Spring Motors Categories
Spring Motors - SDP
301 stainless Steel. Shipped as shown to be mounted on drums (not supplied) of the recommended diameters. Torque ratings listed are for the unwinding portion of the cycle. Torque at fully wound end of cycle will be slightly higher.
There is also a good range of Spring Motors - SDP on the Small Parts and Bearings website.
Collectibles - Metal Motorcycles
Beautiful model motorbikes in various styles including choppers, road bikes and vintage designs.
Made from industrial parts including bearings, screws, nuts, springs, chain links, rod, tubing and other parts. Two colours available - gunmetal grey or copper finish. Each bike is hand made, and therefore there may be minor differences between the bikes of a particular model. Re-Cycle motorbikes are a limited edition set of 20.
There is also a good range of Collectibles - Metal Motorcycles on the Small Parts and Bearings website.
Springs - Compression - Stainless Steel
This category includes short and long lengths
Standard springs may or may not be supplied with ends ground flush. If the end type is important to your application please contact us for more information or a special quote.
Related Information:
There is also a good range of Springs - Compression - Stainless Steel on the Small Parts and Bearings website.
Springs - Constant Force
301 Stainless Steel
Mounting hole specifications will be supplied on request. These springs are usually mounted on a drum and the free end attached to a loading force like a counterbalance. Free ID may vary to meet load specification. Load capacity can be increased by using multiple strips in tandem, back to back or laminated. Be sure to leave at least 40mm coiled on the drum at full extension. The spring ID will wrap tightly on the drum so that most applications require no fastening to the drum.
Related Information:
There is also a good range of Springs - Constant Force on the Small Parts and Bearings website.
Springs - Extension - Stainless Steel
Includes long lengths up to 1 metre
Zinc Plated Spring Steel not recommended for applications exceeding 121 oC (250 Deg F). 302 Stainless springs not recommended for applications exceeding 260 oC (500 Deg F). 302 stainless steel is slightly magnetic.
Related Information:
There is also a good range of Springs - Extension - Stainless Steel on the Small Parts and Bearings website.
Strip - Spring Steel
Hundreds of uses.
Hardened and tempered spring steel strip. Note that the width of this strip may vary minus nothing to plus 25 percent as it is guillotine cut from sheet. If you require a closer tolerance on the strip width please contact us prior to ordering.
There is also a good range of Strip - Spring Steel on the Small Parts and Bearings website.
Wire - Steel - Spring - Music Wire - Short Lengths
SAE 1090 Spring Steel. Includes inch and metric sizes.
Shipped in straight lengths on wooden backing board. Metric and imperial.
Related Information:
There is also a good range of Wire - Steel - Spring - Music Wire - Short Lengths on the Small Parts and Bearings website.
Snap Buttons - Single End - Spring Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
There is also a good range of Snap Buttons - Single End - Spring Leg on the Small Parts and Bearings website.
Assortment Kits - Various
Springs - O-Rings - Shafting - Circlips - Gears - Chain - Machine Keys - Nuts - Bolts - Shim - Screws - Washers - Roll Pins - Woodruff Keys - Cotter Pins - E-Clips - Fuses - Grease Nipples - Hitch Pins - Clevis Pins
There is also a good range of Assortment Kits - Various on the Small Parts and Bearings website.
Clutch Parts - Remote Control
Clutch Shoes, Springs, Clutch Bells
Clutch Shoes, Springs, Bells and Complete for Remote Control Cars.
Exhausts - Remote Control
Exhausts for Remote Control Cars
Exhaust Pipes, Headers, Springs, Couplers for 1/10, 1/8 and 1/5 Scale Cars.
Tools - Wire Working
For general hobby applications. Wire crimping and wire bending tools. Spring winder and spring looping.
Related Information:
There is also a good range of Tools - Wire Working on the Small Parts and Bearings website.
Exhaust Couplers - Remote Control
Exhaust couplers for Remote Control Cars
Exhaust Pipes, Headers, Springs, Couplers for 1/10, 1/8 and 1/5 Scale Cars.
