THREAD CATEGORIES
Threaded Rod
Threaded Rod - Unthreaded Centre - Steel
UNC Small range only. Threaded each end 38.1mm (1.5 inches) and unthreaded in the centre.
Related Information:
There is also a good range of Threaded Rod - Unthreaded Centre - Steel on the Small Parts and Bearings website.
Thread Inserts
Inserts - Thread Repair - Keylocking Starter Sets
Keylocking inserts are used to repair threads by tapping the worn thread to a standard larger thread, twisting the insert into place and then driving in the keys to lock the insert. Also known as keenserts.
Each kit contains an installation tool and the quantity of inserts shown. One size per kit. Also known as keenserts, keylocking inserts are available in mild steel and stainless steel. Installation is by drilling out the old thread, countersinking, tapping new thread with a standard tap, screwing the insert until slightly below the surface, then tapping down the keys using the tool supplied and a hammer.
Related Information:
There is also a good range of Inserts - Thread Repair - Keylocking Starter Sets on the Small Parts and Bearings website.
Inserts - Thread Repair - Recoil Starter Sets
Recoil inserts are screwed directly into an enlarged tapped hole. A tap and installation tool is included with these kits.
Stainless inserts. Contents: Ground intermediate (2nd) tap. Inserts. Installation/tang break off tool. Full instructions. Manufactured to BS 4377 BS 3049 parts 1 & 2. Recoil helically-wound thread inserts are formed from 18-8 (Type 304) Stainless Steel. The wire in most sizes has a tensile strength of greater than 200,000 P.S.I. and a finish better than 32 micro inches.
There is also a good range of Inserts - Thread Repair - Recoil Starter Sets on the Small Parts and Bearings website.
Inserts - Expansion - Press In - Brass
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
There is also a good range of Inserts - Expansion - Press In - Brass on the Small Parts and Bearings website.
Inserts - Expansion - Press In - Brass - Flanged
Use for cored or drilled holes in plastics. Designed to replace molded in inserts and threads in plastic casings. Also known as threaded inserts.
Material : Brass. Easiest inserts to install - simply push into a pre-moulded hole. Used with plastics or other materials. Material must be strong enough to withstand the expansion of the insert. The insertion of the screw locks the external knurls into the wall of the hole. Provides excellent thread durability. Not as strong as wind-in inserts.
There is also a good range of Inserts - Expansion - Press In - Brass - Flanged on the Small Parts and Bearings website.
Inserts - Self Tapping - For Aluminium - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from steel with zinc chromate finish.
Related Information:
There is also a good range of Inserts - Self Tapping - For Aluminium - Steel on the Small Parts and Bearings website.
Inserts - Self Tapping - For Plastics - Steel
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from steel with zinc chromate finish.
Related Information:
There is also a good range of Inserts - Self Tapping - For Plastics - Steel on the Small Parts and Bearings website.
Inserts - Self Tapping - For Aluminium - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut their own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Can be used in Aluminium, aluminium alloy or magnesium. Made from 303 stainless steel.
Related Information:
There is also a good range of Inserts - Self Tapping - For Aluminium - Stainless 303 on the Small Parts and Bearings website.
Inserts - Self Tapping - For Plastics - Stainless 303
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Provides a strong wear and vibration resistant thread. Use of installation tool recommended. Low volumes can be installed by winding in with a bolt through the threaded centre. Large volumes can be installed with hand installation tools (Sold Seperately). Hole sizes are reference only. Can variey on batchs. Optimum hole size is to be determinded through experimentation. A 60o countersink is required for flush mounting. Use with plastics, light metal alloys or hard wood. Made from 303 stainless steel. Quantity orders can also be supplied in Brass or 316 Stainless.
Related Information:
There is also a good range of Inserts - Self Tapping - For Plastics - Stainless 303 on the Small Parts and Bearings website.
Inserts - Self Tapping - For Wood - Hex Drive
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive on the Small Parts and Bearings website.
Inserts - Self Tapping - For Wood - Hex Drive - Flanged
Threaded inserts are screwed into preformed or predrilled holes and cut own threads into the wall of permanent installations.
Die Cast Zinc Alloy. Knife thread cuts easily into a predrilled hole. Inexpensive inserts for use in ready to assemble furniture, drawer pulls etc. Installs with a hex wrench.
There is also a good range of Inserts - Self Tapping - For Wood - Hex Drive - Flanged on the Small Parts and Bearings website.
You may also be interested in
Tools Threading
Tools - Thread Repair
Quickly repairs damaged screws
Twisting the handle opens and closes the floating blade around screw. Rotating the tool around screw quickly repairs damaged threads. Adjustable to suit both metric and imperial threads. Blades automatically adapt to any thread pitch or groove. Can be used on both Left and Right hand threads.
