Also see combined categories:
All Pointer Knobs

Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass insert.


There is also a good range of Knobs - Pointer - Skirted on the Small Parts and Bearings website.


Knobs - Pointer - Black Aluminium
Knobs - Pointer - Black Aluminium

Also see combined categories:
All Pointer Knobs

Grub screw fixing. Suits 6.35mm (1/4 inch) shaft.


There is also a good range of Knobs - Pointer - Black Aluminium on the Small Parts and Bearings website.


Knobs - Pointer - Aluminium and Plastic
Knobs - Pointer - Aluminium and Plastic

Also see combined categories:
All Pointer Knobs

Grub screw fixing. Suits 6.35mm (1/4 inch) shaft. Brass Insert. White Pointer.


There is also a good range of Knobs - Pointer - Aluminium and Plastic on the Small Parts and Bearings website.


Motors - DC 12.0X30.0 mm
Motors - DC 12.0X30.0 mm

Also see combined categories:
All DC Motors

6.0V - 22800 RPM


Related Information:

There is also a good range of Motors - DC 12.0X30.0 mm on the Small Parts and Bearings website.


Motors - DC 16.6X32.0 mm
Motors - DC 16.6X32.0 mm

Also see combined categories:
All DC Motors

M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:

There is also a good range of Motors - DC 16.6X32.0 mm on the Small Parts and Bearings website.


Motors - DC 18.9X18.0X9.5 mm
Motors - DC 18.9X18.0X9.5 mm

Also see combined categories:
All DC Motors

M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams.

Related Information:

There is also a good range of Motors - DC 18.9X18.0X9.5 mm on the Small Parts and Bearings website.


Motors - DC 20.0X25.0 mm
Motors - DC 20.0X25.0 mm

Also see combined categories:
All DC Motors

1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts


Related Information:

There is also a good range of Motors - DC 20.0X25.0 mm on the Small Parts and Bearings website.


Motors - DC 22.4X38.0 mm
Motors - DC 22.4X38.0 mm

Also see combined categories:
All DC Motors


Related Information:

There is also a good range of Motors - DC 22.4X38.0 mm on the Small Parts and Bearings website.


Motors - DC 23.8X30.6 mm
Motors - DC 23.8X30.6 mm

Also see combined categories:
All DC Motors

12 VDC - 12,300 RPM unloaded at 4.5 volts


Related Information:

There is also a good range of Motors - DC 23.8X30.6 mm on the Small Parts and Bearings website.


Motors - DC 24.3X12.35 mm
Motors - DC 24.3X12.35 mm

Also see combined categories:
All DC Motors

6.0 VDC - 4,900 RPM unloaded at 4.5 volts


Related Information:

There is also a good range of Motors - DC 24.3X12.35 mm on the Small Parts and Bearings website.


Motors - DC 25.0x20.1X15.1 mm
Motors - DC 25.0x20.1X15.1 mm

Also see combined categories:
All DC Motors

M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:

There is also a good range of Motors - DC 25.0x20.1X15.1 mm on the Small Parts and Bearings website.


Motors - DC 25.0X21.0 mm
Motors - DC 25.0X21.0 mm

Also see combined categories:
All DC Motors

M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:

There is also a good range of Motors - DC 25.0X21.0 mm on the Small Parts and Bearings website.


Motors - DC 26.9X23.8 mm
Motors - DC 26.9X23.8 mm

Also see combined categories:
All DC Motors

M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:

There is also a good range of Motors - DC 26.9X23.8 mm on the Small Parts and Bearings website.


Motors - DC 26.9X24.2X18.3 mm
Motors - DC 26.9X24.2X18.3 mm

Also see combined categories:
All DC Motors

MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM. Standard 130 Size Hobby Motor.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:

There is also a good range of Motors - DC 26.9X24.2X18.3 mm on the Small Parts and Bearings website.


Motors - DC 30.5X24.2 mm
Motors - DC 30.5X24.2 mm

Also see combined categories:
All DC Motors

M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:

There is also a good range of Motors - DC 30.5X24.2 mm on the Small Parts and Bearings website.


Motors - DC 30.5X24.2X18.3 mm
Motors - DC 30.5X24.2X18.3 mm

Also see combined categories:
All DC Motors

MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.

See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.

Related Information:

There is also a good range of Motors - DC 30.5X24.2X18.3 mm on the Small Parts and Bearings website.


