Bungs And Caps Reversible Round Categories
Bungs
Bungs and Caps - Reversible - Round
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
There is also a good range of Bungs and Caps - Reversible - Round on the Small Parts and Bearings website.
Gearmotors - DC - Low Voltage
Reversible - Low Voltage - Self Starting.
Reversible. Low Voltage. Self Starting. Housing : Plastic / Shaft : Steel.
There is also a good range of Gearmotors - DC - Low Voltage on the Small Parts and Bearings website.
Bungs - Round
Plastic bungs fit inside round tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
There is also a good range of Bungs - Round on the Small Parts and Bearings website.
Screws - Round Head - Brass - Slotted
Brass metal thread machine screws BSW - UNF - UNC
Nuts sold seperately - See Nuts.
Related Information:
There is also a good range of Screws - Round Head - Brass - Slotted on the Small Parts and Bearings website.
Spacers - Round - Hobby
Inexpensive nylon spacers for hobby applications
There is also a good range of Spacers - Round - Hobby on the Small Parts and Bearings website.
Spacers - Round - Through Bore - Aluminium
Shaft spacers - Aluminium
There is also a good range of Spacers - Round - Through Bore - Aluminium on the Small Parts and Bearings website.
Rod - Round - Acetal
Hard, stiff plastic for machining bushes, gears etc with close tolerances. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.41 g/cm3 - Operating Temp -40 to 120 C. Tensile Strength 60-70 Mpa / Hardness 80 Rockwell M. Small diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
There is also a good range of Rod - Round - Acetal on the Small Parts and Bearings website.
Rod - Round - Aluminium
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
Related Information:
There is also a good range of Rod - Round - Aluminium on the Small Parts and Bearings website.
Rod - Round - Brass
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
Related Information:
There is also a good range of Rod - Round - Brass on the Small Parts and Bearings website.
Rod - Round - Carbon Fibre
High impact light weight carbon fibre for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
There is also a good range of Rod - Round - Carbon Fibre on the Small Parts and Bearings website.
Rod - Round - Nylon
High impact strength and toughness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.13 g/cm3 - Operating Temp -40 to 160 C. Tensile Strength 78 Mpa / Hardness 82 Rockwell M. Co-efficient of friction 0.20-0.30. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
There is also a good range of Rod - Round - Nylon on the Small Parts and Bearings website.
Rod - Round - Polyester PETP
High mechanical strength, stiffness and hardness. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 1.39 g/cm3 - Operating Temp 115 C / 5000 hrs - 100 C / 20000 hrs. Tensile Strength 90 Mpa. Hardness 96 Rockwell M. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
There is also a good range of Rod - Round - Polyester PETP on the Small Parts and Bearings website.
Rod - Round - PTFE
Lowest co-efficient of friction. Excellent chemical resistance. Sizes listed are FINISHED SIZE. Product supplied will be larger.
Specific Gravity 2.20 g/cm3 - Operating Temp -260 to 260 C. Tensile Strength 10-40 Mpa / Hardness D50-55 Shore. Co-efficient of friction 0.05-0.20. Smaller diameters may not be perfectly straight. Sizes listed are FINISHED SIZE. Product supplied will be larger to allow for machining. As this product requires machining, larger diameters may be supplied in lieu to expedite your order.
Related Information:
There is also a good range of Rod - Round - PTFE on the Small Parts and Bearings website.
Rod - Round - Soft Metal Packs
For general hobby applications. This rod is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths for general hobby applications. Not recommended for heavy duty applications. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
There is also a good range of Rod - Round - Soft Metal Packs on the Small Parts and Bearings website.
Rod - Round - Stainless Steel
For general hobby applications.
NOTE! Very thin sizes may experience some bending. They may not be straight for the entire length. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
Related Information:
There is also a good range of Rod - Round - Stainless Steel on the Small Parts and Bearings website.
Rod - Round - Urethane
Hard urethane rubber compound. Machinable.
Length +/- 3.2mm. Diameter +/- 2 percent.
Related Information:
There is also a good range of Rod - Round - Urethane on the Small Parts and Bearings website.
Tips - Round
Plastic tips fit over outside of tubing.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene. Tips may be supplied tapered or cylindrical depending on stock availability.
There is also a good range of Tips - Round on the Small Parts and Bearings website.
Tube - Round - Acrylic
Acrylic Transparent Tube
Acrylic also called Poly Methyl Methacrylate (PMMA) is a transparent thermoplastic often used as light weight or shatter-resistant alternatives to glass. Acrylic is an economical alternative to polycarbonate when extreme strength is not necessary. Additionally, doesn't contain potentially harmful bisphenol-A subunits. Often preferred because of moderate properties, easy handling and processing and low cost. Acrylic in the form off tubes affords hatter resistant panels for making rotating shafts, spacers, display and many other applications. Please note this item is not a precision item. The inside diameter is not toleranced and may vary between batches.