Exhaust Deflectors - Remote Control
Exhaust deflectors for Remote Control Cars
Exhaust Pipes, Headers, Springs, Couplers for 1/10, 1/8 and 1/5 Scale Cars.
Exhaust Seals - Remote Control
Exhaust seals for Remote Control Cars
Exhaust Pipes, Headers, Springs, Couplers for 1/10, 1/8 and 1/5 Scale Cars.
2212 Outrunner Motor - AXI Parts
Bearings and Spare Parts for Remote Control Models
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Motors - DC 12.0X30.0 mm
6.0V - 22800 RPM
Related Information:
There is also a good range of Motors - DC 12.0X30.0 mm on the Small Parts and Bearings website.
Motors - DC 18.9X18.0X9.5 mm
M-020 Series - 1 to 3 VDC - 3700 to 11000 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft. Weight Approx 9.5 grams.
Related Information:
There is also a good range of Motors - DC 18.9X18.0X9.5 mm on the Small Parts and Bearings website.
Motors - DC 20.0X25.0 mm
1.5 to 4.5 VDC - 12,000 RPM unloaded at 3 volts
Related Information:
There is also a good range of Motors - DC 20.0X25.0 mm on the Small Parts and Bearings website.
Motors - DC 22.4X38.0 mm
Related Information:
There is also a good range of Motors - DC 22.4X38.0 mm on the Small Parts and Bearings website.
Motors - DC 23.8X30.6 mm
12 VDC - 12,300 RPM unloaded at 4.5 volts
Related Information:
There is also a good range of Motors - DC 23.8X30.6 mm on the Small Parts and Bearings website.
Motors - DC 24.3X12.35 mm
6.0 VDC - 4,900 RPM unloaded at 4.5 volts
Related Information:
There is also a good range of Motors - DC 24.3X12.35 mm on the Small Parts and Bearings website.
Motors - DC 25.0x20.1X15.1 mm
M-13 Series - 1.5 to 24 VDC - 4500 to 13760 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
There is also a good range of Motors - DC 25.0x20.1X15.1 mm on the Small Parts and Bearings website.
Motors - DC 25.0X21.0 mm
M-14 Series 1.5 to 3 VDC - 4230 to 11280 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
There is also a good range of Motors - DC 25.0X21.0 mm on the Small Parts and Bearings website.
Motors - DC 26.9X23.8 mm
M-26 Series 1.5 to 24 VDC - 2500 to 15100 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
There is also a good range of Motors - DC 26.9X23.8 mm on the Small Parts and Bearings website.
Motors - DC 26.9X24.2X18.3 mm
MF-26 Series - 1.5 to 24 VDC - 3600 to 15900 RPM. Standard 130 Size Hobby Motor.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
There is also a good range of Motors - DC 26.9X24.2X18.3 mm on the Small Parts and Bearings website.
Motors - DC 30.5X24.2 mm
M-28 Series 1.5 to 24 VDC - 2830 to 14250 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
There is also a good range of Motors - DC 30.5X24.2 mm on the Small Parts and Bearings website.
Motors - DC 30.5X24.2X18.3 mm
MF-28 Series - 1.5 to 24 VDC - 4470 to 13430 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
There is also a good range of Motors - DC 30.5X24.2X18.3 mm on the Small Parts and Bearings website.
Motors - DC 32.0x16.6 mm
M-500T Series 1.5 to 9 VDC - 1430 to 2230 RPM.
See Datasheets in PDF format. Link at bottom of this page. Direction of rotation (CW = Clockwise, ACW = Anticlockwise) when looking towards shaft.
Related Information:
There is also a good range of Motors - DC 32.0x16.6 mm on the Small Parts and Bearings website.
Motors - DC 6mm Diameter
Our smallest motors at an affordable price.
Various models 10000 to 30000 rpm. Low starting voltage of Less than0.8V. Rated Voltage 1.3V. Less than 43 dB Mechanical Noise Level. 100 hours / 100000 turns mechanical life. Clockwise rotation when viewed from shaft end. Not recommended for reversing.
Related Information:
There is also a good range of Motors - DC 6mm Diameter on the Small Parts and Bearings website.