There is also a good range of Tools - Thread Repair on the Small Parts and Bearings website.
Tools - Die Holders
Bar and round holders. 16mm, 20.64mm and 25.4mm (inch). Also called a button die stock.
There is also a good range of Tools - Die Holders on the Small Parts and Bearings website.
Tools - Die Nuts
Tungsten Chrome Alloy - Carbon Steel die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
There is also a good range of Tools - Die Nuts on the Small Parts and Bearings website.
Tools - Tap Wrenches
Tee handle and bar types. Suit taps from 1mm to 12mm.
There is also a good range of Tools - Tap Wrenches on the Small Parts and Bearings website.
Tools - Dies - Carbon Steel
Tungsten Chrome Alloy - Carbon Steel Button dies and die nuts starting from M1 and 0-80 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
There is also a good range of Tools - Dies - Carbon Steel on the Small Parts and Bearings website.
Tools - Taps - Carbon Steel - Hand
Carbon Steel Straight Flute Taps. Starting from M1 and 0-90 UNF. Many unusual sizes - M1.2, M1.4, M1.6, M1.7, BA Sizes, 2-56 and more. Sutton - PN - Bordo.
Carbon steel hand taps. Carbon Steel (CS) Hand taps.
There is also a good range of Tools - Taps - Carbon Steel - Hand on the Small Parts and Bearings website.
Tools Measuring
Tools - Thread Gauge
Various types of gauges to help with identification of threads.
There is also a good range of Tools - Thread Gauge on the Small Parts and Bearings website.
Allthread
Studs - Full Thread - Stainless Steel
18-8 Stainless Steel Allthread Threaded Bar
Short lengths of threaded 18-8 stainless steel bar.
There is also a good range of Studs - Full Thread - Stainless Steel on the Small Parts and Bearings website.
Framing
Automat - Frame Kit Threaded Rods
All M3.5 Thread. See PDF file in FTP Directory for more information. Educational tool suitable for mechanical teaching institutions.
All M3.5 Thread Mild Steel.
Related Information:
There is also a good range of Automat - Frame Kit Threaded Rods on the Small Parts and Bearings website.
Screws Hex Head
Screws - Hex Head - Steel - Zinc Plated - Full Thread
BSW and METRIC - Set Screws
Related Information:
There is also a good range of Screws - Hex Head - Steel - Zinc Plated - Full Thread on the Small Parts and Bearings website.
Screws - Hex Head - Brass
Brass metal thread machine screws UNC and UNF
Nuts sold seperately - See Nuts.
Related Information:
There is also a good range of Screws - Hex Head - Brass on the Small Parts and Bearings website.
Screws Pan Head
Screws - Pan Head - Steel - Philips
Metal Thread Screws UNC - UNF - METRIC
Nuts sold seperately - See Nuts.
Related Information:
There is also a good range of Screws - Pan Head - Steel - Philips on the Small Parts and Bearings website.
Nuts Specialty
Nuts - Blind
Blind nuts - Tee nuts.
Put steel threads in soft materials like wood without counterboring.
There is also a good range of Nuts - Blind on the Small Parts and Bearings website.
Screws Cheese Head
Screws - Fillister Head - Brass - Slotted
Brass metal thread machine screws BA and METRIC
Nuts sold seperately - See Nuts.
Related Information:
There is also a good range of Screws - Fillister Head - Brass - Slotted on the Small Parts and Bearings website.
Screws Round Head
Screws - Round Head - Brass - Slotted
Brass metal thread machine screws BSW - UNF - UNC
Nuts sold seperately - See Nuts.
Related Information:
There is also a good range of Screws - Round Head - Brass - Slotted on the Small Parts and Bearings website.
Screws Hex Head
Screws - Hex Head - Titanium CP Grade 1
Fully threaded hex head set screws (DIN933). CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Din 933. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.
Related Information:
There is also a good range of Screws - Hex Head - Titanium CP Grade 1 on the Small Parts and Bearings website.
Screws Pan Head
Screws - Pan Head - 303-304 Stainless - Philips
Metal Thread Screws UNC - UNF - METRIC - Pan, cheese, fillister and round head.
Nuts sold seperately - See Nuts.
Related Information:
There is also a good range of Screws - Pan Head - 303-304 Stainless - Philips on the Small Parts and Bearings website.
Screws - Pan Head - Titanium CP Grade 1 - Philips Drive
Metal Thread Screws. Metric only. CP1 Commercially Pure Titanium Grade 1. Tensile Strength 24.6 kgf/mm2. Yield Strength 17.6 kgf/mm2. Elongation 24 Percent.