There is also a good range of Tube - Round - Acrylic on the Small Parts and Bearings website.
Tube - Round - Aluminium
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. E-mail sales@smallparts.com.au with enquiries.
Related Information:
There is also a good range of Tube - Round - Aluminium on the Small Parts and Bearings website.
Tube - Round - Brass
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. E-mail sales@smallparts.com.au with enquiries.
Related Information:
There is also a good range of Tube - Round - Brass on the Small Parts and Bearings website.
Tube - Round - Bronze - LG2 Standard
Leaded Gunmetal Bronze tubing. Product will machine to the sizes listed and is supplied will be larger on OD and smaller on bore.
Sizes listed are FINISHED SIZE. Product supplied will be larger on OD and smaller on bore. Longer lengths available on special request. Composition (Approx.) : Copper 85%, Tin 5%, Zinc 5%, Lead 5%. AS1565-83600 / Hardness : 70-90 BHN. Some items may be available in longer or shorter lengths. e-mail sales@smallparts.com.au with enquiries.
Related Information:
There is also a good range of Tube - Round - Bronze - LG2 Standard on the Small Parts and Bearings website.
Tube - Round - Carbon Fibre
High impact light weight carbon fibre hollow tubing for modelling.
Pultruded carbon fibre with a smooth epoxy coated finish. Items marked as Low Grade may have tolerance variations up to 0.2mm.
There is also a good range of Tube - Round - Carbon Fibre on the Small Parts and Bearings website.
Tube - Round - Copper
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft. Many sizes fit neatly into larger sizes to allow for telescoping size applications. Some items may be available in longer or shorter lengths. E-mail sales@smallparts.com.au with enquiries.
Related Information:
There is also a good range of Tube - Round - Copper on the Small Parts and Bearings website.
Tube - Round - Soft Metal Packs
For general hobby applications. This tube is annealed soft to make it easier to bend. Copper, brass and aluminium,
300mm lengths for general hobby applications. Not recommended for heavy duty applications. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
There is also a good range of Tube - Round - Soft Metal Packs on the Small Parts and Bearings website.
Tube - Round - Stainless Steel
Hollow round tubing for general hobby applications.
For general hobby applications. May be slightly oversized on OD so some reworking may be required before fitting closely mating parts such as bearings. This product is not recommended for use as a bearing shaft. We suggest you use items from the category - Shafting - Ground for bearing shaft.
Related Information:
There is also a good range of Tube - Round - Stainless Steel on the Small Parts and Bearings website.
Balsa Wood - Dowel
Round section dowel. Delivery Surcharges May Apply on Selected Items
This surcharge covers the protective packing required for shipping. Items over 1000mm long will require courier door to door delivery. Balsa sizes are approximate only. A $10.00 surcharge will apply to all orders of Balsa Wood delivered. Balsa Sheets, Block, Dowel, Leading Edge, Rectangle, Square.
Related Information:
There is also a good range of Balsa Wood - Dowel on the Small Parts and Bearings website.
Tools - Die Holders
Bar and round holders. 16mm, 20.64mm and 25.4mm (inch). Also called a button die stock.
There is also a good range of Tools - Die Holders on the Small Parts and Bearings website.
Switches - Rocker
20mm Diameter mounting hole 12V/10amp. On/Off Round Switches with Housing. Illuminates when turned to on position.
Switchs are rated at 10amp @ 600VAC with finger safe screw terminals.
There is also a good range of Switches - Rocker on the Small Parts and Bearings website.
Screws - Pan Head - 303-304 Stainless - Philips
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
Related Information:
There is also a good range of Screws - Pan Head - 303-304 Stainless - Philips on the Small Parts and Bearings website.
Bungs - Rectangular
Plastic bungs fit inside rectangular tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
There is also a good range of Bungs - Rectangular on the Small Parts and Bearings website.
Bungs - Square
Plastic bungs fit inside square tube.
Other colours available on request. Minimum quantities will apply. Made from tough polyethylene.
Related Information:
There is also a good range of Bungs - Square on the Small Parts and Bearings website.
Snap Buttons - Double End
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
There is also a good range of Snap Buttons - Double End on the Small Parts and Bearings website.
Snap Buttons - Single End - Dog Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
There is also a good range of Snap Buttons - Single End - Dog Leg on the Small Parts and Bearings website.
Snap Buttons - Single End - Spring Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
There is also a good range of Snap Buttons - Single End - Spring Leg on the Small Parts and Bearings website.