Motors - DC 36.0X71.0 mm
Motors - DC 36.0X71.0 mm

Also see combined categories:
All DC Motors

High power, high speed 11,800 RPM unloaded at 12 volts


Related Information:

There is also a good range of Motors - DC 36.0X71.0 mm on the Small Parts and Bearings website.


Motors - DC 8.0X10.0 mm
Motors - DC 8.0X10.0 mm

Also see combined categories:
All DC Motors

3.5V - 20500 RPM


Related Information:

There is also a good range of Motors - DC 8.0X10.0 mm on the Small Parts and Bearings website.


Couplings - Rigid - Hobby - Brass
Couplings - Rigid - Hobby - Brass

Also see combined categories:
All Rigid Couplings

A selection of inexpensive brass couplings for shaft sizes from 2 to 5 mm.


Related Information:

There is also a good range of Couplings - Rigid - Hobby - Brass on the Small Parts and Bearings website.


Washers - Lock - Split - Titanium CP Grade 1
Washers - Lock - Split - Titanium CP Grade 1

Also see combined categories:
All Split Lock Washers
All Lock Washers

CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Dimensions are nominal and may vary between batches. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

There is also a good range of Washers - Lock - Split - Titanium CP Grade 1 on the Small Parts and Bearings website.


Nuts - Hexagonal - Titanium - CP Grade 1
Nuts - Hexagonal - Titanium - CP Grade 1

Also see combined categories:
All Nuts

Metric Only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

There is also a good range of Nuts - Hexagonal - Titanium - CP Grade 1 on the Small Parts and Bearings website.


Screws - Cap - Socket - Titanium CP Grade 1 - DIN912
Screws - Cap - Socket - Titanium CP Grade 1 - DIN912

Also see combined categories:
All Machine Screws
All Socket Cap Screws

Metric Sizes to DIN912. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

Related Information:

There is also a good range of Screws - Cap - Socket - Titanium CP Grade 1 - DIN912 on the Small Parts and Bearings website.


Screws - Countersunk - Titanium CP Grade 1 - Philips Drive
Screws - Countersunk - Titanium CP Grade 1 - Philips Drive

Also see combined categories:
All Machine Screws

Flat Head Countersunk. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

Related Information:

There is also a good range of Screws - Countersunk - Titanium CP Grade 1 - Philips Drive on the Small Parts and Bearings website.


Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991
Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991

Also see combined categories:
All Countersunk Screws

Flat Head Countersunk. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Metric Sizes to DIN7991. Used in critical aircraft structural components. UNS R56400. ISO 10642. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.

Related Information:

There is also a good range of Screws - Countersunk - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN7991 on the Small Parts and Bearings website.


Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916
Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916

Also see combined categories:
All Non Magnetic Grub Screws
All Grub Screws

Standard DIN913 grub screws. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

Related Information:

There is also a good range of Socket Set Screws - Cup Point - Titanium - CP Grade 1 - DIN916 on the Small Parts and Bearings website.


Screws - Hex Head - Titanium CP Grade 1
Screws - Hex Head - Titanium CP Grade 1

Also see combined categories:
All Hex Head Screws

Fully threaded hex head set screws (DIN933). CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.

Din 933. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.

Related Information:

There is also a good range of Screws - Hex Head - Titanium CP Grade 1 on the Small Parts and Bearings website.


Main Pages



Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Hobby & Engineering Supplies Pty Ltd (ABN 54 125 001 541)

Hobby and Engineering Supplies offers 6213 products in 445 categories including assortment kits, low priced hobby bearings, tools, screws, brass and aluminium rod and tubing - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Hobby and Engineering Supplies is part of MBA Group offering a select range from the MBA Group catalogue.

Hobby and Engineering Supplies products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Hobby and Engineering Supplies 1997. All rights reserved.

Freight Rates
Terms and Conditions
Privacy Policy

Registered Australian Company: Hobby & Engineering Supplies Pty Ltd (ABN 54 125 001 541)

Hobby and Engineering Supplies offers 6213 products in 445 categories including assortment kits, low priced hobby bearings, tools, screws, brass and aluminium rod and tubing - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.

Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.

Hobby and Engineering Supplies is part of MBA Group offering a select range from the MBA Group catalogue.

Hobby and Engineering Supplies products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.

Information on this website is Copyright Hobby and Engineering Supplies 1997. All rights reserved.