Nuts sold seperately - See Nuts. Commercially pure for general industrial corrosion applications. UNS R50250. Widely used in power generation, chemical processing, aerospace and medical applications. Composition Percentage: Al 0, V 0, N 0.03, C 0.08, H 0.015, Fe 0.2, O 0.18, Ti Balance.
Related Information:
There is also a good range of Screws - Pan Head - Titanium CP Grade 1 - Philips Drive on the Small Parts and Bearings website.
Screws Self Tapping
Screws - Self Tapping - For Soft Plastics - Pan Head
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics. Be sure to select correct screw for hard or soft plastic threadcutting.
There is also a good range of Screws - Self Tapping - For Soft Plastics - Pan Head on the Small Parts and Bearings website.
Screws - Self Tapping - For Hard or Soft Plastics - Pan Head
Tri-Lobe Course Thread Plastic Threading Screws
Thread cutting screws for plastics. Be sure to select correct screw for hard or soft plastic threadcutting.
There is also a good range of Screws - Self Tapping - For Hard or Soft Plastics - Pan Head on the Small Parts and Bearings website.
Locking Compounds
Threadlockers
ZAP, Molytec, Loctite, Pacer. Pipe sealant, low to high strength threadlockers. Hydraulic threadlocker. Wick-In. Stops threads loosening from vibration.
There is also a good range of Threadlockers on the Small Parts and Bearings website.
Bungs and Caps - Reversible - Round
Tapered plastic bungs fit inside round tube or over the outside ends of rod, tube or shafting.
Can be used on threaded or unthreaded parts. Used as tuning bungs or rod tips. Helps prevent damage to the product ends. Helps prevent injury from sharp edges.
Related Information:
There is also a good range of Bungs and Caps - Reversible - Round on the Small Parts and Bearings website.
Nuts - Hexagonal - Brass
UNC - UNF - BA - METRIC.
Note! Thickness (H) and A/F (A) dimensions are usually considered not critical and may vary. If the A and H dimensions are critical for your application please consult us prior to ordering. Nuts marked as type SCALE have the same dimension across flats as the brass hex head screw of the same thread size.
There is also a good range of Nuts - Hexagonal - Brass on the Small Parts and Bearings website.
Dubro Accessories Listed by Description
Accessories for model airplanes and other hobbies.
Allen Keys, Antenna Cowlings, Antenna Tubes, Axles, Ball Links, Ball Drivers, Bellcranks, Cables, Clevis, Clips, Collars, Connectors, Control Horns & Links, Couplings,. Crimps, DVDs, Fittings, Fuel Bottles, Fuel Connectors, Fuel Systems, Fuel Tank, Fuel Tube, Gas Conversion Stoppers, Gear Block Sets, Heat Shrink, Hinges, Horns,. Kwik Grips, Kwik Starts, Kwik Stops, Landing Gears Latchs, Linkages, Links, Mixers, Mounts, Nuts, Pumps, Push Rods, Reamers, Retainers, Rod Ends, Screws,. Screwdrivers, Servo Arms, Servo Savers, Shafts, Spinners, Steering Arms, Stoppers, Switches, Tap & Drill Sets, Tape, Threaded Rods, Tools, Tube Benders,. Turnbuckles, Valves, Washers, Wheels, Wheel Covers, Wheel Retainers, Wing Mount Kits, Wrenchs, Push-Pull Cable.
Main Pages
About Us
Balls
Bearings
Brands
Catalogue
Clearance Items
Contact Us
Contact
Freight Rates and Shipping Times
Frequently Asked Questions
Games Clearance
Google Search
Hobby Clearance
Hobby Information
Large Bearings
Mailorder Form
Order History
Ordering
Payment and Shipping
Privacy
Product Showcase
Shipping Rates and Times
Small Bearings
Technical
Terms
Freight Rates
Terms and Conditions
Privacy Policy
Registered Australian Company: Hobby & Engineering Supplies Pty Ltd (ABN 54 125 001 541)
Hobby and Engineering Supplies offers 6173 products in 447 categories including assortment kits, low priced hobby bearings, tools, screws, brass and aluminium rod and tubing - see the full listing in the Online Catalogue. We have excellent Freight Rates within Australia and worldwide. We offer a choice of delivery with a signature required, or cheaper options with no signature required. The no signature required options are at the customer’s risk once the goods leave our store.
Using the links throughout this site you will find extensive information including catalogues, technical data, and other product specific information. We sell our products worldwide through our online store and our overseas freight rates are competitive for fully traceable courier delivery.
Hobby and Engineering Supplies is part of MBA Group offering a select range from the MBA Group catalogue.
Hobby and Engineering Supplies products are not authorised for sale into the USA or Canada due to the reluctance of Australian insurers to provide product liability insurance into those two countries.
Information on this website is Copyright Hobby and Engineering Supplies 1997. All rights reserved.