Caps - End - Kite
End caps with string holes and grooves for kite rods.
Joiners and connectors suitable for rod and tubing as well as for kites.
There is also a good range of Caps - End - Kite on the Small Parts and Bearings website.
Screws - Cap - Socket - 303 - 304 Stainless
UNC - UNF - METRIC - Stainless Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
Related Information:
There is also a good range of Screws - Cap - Socket - 303 - 304 Stainless on the Small Parts and Bearings website.
Screws - Cap - Socket - Alloy Steel
UNC - UNF - METRIC - Alloy Steel.
Imperial Sizes to ANSI B18.3. Metric Sizes to DIN912.
Related Information:
There is also a good range of Screws - Cap - Socket - Alloy Steel on the Small Parts and Bearings website.
Screws - Cap - Socket - Aluminium
Variety of colours available.
Other colours available on request. Minimum quantities will apply. Metric Sizes to DIN912.
Related Information:
There is also a good range of Screws - Cap - Socket - Aluminium on the Small Parts and Bearings website.
Screws - Cap - Socket - Titanium CP Grade 1 - DIN912
Metric Sizes to DIN912. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.
Related Information:
There is also a good range of Screws - Cap - Socket - Titanium CP Grade 1 - DIN912 on the Small Parts and Bearings website.
Screws - Cap - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN912
Metric Sizes to DIN912. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Used in critical aircraft structural components. UNS R56400. Composition Percentage: Al 5.5-6.75, V 3.5-4.5, N 0.05, C 0.08, H 0.015, Fe 0.40, O 0.2, Ti Balance. Grade 5 6Al-4V is a high strength titanium alloy. Tensile Strength 91.5kgf / mm2. Yield Strength 84.5kgf / mm2. Elongation 10 Percent.
Related Information:
There is also a good range of Screws - Cap - Socket - Titanium Ti-Gr5 - Ti-6Al4v - DIN912 on the Small Parts and Bearings website.
Bearings - Unground
Unground bearings used in trolleys, prams and wheel barrow wheels
There is also a good range of Bearings - Unground on the Small Parts and Bearings website.
Shafting - Ground - Hobby - Steel
Silversteel shafting for hobbies. Not suitable for precision bearings.
Suitable for use with plastic gears, bushes, couplings etc. Not recommended for use with precision steel or stainless steel bearings. Some sizes have special features such as serrations or small barbs (noted in description). Unground ends. Ideal for axles in robotic applications and educational projects.
Related Information:
There is also a good range of Shafting - Ground - Hobby - Steel on the Small Parts and Bearings website.
Shafting - Unground - Silver Steel
Unhardened silversteel shafting for general purposes. Not suitable for precision bearings until machined to correct tolerances and hardened.
See also drill rod. Drill Rod.
Related Information:
There is also a good range of Shafting - Unground - Silver Steel on the Small Parts and Bearings website.
Madcap Tamiya Parts
Bearings and Spare Parts for Remote Control Models
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
RC Spare Parts - Venom
Venom Hobby Parts listed by description. Parts for 1/10 crawler, Baja, 1/8 scale cars, Beacon, Corsair, CPR Creeper, D Micro, DXL, EKOS, EPO, GPV-1, MINIZ, Island Hopper, King, Segad, KOS, KWA, M05, ME-109, MTT, Night Ranger 3D, Outlaw RC, Ozone Heli
Parts also to suit P-51, Texan, Savage, Scorpion AX10, Skywolf 3CH, Strait Jacket, TraXXas, TRX Slash. Ailerons fittings, Anti-rotation arm, A arms, Axle, Bag, Ball end, batteries assembleys, battery(bags, bars, box, case, charger, holder), beadlock, bearing kits, retainers and set. bell crank, blade grips and sets, body posts, bolt, bracket, bulkhead, cables, camber gauge, canopy, caps, carburettor, charger, chassis covers and plates. Cockpit cover, Collars, connectors, control links, control links, tray and units, coupler, cowl, crankcase, crankshaft, cylinder, Damper, decal set, differential (case, housing and system). Dig unit, drive (belt and dog), driveline, electronics unit, elevator, e-ring, ESC, exhaust (coupler, deflector and pipe), fail safes, feathering spindle.
There is also a good range of RC Spare Parts - Venom on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Small Bearings
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Hobby & Engineering Supplies Pty Ltd (ABN 54 125 001 541)
Hobby and Engineering Supplies offers 6307 products in 341 categories including low priced hobby bearings, screws, brass and aluminium rod and tubing, shim - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Hobby and Engineering Supplies is part of MBA Group offering a select range from the MBA Group catalogue.
Hobby and Engineering Supplies products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Hobby and Engineering Supplies 1997. All rights reserved.