Motors - DC 8.0X10.0 mm
3.5V - 20500 RPM
Related Information:
There is also a good range of Motors - DC 8.0X10.0 mm on the Small Parts and Bearings website.
Motors - Stepper - Basic Hobby
Small light weight stepper motor for your hobby or light duty projects
Motors - Vibrating
There is also a good range of Motors - Vibrating on the Small Parts and Bearings website.
Motors - Vibrating - Pager
Includes vibrating disc motor
There is also a good range of Motors - Vibrating - Pager on the Small Parts and Bearings website.
Snap Buttons - Double End
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
There is also a good range of Snap Buttons - Double End on the Small Parts and Bearings website.
Servo Motor - Accessories
Cases, gears and horns to suit popular servos
There is also a good range of Servo Motor - Accessories on the Small Parts and Bearings website.
Servo Motor - Analog - Sports
Standard Analog Sports Servo motors.
There is also a good range of Servo Motor - Analog - Sports on the Small Parts and Bearings website.
Servo Motor - Brackets
Brackets to suit servo motors for robotic applications
There is also a good range of Servo Motor - Brackets on the Small Parts and Bearings website.
Servo Motor - Hobby - General
For cars, planes, boats and helicopters. JR, Spektrum, Futaba and Hitec
Gear Strength: Using nylon as a base, Karbonite gears are 4x the strength, Metal gears 16x and Titanium Alloy 48x.
Related Information:
There is also a good range of Servo Motor - Hobby - General on the Small Parts and Bearings website.
Spa Jet Motor Multiple Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of Spa Jet Motor Multiple Parts on the Small Parts and Bearings website.
Assassin Mid Motor and Stock Option Corally Parts
Bearings and Spare Parts for Remote Control Models
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Twin Force -Motor Truck Kyosho Parts
Bearings and Spare Parts for Remote Control Models
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
Snap Buttons - Single End - Dog Leg
Fasteners for telescoping tubing help reduce assembly time whilst improving your product functionality. Also called button clips or spring buttons.
Eliminates the need for rivets and screws. Simply snap into place in square or round tubing. Made from 1050 heat treated spring steel with minimum 0.005mm (0.0002 inch) zinc plating.
There is also a good range of Snap Buttons - Single End - Dog Leg on the Small Parts and Bearings website.
Micromat-Athlet Type H240B Motor Muss Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of Micromat-Athlet Type H240B Motor Muss Parts on the Small Parts and Bearings website.
Park 480 E-Flite Parts
Bearings and Spare Parts
Where alternative parts are offered, we make no claims as to their suitability. Selection of the most suitable bearings and parts is the responsibility of the customer. We recommend you replace bearings with the same type if that type is working well. High speed caged bearings are better suited to handle vibration than standard caged bearings.
There is also a good range of Park 480 E-Flite Parts on the Small Parts and Bearings website.
Heatsink - Remote Control
Motor Heatsinks for Remote Control Cars
There is also a good range of Heatsink - Remote Control on the Small Parts and Bearings website.
Kits - Robotic Bases
Robotic bases include chassis, wheels, motors, gearboxes and hardware. Build your own robot.
Gearmotors - Basic - Hobby - 12.1mm Diameter
Small light weight geared motors used in toys and small solar applications
NOTE! These do not have a standard output shaft. The output is a plastic crossed block (see diagram) which is designed to be fitted to a fabricated coupling in O.E.M applications. However, the plastic block would be suitable for drilling and attaching objects with wire for rotating mobile type applications.
There is also a good range of Gearmotors - Basic - Hobby - 12.1mm Diameter on the Small Parts and Bearings website.
Main Pages
About Us
Balls List
Bearings List
Brands
Bulk Offers
Catalogue
Clearance Items List
Contact Us
Charity
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Small Bearings
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Hobby & Engineering Supplies Pty Ltd (ABN 54 125 001 541)
Hobby and Engineering Supplies offers 6228 products in 434 categories including low priced hobby bearings, screws, brass and aluminium rod and tubing, shim - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Hobby and Engineering Supplies is part of MBA Group offering a select range from the MBA Group catalogue.
Hobby and Engineering Supplies products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Hobby and Engineering Supplies 1997. All rights reserved.
